Contents Precautions ................................... 2 Selecting Subtitles ..........................27 Safety Information......................... 3 Selecting multi-angle views .............. 27 Disc Notes .................................... 4 Title menu function .......................... 27 Installation .................................... 5 Setup .............................................28 Detaching the front panel ................. 7 System Setup..................................
Precautions THANK YOU FOR PURCHASING THIS CAR DVD PLAYER . Before operating the unit, read this manual thoroughly and keep it handy for future reference . To avoid injury or accident , read the following precautions before installing and operating the unit . ON INSTALLATION DO NOT install any receiver in locations where; - it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic accident.
Safety Information CAUTION: THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE . HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Disc Notes Disc formats supported by this player DVD DVD Audio and Video Disc size 12 cm VCD VCD Audio and Video Disc size 12 cm CD CD Audio Disc size 12 cm MP3 MP3 Audio Disc size 12 cm Discs which cannot be played with this player DVD-RAM CDV CDG Handling and Cleaning Dirt, dust, scratches and warping disc will cause misoperation. Do not place stickers or make scratches on discs. Do not warp discs. A disc should always be kept in its case when not in use to prevent from damaging.
Installation NOTES: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
Installation Installating the unit DASH BOARD HEX NUT METAL MOUNTING STRAP SPRING WASHER CONSOLE PLAIN WASHER SLIDE BRACKET HOUSING TAPPING SCREW HEX BOLT TABS SCREWDRIVER KEY PLATE PLASTIC TRIM OUT KEY PLATE If you want to take CHASSIS out of the SLIDE BRACKET HOUSING, first remove the PLASTIC TRIM OUT of the both sides away, then insert the two KEY PLATE into left and right side of chassis as above illustration.
Installation How To Remove And Install The Front Panel When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching The Front Panel Before detaching the control panel, be sure to turn off the power. 1). Press the “REL” release button to flip down the front panel . REL button 2). First slide the guide knob to remove the right side , and pull it off towards you . GUIDE Knob 3).
Installation ATTACHING THE FRONT PANEL 1). First, insert the right side of the front panel into the main unit. (Note: the “Hollow ” point on the front panel must be attached into the “Bulge” point of the unit . ) Bulge Bulge Hollow Hollow 2). Push the left side of the front panel until it locks firmly into the main unit, at one time, insert the right side of the front panel into the main unit . 3). Push it back to the position for playing.
Electric Connection REAR AUX OUTPUT DTV/AUX INPUT AUDIO INPUT (R-CH/RED) VIDEO INPUT (YELLOW) AUDIO OUTPUT (L-CH/WHITE) AUDIO INPUT (L-CH/WHITE) AUDIO OUTPUT (R-CH/RED) SUBWOOFER OUTPUT (GREY) FRONT AUX OUTPUT AUX OUTPUT AUDIO OUTPUT (R-CH/RED) VIDEO OUTPUT 2 (YELLOW) VIDEO OUTPUT 1 (YELLOW) COAXIAL OUTPUT ( BROWN) AUDIO OUTPUT (L-CH/WHITE) RADIO ANTENNA JACK IGNITION SWITCH(B+) MEMORY BACK-UP(B+) GROUND(B-) BROWN RED YELLOW REARVIEW CAMERA TRIGGER WIRE (B+) ORANGE CHOKE BOX EMERGENCY
Remote Control DVD/RECEIVER CONTROL 15 MODE 17 7 2 MUTE PLAY/PAUSE 3 REDIAL ANGLE MO/ST 19 13 22 16 STOP 20 PAIR 1 LOUD MENU EQ CLK LO/DX 21 6 14 23 OSD 24 18 BAND 9 ENTER TITLE/PBC A/PS TOP RPT INT 1 2 3 4 5 6 SEL 7 8 9 SETUP GOTO +10 0 VOL 11 10 4 VOL 1 CLK 2 PAIR/ 3 STOP 4 SETUP 12 RDM 8 Ref # Button 5 27 26 25 Function Press it briefly to view the clock time , Press again to return to normal display mode . Press longer to set the time .
