Warranty

ManualsBrandsExcell ManualsOutdoor Power Equipment3100 PSI 2.8 GPM 212cc OHV Gas Pressure Washer

PRESSURE WASHER

OPERATION MANUAL

for model EPW2123100

IMPORTANT: Please make certain that the person who is to use this equipment carefully reads

and understands these instructions before operating.

Part No. E110166// Rev. 0

10/31/2016 PRINTED IN CHINA

Record All Information and attach sales

receipt here for future reference:

Purchase Date:__________________________

Serial #: ________________________________

Questions? 1-888-895-4549

Refer to the website for electronic

manual and parts book.

www.powermate.com

TABLE OF CONTENTS

Safety Guidelines/Denitions ........................... 2

Consumer Safety Information .......................... 2

Important Safety Instructions .......................... 2

Safety Features ............................................... 6

Specications .................................................. 6

Assembly instructions ..................................... 7

Spray Nozzle Selection .................................... 9

Before Operation ............................................. 9

Engine and Pump Features ........................... 10

Operating Connections.................................. 10

Operating Instructions ................................... 11

Start-Up Procedure ....................................... 11

Chemical Injection ......................................... 11

Cleaning Techniques ..................................... 12

End of Cleaning Operation ............................ 12

Maintenance .................................................. 13

Storage .......................................................... 14

Warranty ........................................................ 15

Troubleshooting Guide .................................. 16

Français ......................................................... 17

Español .......................................................... 33

Summary of content (16 pages)

