Content Precaution..................................... 2 Digital Video Special Function....... 24 Safety Information......................... 3 Multi-subtitle language function........ 24 Disc Note....................................... 4 Multi-audio language function........... 24 Installation .................................... 5 Multi-angle function......................... 24 Detaching control panel.................... 7 Title menu function ..........................
Precaution THANK YOU FOR PURCHASING THIS CAR Digital Video PLAYER . Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit . ON INSTALLATION DO NOT install any receiver in locations where; - it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
Safety Information CAUTION: THIS Digital Video PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DIGITAL VIDEO PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE . HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DIGITAL VIDEO PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Disc Note Disc formats supported by this player Digital Video Digital Video Audio and Video Disc size 12 cm VCD VCD Audio and Video Disc size 12 cm CD CD Audio Disc size 12 cm MP3 MP3 Audio Disc size 12 cm Discs which cannot be played with this player Digital Video-RAM CDV CDG Handling and Cleaning Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs.
Installation NOTES: 1. Choose the mounting location where the unit will not interfere with the normal driving function of the driver. 2. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. 3. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. 4.
Installation 3. Remove the PLASTIC COVER of the both sides away PLASTIC COVER 4. Insert the two KEY PLAT into the grooves at both sides of the unit as shown in figure until they click . KEY PLATE 5. Pulling the levers makes it possible to remove the unit from the dashboard .
Installation How To Remove And Install Control Panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching Control Panel Before detaching the control panel, be sure to turn off the power. 1). Press the “REL” release button and the left hand side of front panel will release. RELEASE BUTTON 2). Pull-off the front panel and keep the front panel into the case . PROTECTIVE CASE Attaching Control Panel 1).
Panel Angle Adjustment CHANGING THE CONTROL PANEL ANGLE When you want to change the viewing angle of the operating unit to play, you can touch the section on touch screen (or press the button on the front panel) repeatedly to select the desired angle as follows: ANGLE 1 - ANGLE 2 - ANGLE 3 - ANGLE 4 - ANGLE 1 . ANGLE 1 ANGLE 2 ANGLE 4 ANGLE 3 Caution: Do not insert your finger behind the control panel.
Electric Connection WIRING CONNECTION REAR AUX OUTPUT AUDIO OUTPUT-R(RED) AUDIO OUTPUT-L(WHITE) REARVIEW CAMERA INPUT(YELLOW) AUDIO INPUT-R(RED) SUBWOOFER OUTPUT (GREY) AUX INPUT FRONT AUX OUTPUT VIDEO INPUT(YELLOW) AUDIO OUTPUT-R(RED) VIDEO OUTPUT (YELLOW) AUDIO INPUT -L(WHITE) AUDIO OUTPUT-L(WHITE) RADIO ANTENNA JACK BROWN IGNITION SWITCH(B+) MEMORY BACK-UP(B+) REVERSE TRIGGER(BROWN, B+) RED ORANGE YELLOW GROUND(B-) BLUE BLACK FRONT LCH SPK. REAR LCH SPK.
Remote Control 15 MODE 17 7 2 MUTE PLAY/PAUSE 16 STOP 3 REDIAL ANGLE MO/ST ZOOM 19 13 22 20 PAIR 1 LOUD MENU EQ CLK LO/DX 21 6 14 23 OSD 24 18 BAND 9 ENTER TITLE/PBC A/PS TOP RPT INT 1 2 3 4 5 6 SEL 7 8 9 SETUP GOTO +10 0 VOL 11 10 4 VOL 1 CLK 2 PAIR/ 3 STOP 4 SETUP 12 RDM 8 Ref # Button 5 27 26 25 Function Press it briefly to view the clock time , Press again to return to normal display mode . Press longer to set the time .
Remote Control Ref # Button 8 GOTO 9 / Function Press it button to begin playback at a moment in the program you designate. Use number buttons to enter the data that is needed. In BT menu, it serves as the asterisk button on your mobile handset. Press these buttons to skip ahead or back one track.
Remote Control Function Ref # Button 23 This button is used to confirm selections and settings within ENTER many of the menus in the OSD system. In Disc playback mode, press it to search reverse rapidly 24 25 0-9 Use to input numerical values during programming, with the GOTO button, or to directly select a track to play . 26 +10/ This button is used with the other number buttons for use with two-digit number entries. In BT menu, it serves as the hash button on your mobile handset.
Basic Operation TFT Monitor Adjustment In Digital Video mode , touch screen of “ range to enter the main menu .