Remote Control Ref # Button 8 GOTO 9 / 10 SEL 11 VOL+/- 12 / / / 13 14 15 Function Press it button to begin playback at a moment in the program you designate. Use number buttons to enter the data that is needed. In Bluetooth menu, it serves as the asterisk button on your mobile handset. Press these buttons to skip ahead or back one track.
Remote Control Function Ref # Button 23 This button is used to confirm selections and settings within ENTER many of the menus in the OSD system. In Disc playback mode, press it to search reverse rapidly 24 25 0-9 Use to input numerical values during programming, with the GOTO button, or to directly select a track to play . 26 +10/ This button is used with the other number buttons for use with two-digit number entries. In Bluetooth menu, it serves as the hash button on your mobile handset.
Basic Operation POWER ON/OFF Press shortly the / MOD button on the front panel to turn on the Player ON, press it longer again to Player OFF . OPEN/CLOSE THE MONITOR AND ANGLE ADJUSTMENT Press OPEN/CLOSE button on front panel , the monitor will draw out automatically . LOADING/EJECTING A DISC LOADING A DISC 1. Press the REL button (1) on front panel , the front panel will flip down . FIG.1 2. Insert the disc with printed side facing up into the disc slot . 3.
Basic Operation TFT Monitor Adjustment Do not rotate the monitor forcibly to avoid mechanical damage . In any modes, touch the screen of “ ” range to enter the main menu . Touch the SET ICON to enter the setting menu, the message display in the screen: FIG.4 Return the monitor to the central viewing position, then press CLOSE button on the front panel , the monitor will turn downward automatically . Contrast Color Tint FIG.
Basic Operation TINT: 0 to 32 Adjust the tint if the human skin color is unnatural. -Adjustable when “NTSC “ is selected for “NTSC/PAL “ . ADJUSTABLE ITEMS: TREBLE: -14 to +14 Adjust treble level . BASS: -14 to +14 Adjust bass level . ANIMATION (optional) Change the playing time of animation among of “10SEC, 30SEC, 60SEC, 90SEC, 1MIN, 2MIN, 3MIN, 4MIN and OFF ”. (Please note: please set the time to “10SEC” for the first, when you turn the unit on .
Basic Operation ALTERNATE AUDIO/VIDEO SOURCE Setting the time In SETTING mode, touch the “TIME” range to select the time mode . Hour Minute 12H/24H 36 VOL+ VOL - Touch the “ TIME ” section on the setting menu, touch the “ / ” ranges to select the adjustment item, touch the “ / ” ranges to adjust the selectment item , It`s depend on your need to setup the data . On the front panel of the unit , there is an AUX IN jack, to connect analogue replay devices.
Control Panel FRONT VIEW CLOSED POSITION 8 17 18 20 19 7 5 14 OPEN/CLOSE 1 REL CH 1-6 IR MIC RESET 12 ST INT RPT RDM PAIR SEL 3 EQ 15 CH MU PAIR AUX IN BND VOL+ 16 CAR DVD/VCD/CD/MP3 PLAYER WITH MPEG4 DVD VCD CD MP3 MPEG4 LUD LOC EON APS NO DISC IN 13 MOD VOL- 2 4 11 21 6 9 10 1. REL BUTTON Press the button to flip down the front panel, then you can insert the CD disc into the CD compartment . Also you can press the Eject button to eject disc . 2.
Control Panel 5. EQ BUTTON Press briefly the EQ button to turn to equalization function and to select desired audio mode. There are five kinds of mode as below: JAZZ CLAS POP ROCK FLAT Press and hold (more than 2’s) the EQ button to switch the Loudness function ON and OFF . 6. APS BUTTON Automatic Memory Function: In Radio mode, press longer (more than 2’s) the APS button to active automatic station storage. The radio searches within the current frequency band, e.g.
Control Panel 9/10. / BUTTONS (TUNE, SEEK, TRACK, SKIP UP/DOWN) A) In DISC, USB mode: if you wish to jump forwards or backwards press shortly the / button . To wind go the tracks pressed and keep (more than 2’s) the or button . FF X2 appears in the display. Operating it again, the speed of rapid forward or reverse changes according to the disc as follow: Normal Playback 2x 4x 8x 20x DVD/VCD/CD/MP3: B)In Radio Mode: press shortly the or to set a radio station manually.
