Owner's manual

4
level of the unit and the outlet, or the connector if an extension
cord is used, to prevent water from traveling along the cord and
coming in contact with the outlet or light unit. If the plug or outlet
does get wet, DON’T unplug the electrical cord. Disconnect the
fuse or circuit breaker that supplies power to the appliance, then
unplug and examine for presence of water in the outlet.
• This equipment is FOR INDOOR USE ONLY.
• Warning: Disconnect the plug of this light unit, and any other
electrical equipment, used for the terrarium, paludarium or
aqua-terrarium before placing your hands in the water; and/or
performing any maintenance of any kind.
• Warning: Whenever installing, removing, changing or maintaining
Exo Terra
®
SunRay bulbs (or any other metal halide bulbs) always
ensure that the fixture is unplugged.
SAVE THESE INSTRUCTIONS.
Only the faithful observation of these installation, electrical and
maintenance guidelines will ensure the safe and efficient use of
this appliance.
The Exo Terra
®
SunRay is a fixture designed for use with the
Exo Terra
®
SunRay bulbs and the Exo Terra
®
Glass Terrariums.
Exo Terra
®
Metal Halide Fixture Installation instructions
RECOMMENDATION: Use only Exo Terra
®
Sunray bulbs as per the
wattage rating indicated on the electrical data label located on the
fixture. UV radiation slowly decreases over time. To assure that your
animals continuously receive the right amount of UV, we recommend
to replace the Exo Terra
®
Sunray bulb every 12 months. Subscribe to
our “Restore the Rays” program on www.exo-terra.com to receive a
reminder when your Exo Terra
®
Sunray bulb needs to be replaced.
INSTALLATION OF LIGHTING UNIT (p. 38)
1. Clean the outside surface of the terrarium glass
2. With the protective backing still intact, place the SunRay fixture
adhesive supporting base on the back or the side of the terrarium
to determine its final position.
3. Mark the position with a wax pencil or other marker.
4. Remove the protective backing and carefully fit the adhesive
supporting base within the marked area.
5. Make sure the tape is pressed evenly against the terrarium glass
and that no air bubbles are showing.
6. Press the adhesive sides firmly against the glass panel for at
least 30 seconds.
7. Wait a few moments and make sure the tape is attached firmly to
the terrarium before releasing the fixture.
8. Once in place, the SunRay fixture should not be removed.
9. Adjust the height and tighten the screw of adhesive supporting
base when the Exo Terra
®
SunRay fixture is suspended above the
terrarium at the desired height. Grasp the fixture at the
point indicated.
10. Ensure that the light’s focal point is not positioned above any
plastic parts of the terrarium or screen cover to prevent damage.
children) with reduced physical sensory or mental capabilities,
or lack of experience or knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
5. To avoid injury, do not contact hot parts, allow to cool down
before handling.
6. Do not use the appliance for other than intended use. The use
of attachments not recommended or sold by the appliance
manufacturer may cause an unsafe condition.
7. The Exo Terra
®
SunRay Bulb emits UV and was designed strictly
for use with reptiles. It should be operated in a way that humans
are never exposed to UV. Before handling the bulb, and to avoid
exposing yourself to the light emitted by the bulb, switch off the
bulb and let it cool down.
8. Never look directly into the bulb.
9. Do not install or store the appliance where it will be exposed to
weather or to temperatures below freezing.
10. The safety of this appliance is guaranteed only provided that the
bulbs, adaptors, and light unit is properly installed.
11. Do not use more than one bulb on one ballast.
12. Damaged bulbs or bulbs that do not function properly have to be
removed immediately.
13. Provide sufficient ventilation. Never cover the bulb or ballast.
14. Never install the bulb near flammable objects.
15. The housing of this bulb may only be opened by authorized
personnel or by the manufacturer.
16. Switch off the bulb before performing any maintenance of any
kind in the terrarium.
17. Disconnect the plug of the light unit, and any other electrical
equipment, used for the terrarium, paludarium or aqua-terrarium
before placing your hands in the water; and/or performing any
maintenance of any kind.
18. Whenever installing, removing, changing or maintaining bulbs
always ensure that the device is unplugged.
19. If an extension cord is necessary, a cord with a proper rating
should be used. A cord rated for less amperes or watts than the
appliance rating may overheat. Care should be taken to arrange
the cord so that it will not be tripped over or pulled.
20. DANGER – To avoid possible electrical shock, special care should
be taken. For each of the following situations, do not attempt
repairs yourself; return the appliance to an authorized service
facility for service or discard the appliance:
A. If the appliance falls into the water, DON’T reach for it! First
unplug it and then retrieve it. If the electrical components of the
appliance get wet, unplug the appliance immediately.
B. Carefully examine the appliance after installation. It should not
be plugged in if there is water on parts not intended to be wet.
C. Do not operate any appliance if it has a damaged electrical cord
or plug, or if it is malfunctioning or if it is dropped or damaged
in any manner. The power cord of this appliance
cannot be replaced: if the cord is damaged, the
appliance should be discarded. Never cut
the cord.
D. To avoid the possibility of the appliance plug
or electrical outlet getting wet, position the
appliance to one side of a wall mounted outlet
to prevent water from dripping onto the outlet
or plug. A “drip-loop” should be arranged. The
“drip-loop” is that part of the cord below the
ENGLISHFRANÇAISDEUTSCHESPAÑOLITALIANONEDERLANDS