MONROC USER MANUAL UM_EN Date: 140324 R
CONTENT MONROC CONTENT...................................................................................................................................................................... 2 SYMBOL DESCRIPTION........................................................................................................................................ 4 Hazard intensity levels...........................................................................................................................................
CONTENT MONROC Cleaning the gasket and shower plate........................................................................................................................... 21 Additional handling of the machine................................................................................................................................ 22 STORAGE AND DISPOSAL OF MACHINE.......................................................................................... 22 How to store the machine................
SYMBOL DESCRIPTION MONROC Hazard intensity levels There are three different levels of hazard intensity, identified by signal words DANGER, WARNING and IMPORTANT. The level of hazard is determined by the following definitions. Observe the statements to ensure safety, performance, prevent injury and machine damage. Important: Alerts against unsafe practices. Observe to ensure drink quality, machine performance, food safety, to prevent minor personal injury or damage to the machine.
GENERAL MONROC Introduction Thank you for choosing a MARKUS espresso machine. We hope you enjoy it ! Read the user manual before using the machine. This manual contains important instructions on intended and safe use of the coffee machine. eep this manual close to hand for future K reference. If damaged or lost, request a copy from the manufacturer. General instructions Machine installation and certain maintenance operations should only be performed by qualified service personnel.
GENERAL In case of emergency, (e.g. the machine catches fire or becomes unusually hot or noisy), disconnect the power immediately and close the water inlet tap. If the machine is not going to be used for a prolonged period of time, disconnect the power. When disconnecting the power, pull the plug rather than the cable. When packed for storage, keep the machine in a dry place with an ambient temperature of over 5ºC. Boxes may be stacked in piles of up MONROC to three units of the same model.
TECHNICAL SPECIFICATIONS MONROC MONROC 1GR MODEL SPECIFICATIONS MINI 1GR CONTROL MINI 1GR PULSER Steam wand 1 unit Hot water outlet 1 unit Temperature control PID regulation Pressure switch Temperature control by group No Programmed via display No Dispensing system for tall cups Optional Energy saving mode No Height, width, depth (mm) 430, 460, 530 430, 460, 530 Boiler volume (L) 6 (L) Power supply 230V 1N~ 2770 W 50/60 Hz Water connection 230V 1N~ 2780 W 50/60 Hz Female 3/8" th
TECHNICAL SPECIFICATIONS MONROC MONROC 2GR MODEL SPECIFICATIONS PULSER 2GR CONTROL 2GR Machine model, Standard - EBEE-D32B-12AI 220-240V 1N~ 3350W Machine model, Take Away - EBEE-D32B-22AI 220-240V 1N~ 3350W Steam wand 1 unit Hot water outlet 1 unit Temperature control Pressure switch PID regulation Temperature control by group Yes Programmed via display No No Dispensing system for tall cups Optional Energy saving mode Yes Height, width, depth (mm) Yes 430, 650, 530 Boiler volum
OVERVIEW OF COMPONENTS MONROC Front view of the machine MONROC 1GR 9
OVERVIEW OF COMPONENTS MONROC Front view of the machine MONROC control 2GR Boiler manometer Water tap Dispense buttons Steam tap Power switch Steam wand Element light Porta-filter Hot water outlet Brewing group Brewing group MONROC pulser 2GR Boiler manometer Water tap Dispense buttons Steam tap Power switch Steam wand Element light Porta-filter Hot water outlet 10 Brewing group Brewing group
DIMENSION SKETCH MONROC MONROC 2GR A D B Model C A B C D(Min) D(Max) MONROC control 2Gr 480 mm 660 mm 540 mm 74 mm 124 mm MONROC pulser 2Gr 480 mm 660 mm 540 mm 74 mm 124 mm 11
TRANSPORT MONROC Packaging The machine is shipped in a unique carton box which uses expanded polystyrene paddings. The machine box is provided with conventional symbols that can be perfectly visible during the handling and storage tasks. The machine box must stay in a vertical position during the transport. Do not tip or try to place the box tilted sideways in any way. During transportation the box must be protected from hits, impacts, shocks and exposure of bad weather elements.