Control Panel 20. OPEN/CLOSE Press the button to open/close the monitor . 21. LCD Display FRONT VIEW OPEN POSITION CLOSE 3 4 2 1. 1 TFT Display (liquid crystal display) The operation of the TFT, please see page 14. 2/3. / Adjust the screen viewing angle of the operating unit . 4. CLOSE Press the button to close the monitor .
Touch Screen Operation In any modes, touch the “ ” ICON on the touch screen to enter the main menu, the information will display : Selecting The Frequency Band Touch the screen of “ BAND ” section repeatedly to select the band , the message will show in turn : FM1 FM2 FM3 AM1(MW1) AM2(MW2) LCD display on the front panel will display as below : ST FM3 87.50 1 2 3 4 FM3 BAND The touch buttons on the lower of the touch monitor: 1. Power button in any modes, touch the “ ” ICON to switch the unit off .
Touch Screen Operation - Store in Memory >Select the frequency band >Select the station (by touching the / ICON .) >Keep the desired memory key pressed in until the station is heard again after a brief interruption . - Retrieve a preset station Touch the 1-6 ranges briefly to retrieve a station which had been stored in the memory in advance the chose number is shown on display .
Touch Screen Operation DVD MODE In any modes, touch the screen of the “ ” ICON to enter the main menu , then touch the DVD ICON on the main menu to enter the DVD play mode . The message will display as below : (When Parking Brake supplied .
Touch Screen Operation Basic Operation Use the direction keys ( / / / on remote control to move the enlarged picture . Stopping Play Touch the screen the range to stop the unit playback. touch the range to start play. Selecting The Play Modes During the Disc playback, touch the “RPT, RDM, INT ” range to select the different playing mode . Pause (still picture) Touch the “ ” section on touch screen during playback will stop play temporary, touch it again to return the normal playback . 1).
Touch Screen Operation 3). INT Function FOR VCD (With PBC OFF): FOR CD : Touch the screen of the “INT” section (or longer press the 3/INT button on the remote control ) to play the previous 10 seconds part of each track/chapter on disc. (Touch it again to cancel this mode) Touch the screen the of “GOTO” range , the screen will display the following message : VCD TRK 01/19 PBC ENTER FOR VCD : Touch the screen of the “INT” section (or longer press the 3/INT button on the the remote control ).
Touch Screen Operation ON-SCREEN DISPLAY FUNCTION OSD 2.Example for VCD/SVCD/CD: During playback, touch the screen of the OSD section, it will display the following as below : A.Touch or Press OSD for first time: VCD TRK 1/19 1. DVD: A.Touch or Press OSD for first time: VCD TRK 1/19 Title Number, Total Title Number, Chapter Number, Total Chapter Number of this Title of the disc currently being played will be shown on the screen, along with the elapsed time. B.
Touch Screen Operation DVD/VCD Special Function 3. Multi-Angle Function (for DVD Only) During DVD playback, touch the ANGLE ( ) button on the touch screen . 1. Multi-subtitle Language Function (for DVD Only) During DVD playback. Touch the SUBTITLE section on touch screen(or press the SUBTITLE on the remote) . Each time the button is pressed or touch, number of the subtitle language changes in sequential order. Notes: - The language number is different according to the disc.
Touch Screen Operation SYSTEM SETUP SETUP USING THE MENU SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT NTSC PAL AUTO EXIT EXIT 1. Touch the screen of “ SET ” range or press the SETUP button on remote . 2.The SETUP menu is displayed. 3.Touch directly the desired item to select the preferred item . Or by using the / / / buttons . 4.
Touch Screen Operation SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT SYSTEM SETUP TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT 4:3PS 4:3LB 16:9 EXIT 16:9 ----- EXIT 4:3 Letter Box 4:3 Pan Scan TV DISPLAY SETUP This is to select the appropriate TV aspect (4:3 or 16:9) according to the connected TV set. Normal/PS (For 4:3 TV) Played back in the PAN & SCAN style. (If connected to wide-screen TV, the left and right edges are cut off.