Basic Operation ANIMATION In RADIO mode, you can change the playing time of animation among of “10SEC, 30SEC, 60SEC,90SEC, 2MIN, 3MIN, 4MIN and OFF ”. Note: Please set the playing time of the animation to “ 10SEC ” for the first, when you turn the unit on . SUBWOOFER Touch to switch the SUBWOOFER function ON and OFF . BALANCE: R 0-10 to L 0-10 Adjust sound balance between left and right speakers . FADER: F 0-10 to R 0-10 Adjust sound balance between front and rear speakers .
Basic Operation touch the “ / ” ranges to select the adjustment item, touch the “ / ” ranges to adjust the selectment item , then touch “ SET ” icon to confirm . It`s depend on your need to setup the data . EXTERNAL AUDIO SOURCE On the front panel of the unit , there is an AUX IN jack, to connect analogue replay devices. Use this jack to replay sound of other replay equipment such as MP3 players, etc. Via the loudspeakers.
Control Panel Unit Keys : 10 9 8 7 6 5 4 SEL MIC 12 REL MOD RET CH1-6 13 VOL 3 IR 2 AUX IN 1 Control Panel 11 Sliding Plate diagram after remo ving Control Panel 1 AUX Input JACK For information about connecting a AUX device, please see page 30 . 2 IR SENSOR 3 VOL+/ VOL- KNOB In normal mode, this knob is used to increase or decrease the volume. It is also used as an UP/DOWN knob when audio or video settings are being adjusted when accessed using the SELECT button.
Control Panel 5 /CH 1-6 (RADIO PRESET) BUTTON A) In Disc Playback Mode Press this button to pause playback, press it again to resume playback. B) In Radio Mode Press this button repeatedly to preset station. With this system a total of 30 stations can be stored in the memory . Each band store up to six preset stations. The stations might be FM1, FM2, FM3, AM1 (MW1) and AM2 (MW2) band. -Store in Memory > Select the frequency band > Press repeatedly the button to select the desired memory key .
Touch Screen Operation (10) Touch to change the frequency band . RADIO Operation Listening to the radio Press repeatedly the MOD button on the front panel to select the RADIO mode . (You can enter the main menu to select the RADIO mode ) Touch Screen Configuration (1) (2) 87.50 Radio (3) FM1 MHZ DX ST FLAT SWF (15) APS (4) (14) (13) 1 87.50 2 90.00 3 98.00 (12) Touch : recalling the preset station. Touch and hold: storing broadcast station .
Touch Screen Operation Automatic Search During Radio mode, touch and hold (for more than 2’s ) the screen of “ / section to start search for a radio station automatically . ” - Retrieve a preset station Touch the 1-6 ranges briefly to retrieve a station which had been stored in the memory in advance the chose number is shown on display .
Touch Screen Operation DISC Operation In any modes, repeatedly press MOD button on front panel to enter the disc play mode . The message will display as below : (When Parking Brake supplied .) To skip the previous track To search the disc with numbers In DVD mode, touch to display the menu. In VCD mode, touch to switch the PBC ON and PBC OFF.
Touch Screen Operation BASIC OPERATION Note: when the JPEG disc playback, in normal mode, you can use the cursor buttons to rotate the picture . Press UP to invert an image . Press DOWN to mirror an image . Press LEFT to rotate an image to left . Press RIGHT to rotate an image to right . Stopping Play Touch the screen the range to stop the unit playback. touch the range to start play.
Touch Screen Operation FOR VCD : Touch the screen of the “INT” section (or longer press the 3/INT button on the the remote control ). It display will following menu as below : SEQ PLAY INTRO 1 Note: when select the INTRO Mode, this player to start to play the previous 10 seconds part of each track/chapter on disc. (Touch it again to cancel this mode .) REPEAT function Refer to see page 21 . INTRO function Refer to see page 21 . RANDOM function Refer to see page 22 .
Touch Screen Operation ON-SCREEN DISPLAY FUNCTION OSD During playback, touch the screen of the OSD section, it will display the following as below : 1. Digital Video: A.Touch or Press OSD for first time: 2.Example for VCD/SVCD/CD: A.Touch or Press OSD for first time: VCD TRK 1/19 A PBC C 0:01:36 B.Touch or Press OSD for second time: VCD TRK 1/19 A PBC C -0:06:06 Digital Video TT 01/01CH 04/31 C 0:02:06 C.
Touch Screen Operation Digital Video Special Function 3. Multi-Angle Function (for Digital Video Only) 1. Multi-subtitle Language Function (for Digital Video Only) During Digital Video playback, touch the ANGLE button on the touch screen . Each time the button is pressed , the number of the angle changes in sequential order. Notes: - The angle number is different according to the disc. - The function only work for disc having scenes recorded at different angles.