INSTALLATION MONROC Electrical installation The coffee machine should only be connected to the power supply by qualified personnel. The following safety instructions should be followed at all times: Check that the electrical specifications on the ratings plate match the specifications of the power supply at the point of installation. The coffee machine must be connected to an earthed socket that complies with the regulations in force in the country of installation.
INSTALLATION MONROC Water connection The Installation of the machine to a water mains connection must be done by a qualified person. Rinse around 20 liters of water from the main water supply before connecting the machine to the water connection. Connect the inlet hose that is assembled in the machine to the main water supply, which should have a 3/8” male connection fitted with a shut-off valve, tighten it with a wrench.
INSTALLATION MONROC The porta-filter set Lock-in spring (filter basket) Filter basket Placing porta-filter spring Porta-filter and filter basket for single espresso (7g) Porta-filter & filter basket for double espresso (14g) Inserting the porta-filter in the group Align the porta-filter's two lateral flanges with the slots in the group. Porta-filter not fully inserted. Insert the porta-filter and rotate it anti-clockwise until the handle is perpendicular to the coffee machine.
OPERATION MONROC Espresso brewing 01 02 Important: Always keep the porta-filter inserted in the group to keep it warm. This is very important to maintain an optimal temperature to get the best espresso. Unlock and remove the porta-filter from the group head. 03 04 Fill the filter basket of the porta-filter with espresso powder (the amount may differ depending of the filter basket size). For best result use freshly ground espresso beans. 05 Press down the coffee with the coffee tamper.
OPERATION MONROC Steaming and frothing milk Steaming Frothing 01 Place the steam wand over the drip tray and open the steam tap for a few seconds, this will allow condensed water to be ejected. Close the steam tap when only steam comes out. 02 I mmerse the steam wand into the jug containing the milk, make sure the wand tip is submerged. 03 Open the tap again to start heating or frothing the milk. WARNING! 04 Once the milk reaches the desired temperature, close the tap and remove the jug.
OPERATION Hot water dispensing Machines with manual water tap Place a jug (or similar) under the hot water outlet Open the hot water tap. Close the tap as soon as the machine has dispensed the desired amount of water. WARNING! Never expose hands and fingers directly under the water outlet during operation to avoid scalding or serious burns.
CLEANING AND MAINTENANCE MONROC Coffee machine cleaning Important: o obtain the best efficiency, quality and performance of the machine, you should always T follow the cleaning and care instructions provided in this manual. Turn off the power switch when cleaning the exterior of the machine. All external surfaces should be cleaned with a wet cloth that will not get out fibers, threads or scratch the machine. Do not use aggressive cleaning detergents, solvents or degreasers.
CLEANING AND MAINTENANCE MONROC Cleaning the Brewing group and porta-filter Unlock and remove the porta-filter from the group head. Place the cleaning membrane in the filter basket. Fill the filter basket with professional cleaning powder for espresso coffee machines. Lock the porta-filter into the group head. Activate the auto-cleaning program: Turn off the machine. Press and hold down the 2 Short Espressos button on the button panel of the group requiring cleaning.
CLEANING AND MAINTENANCE MONROC Cleaning the gasket and shower plate Cleaning the gasket When placing the porta-filter filled with grinded coffee into the brewing group, left overs will accumulate in the closing surface. If these remains are excessive it can prevent a good closing between the porta-filter and the group head.Moreover, these remains can even block the dispensing of water through the group head.
CLEANING AND MAINTENANCE MONROC Additional handling of the machine Important: Avoid placing wet cups directly on the cup shelf, it may drip into the machine and cause machine damage. Remove and insert the porta-filter gently. Never use excessive force to try to close the porta-filter. STORAGE AND DISPOSAL OF MACHINE How to store the machine Make all the cleaning procedures described in this manual. Disconnect and roll up the power cord. (this should be performed by a qualified person).