PAGE 1
PRESSURE WASHER OPERATION MANUAL for model EPW2123100 Record All Information and attach sales receipt here for future reference: Purchase Date:__________________________ Serial #: ________________________________ Questions? 1-888-895-4549 Refer to the website for electronic manual and parts book. www.powermate.com TABLE OF CONTENTS Safety Guidelines/Definitions �� 2 Start-Up Procedure........................................
PAGE 2
SAFETY GUIDELINES - DEFINITIONS • SAVE ALL INSTRUCTIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these symbols. DANGER CAUTION Indicates an imminently hazardous situation which, if not avoided , WILL result in DEATH OR SERIOUS INJURY.
PAGE 3
IMPORTANT SAFETY INSTRUCTIONS (CONT.) • SAVE ALL INSTRUCTIONS DANGER RISK OF EXPLOSION FOR FIRE (CONT.) WHAT CAN HAPPEN HOW TO PREVENT IT • Materials placed against or near the pressure washer can interfere with its proper ventilation features causing overheating and possible ignition of the materials. • Never operate pressure washer in an area containing dry brush or weeds.
PAGE 4
IMPORTANT SAFETY INSTRUCTIONS (CONT.) • SAVE ALL INSTRUCTIONS DANGER RISK OF INJURY FROM SPRAY WHAT CAN HAPPEN HOW TO PREVENT IT • High-velocity fluid spray can cause objects to break, propelling particles at high speed. • Light or unsecured objects can become hazardous projectiles. • Always wear ANSI-approved z87.1 safety glasses. Wear protective clothing to protect against accidental spraying. • Never point wand at or spray people or animals.
PAGE 5
IMPORTANT SAFETY INSTRUCTIONS (CONT.) • SAVE ALL INSTRUCTIONS WARNING RISK OF HOT SURFACES WHAT CAN HAPPEN HOW TO PREVENT IT • During operation, touch only the control surfaces of the pressure washer. Keep children away from the pressure washer at all times. They may not be able to recognize the hazards of this product. • Contact with hot surfaces, such as engine's exhaust components, could result in serious burn.
PAGE 6
SAFETY FEATURES • SAVE ALL INSTRUCTIONS THERMAL RELIEF VALVE A thermal relief valve is provided to protect the pump from overheating if the spray gun is closed for an extended length of time or the nozzle becomes plugged. However, it is intended to be used as a backup system and every effort should be made to not permit the pump to heat up. We recommend turning the pressure washer off if it will not be used for more than five minutes.
PAGE 7
ASSEMBLY INSTRUCTIONS • SAVE ALL INSTRUCTIONS 1. Place the unit on its back and insert wheel axle into front tube. Use (1) M6 washer and (1) M6 x 15mm long hex head screw to assemble wheel axle to frame using the supplied open-end wrench. Tighten securely. Repeat for opposite side. 2. Remove (1) M8 washer and (1) M8 nut from wheel axle and place wheel onto axle. Be sure the hub on the wheel goes to the inside. Re-assemble the washer and nut onto axle using the supplied open-end wrench. Tighten securely.
PAGE 8
ASSEMBLY INSTRUCTIONS (continued) • SAVE ALL INSTRUCTIONS 4. Remove the handle and rotate 180 degrees and re-insert into the frame. Re-assemble both knobs and screws. 5. Assemble the lower gun hook using (1) M6 x 45mm long socket head cap screw, (1) M6 nut, and the supplied hex wrench and openend wrench. Tighten securely. 6. Assemble the upper gun hook using (1) M6 x 45mm long socket head cap screw, (1) M6 nut, and the supplied hex wrench and openend wrench. Tighten securely. 7.
PAGE 9
SPRAY NOZZLE SELECTION • SAVE ALL INSTRUCTIONS 25° High Pressure (Green): Use of this nozzle offer both a medium coverage and water stream. Best used for flushing dirt and debris off surfaces. Following is information concerning the five nozzles provided with your pressure washer. NOTE: The force of the spray on the surface you are cleaning increases as you move closer to the surface. 0° High Pressure (Red): The water stream discharged is very aggressive.
PAGE 10
ENGINE AND PUMP FEATURES - FIGURE 1 • SAVE ALL INSTRUCTIONS OUTLET CONNECTION SIPHON INJECTOR FUEL FILL INLET CONNECTION AIR FILTER THERMAL RELIEF VALVE THROTTLE LEVER FUEL FILTER OIL FILL CHOKE LEVER OIL DRAIN FUEL ON/OFF RECOIL STARTER ENGINE ON/OFF SWITCH OPERATING CONNECTIONS • SAVE ALL INSTRUCTIONS HIGH PRESSURE HOSE Attach the high pressure hose to the outlet connection located on the pump. (See Figure 1).
PAGE 11
OPERATING INSTRUCTIONS • SAVE ALL INSTRUCTIONS START-UP PROCEDURE 1. Ensure water supply is connected and turned on. 2. Release gun safety lock. 3. To allow air to escape from the hose, squeeze trigger on the gun until there is a steady stream of water coming from the nozzle. 4. Remove any dirt or foreign matter from the gun outlet and the male connector of the wand. 5. Insert the nozzle wand into the gun wand and tighten the twistfast fitting securely by hand.
PAGE 12
CLEANING TECHNIQUES • SAVE ALL INSTRUCTIONS When cleaning with the pressure washer, many cleaning tasks can be solved with water alone, but for most tasks it is advantageous to use a detergent also. A detergent ensures a quick soaking of the dirt allowing the high pressure water to penetrate and remove the dirt more effectively. 2. Allow chemical to remain on the surface for a short time before rinsing. 3. Rinse with clean water under high pressure.
PAGE 13
MAINTENANCE • SAVE ALL INSTRUCTIONS CONNECTIONS Connections on pressure washer hoses, gun and spray wand should be cleaned regularly and lubricated with silicon grease to prevent leakage and damage to the o-rings. NOZZLE Clogging of the nozzle causes the pump pressure to be too high and cleaning is immediately required. WATER SCREEN The pressure washer is equipped with a water inlet screen to protect the pump.
PAGE 14
STORAGE • SAVE ALL INSTRUCTIONS PUMP STORAGE ENGINE STORAGE If you must store your pressure washer in a location where the temperature is below 32°F, you can minimize the chance of damage to your machine by utilizing the following procedure: When the pressure washer is not being operated or is being stored more than one month, follow these instructions: 1. Shut off water supply and relieve pressure in the spray gun by depressing the trigger.
PAGE 15
LIMITED WARRANTY • SAVE ALL INSTRUCTIONS Always specify model number when contacting the manufacturer. We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.
PAGE 16
TROUBLESHOOTING GUIDE • SAVE ALL INSTRUCTIONS Problem Cause Correction Engine will not start or stops while operating 1. Low-oil shutdown. 2. Engine switch not in the “ON” position. 3. Pressure build up in hose. 1. Fill engine with oil. 2. Turn switch “ON”. 3. Squeeze trigger. Engine is overloaded 1. Nozzle partially blocked. 1. Clean nozzle. Water or oil leaking from bottom of pump 1. A small amount of leakage is normal. 1. If excessive leaking occurs call the Customer Service Department.