Touch Screen Operation SYSTEM SETUP LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG TV SYSTEM SCREEN SAVER TV TYPE PASSWORD RATING DEFAULT RESTORE EXIT ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN EXIT DEFAULTS Selecting the DEFAULT item and confirming RESTORE will return ALL personal settings you have made, including radio and TV presets, to the factory default settings.
Touch Screen Operation VIDEO SETUP LANGUAGE SETUP OSD LANGUAGE AUDIO LANG SUBTITLE LANG MENU LANG these settings allow you to set the video signal brightness, contrast, hue, and saturation . ENGLISH GERMAN SPANISH FRENCH PORTUGUESE ITALIAN RUSSIAN VIDEO SETUP 12 10 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS EXIT DISC MENU LANGUAGE SETUP Select the preferred DISC MENU language by touching directly the desired language .
Touch Screen Operation VIDEO SETUP VIDEO SETUP +6 +4 +2 0 -2 -4 -6 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS 8 6 4 2 0 BRIGHTNESS CONTRAST HUE SATURATION SHARPNESS EXIT EXIT HUE- the hue of the video signal (the color of the pictures) . SHARPNESS- the sharpness of the video signal (the image setting acumination) .
Touch Screen Operation AUX Operation This unit features AUX IN line input jacks on both the front (headphone type) and rear (RCA type ) panel . follow the diagram below to connect analogue replay devices. Use this jack to replay sound of other replay equipment such as DVD players, computers, etc. Via the loudspeakers. 1). Please connect the external device with stereo jack plug the Aux in socket . AUX IN JACK FRONT PANEL AUX IN RE SE T MOD FLAT SWF LOUD AUX 1 LOUD EQ VOL+ VOL - 3).
Touch Screen Operation Bluetooth Operation the function of blue-tooth about the unite . 1. “Pair” To Your Bluetooth Phone LCD display on the front panel will display as below : Prior to using the Car Kit for the fist time, you must pair it with a Bluetooth-enabled mobile handset. The following steps describes pairing the instruction for a typical Bluetoothenabled mobile handset. DVD 0--0:00:01 ICON remain solid 1). Place the Car Kit and mobile handset in 3 meters apart. 2).
Touch Screen Operation Note: When you dial the wrong number, you can touch the screen “ ” to delete the wrong number . (You can also press the “ ” button on the remote control to do so .) Please note : “ ” and “ ” serves as the “ ” and “ ” button on your mobile handset . Answer a call After you hear the ring tone, a incoming telephone number will display on the TFT monitor . Touch the screen of “ ” range to listen or press the “PAIR/ ” button shortly on the front panel .
Touch Screen Operation USB Operation Following the diagram below, connect your USB device to the front panel USB port . If it is properly connected, the device will be mounted and start playing automatically. Changing From DISC to USB Playback Modes If the disc present in the player is an DVD or VCD or MP3/WMA or MP4 disc, touch the screen of the “MAIN” range to enter the home menu, then touch the “USB” ICON to enter the USB mode .
Touch Screen Operation SD/MMC card OPERATION The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are stored into SD and MMC memory card . Please read below before you start the operation of memory card . Inserting and removing a SD or MMC card on the front panel of unit . Inserting the SD or MMC card . Label side facing upward Press the REL button to flip down panel and Insert the memory card into slot with label side facing upward .
Touch Screen Operation MP3/WMA/JPEG/MPEG4 DISC PLAY When you insert a disc which contains MP3, WMA or JPEG files, the different file types are detected, and a list of the files are produced, as shown in the diagram below. 2 3 1 Current type (highlighted bar) . [007] ITLE / SONG: 1 TRACK 03 / 2 Current track (highlighted bar) . 001 \ 002 003 MP3 3 Current text (ID3 TAG display). 004 WMA 005 784 006 4 The current play mode(MP3). 007 008 5 Select the play mode(JPEG).
Specification Generall : Supply Voltage: Current Consumption: Signal System: Discs Played: 12V DC (11V-15V) Less than10 A Compositive video 1.
Trouble Shooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. SYMPTOM No power CAUSE SOLUTION The car ignition switch is not on The fuse is blown If the power supply is properly connected to the car accessory terminal,switch the ignition key to "ACC" Replace the fuse Presence of disc inside the Remove the disc in the player, then put a new one player.