Touch Screen Operation SYSTEM SETUP Multi-media Setup Menu SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT NTSC PAL AUTO EXIT EXIT 1. Touch the screen of “ ” range or press the SETUP button on remote . 2.The SETUP menu is displayed. 3.Touch directly the desired item to select the preferred item . Or by using the / / / buttons . 4.
Touch Screen Operation SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT 4:3PS 4:3LB 16:9 EXIT 16:9 ----- EXIT 4:3 Letter Box 4:3 Pan Scan TV DISPLAY SETUP This is to select the appropriate TV aspect (4:3 or 16:9) according to the connected TV set. Normal/PS (For 4:3 TV) Played back in the PAN & SCAN style. (If connected to wide-screen TV, the left and right edges are cut off.
Touch Screen Operation SYSTEM SETUP LANGUAGE SETUP ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT RESTORE EXIT EXIT DEFAULTS Selecting the DEFAULT item and confirming RESTORE will return ALL personal settings you have made, including radio and TV presets, to the factory default settings.
Touch Screen Operation VIDEO SETUP LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN 12 10 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS EXIT EXIT DISC MENU LANGUAGE SETUP Select the preferred DISC MENU language by touching directly the desired language . CONTRAST- the contrast of the video signal (the dark portions of pictures).
Touch Screen Operation DIGITAL SETUP VIDEO SETUP 12 10 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS DIGITAL SETUP DYNAMIC RANGE FULL 6/8 4/8 2/8 OFF EXIT EXIT SATURATION- the saturation of the video signal (the vividness of the color) all above can be adjusted to your tasters . DYNAMIC RANGE CONTROL Select DRC and adjust the dynamic range of a Dolby Digital encoded program. There are 8 steps between full compression and off compression.
Touch Screen Operation AUX Operation To return to the main menu This unit features AUX IN line input jacks on both the front (headphone type) and rear (RCA type ) panel . follow the diagram below to connect analogue replay devices. Use this jack to replay sound of other replay equipment such as Digital Video players, computers, etc. Via the loudspeakers. 1). Please connect the external device with stereo jack plug the Aux in socket . AUX 1 IN Function zone 3).
Touch Screen Operation BT OPERATION IMPORTANT: 1. “Pair” To Your BT Phone Prior to using the Car Kit for the fist time, you must pair it with a BT-enabled mobile handset. The following steps describes pairing the instruction for a typical BTenabled mobile handset. 1). Place the Car Kit and mobile handset in 3 meters apart. 1). If the pairing can not be completed within approximately 2 minutes , whiles the pairing mode is activated, and you will need to reattempt pairing (See steps 2-5 above) . 2).
Touch Screen Operation ANSWER A CALL PLAY BT MUSIC After you hear the ring tone, a incoming telephone number will display on the TFT monitor . Touch the screen of “ ” range to listen or press the “PAIR/ ” button shortly on the remote control . In BT mode, repeatedly the MOD on the panel to select the “BT MUSIC” Mode .
Touch Screen Operation USB Operation Following the diagram below, connect your USB device to the front panel USB port . If it is properly connected, the device will be mounted and start playing automatically. Changing From DISC to USB Playback Modes If the disc present in the player is an Digital Video or VCD or MP3/WMA or MP4 disc, touch the screen of the “ ” range to enter the home menu, then touch the “USB” ICON to enter the USB mode .
Other Main Operation SD/MMC card OPERATION The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are stored into SD and MMC memory card . Please read below before you start the operation of memory card . Inserting a SD or MMC card . Label side facing upward REL button Press REL button to detach control panel . First hold the left end up a little and then pull it leftwards to remove. Insert a card, push in till heard a “CLICK”, then attach the control panel again to play.
Touch Screen Operation MP3/WMA/JPEG/MPEG4 DISC PLAY The unit is support MP3/WMA/JPEG/MPEG4 . When a disc is inserted into player, the following picture will appear on the monitor . The unit will play the first track automatically . You can touch to directly others mode (MP3/JPEG /MPEG4) to play . EX. : when the MP3 mode is selected . 2 1 Current type (highlighted bar) . [MP3] ITLE / SONG: TRACK 03 / 2 Current track (ID3 TAG display) . 001 WMA 002 1 Mp3 003 3 The current play mode(MP3).
Specification Generall : Supply Voltage: Current Consumption: Signal System: Discs Played: 12V DC (11V-15V) Less than10 A Compositive video 1.
Troubleshooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. SYMPTOM No power CAUSE SOLUTION The car ignition switch is not on The fuse is blown If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC" Replace the fuse Presence of disc inside the Remove the disc in the player, then put a new one player.