PROGRAMMING MONROC Buttons functions Here is some of the additional functions that the electronics offers: Volume control of four different espresso drinks per brewing group. Time-controlled hot water dispensing. (if available) Automatic filling and level control of the boiler. Automatic switch off of the heating element if not enough water. System supervision through alarms. RS-232 serial interface with reader for connecting control panel and computer. Automatic cleaning of the brew groups.
PROGRAMMING MONROC Programming the coffee dosage This section explains how to program the doses dispensed automatically by the drink buttons. Important: Use a porta-filter filled with fresh coffee for every new dose you program. On machines not equipped with a display, hold down the Continuous Dispensing button for 4 seconds. On machines equipped with a display, hold down the Continuous Dispensing button for 8 seconds. The Continuous Dispensing button light will flash.
PROGRAMMING USING THE DISPLAY MONROC Machine status Machines equipped with a display include the following additional functions: Automatic daily on/off timer (stand-by function). Clock settings (current time and date). Promotional display. Number of coffees/infusions dispensed. Digital boiler-temperature display and control. PID-technology boiler-temperature control. Programming and settings help system. Visual water-softener regeneration alarm. Display language selector.
PROGRAMMING USING THE DISPLAY MONROC Accessing the second menu level Doses setting Select within 30s fig. 06 Set clock fig. 07 With the machine on, press the Continuous Dispensing button on the Left-hand drink buttons and hold it down (for over 8 seconds) until the dose-programming menu is displayed. All the drink buttons lights will be turned on and the Continuous Dispensing button light will flash. The display will be as shown in fig. 06.
PROGRAMMING USING THE DISPLAY MONROC Auto On/Off Auto On/Off On: hh.mm fig. 9 Espressos button to accept it. Set the values for the minutes in the same way( and , ). Note: i By default, this setting is set as: On: - - : - - (indicating that the function is disabled). Changing the value to anything other than - - : - - enables the function. To leave this function disabled, press the 2 Short Espressos button whilst the value selected is - - : - -. Auto On/Off Off: hh.mm fig.
MULTIBOILER MODELS TEMPERATURE CONTROL MONROC Digital thermostat status If you have a multi-boiler machine, it will have a digital temperature control which is independent for each brewing group. There are following types of multi-boiler machines: 2 groups with 3 boilers. 3 groups with 4 boilers. The temperature control is performed by a PID thermostat, which get an unbeatable temperature output stability and control. KEYPADS CURRENT GROUP TEMP.
MULTIBOILER MODELS TEMPERATURE CONTROL MONROC Adjusting group temperature To adjust the temperature for each group, proceed as follows: With the main switch on and the thermostat in normal mode: fig. M Press briefly the button “ ”. The thermostat will show the message “PrG” on the display. (See fig. M) Immediately, press briefly the button “ ”, the display will show the setting temperature “set point”. (See fig. N) fig. N Increase ( ) or decrease ( through the buttons.
MESSAGES AND ALARMS Flow meter Gr. X Time-out alarm Boiler filling up Probe unconnect Service 999999999 Change filter 999999999 MONROC Fault in flow meter X / Flow fault detected in counter X Check that the machine is receiving water. Temperature sensor fault Service the machine. To disable the alarm and reset the counter: Turn off the machine. Simultaneously press and hold down the 1 Short Espresso and 1 Long Espresso buttons. Turn on the machine. Regenerate the filter.
TROUBLESHOOTING MONROC The following checks can be carried out by users once the machine has been turned off and disconnected from the power supply. For all other non-specified machine faults, disconnect the machine from the power supply and immediately contact authorised and qualified service personnel. Problem Possible cause Solution The plug is not correctly inserted into the power socket Check that the plug is correctly inserted and that the power socket is operational.
For the warranty to be valid the conditions for maintenance must have been followed according to our instructions, proper precaution has been made and warranty claim been issued without delay. The affected equipment may not be used during awaiting service if there is any risk that the damage or defect would worsen.
