Instruction manual and maintenance MONROC U / GB ............................................................................... ............................................................................... Rev.
1. Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 11.1 11.2 12. 13. 14. 15. 16. 17. 18.
2. Identification of external components FIG. 1 MONROC 3. Water tap 5. Electronic control panel 2. Boiler pressure gauge 1. Steam tap 12. Exit steam spout 6. Indication lamp 7. Adjustable leg 8. General switch 11. Hot water exit 9. Filter holder 10. Brew group 3. Characteristics Model Number Unit 2 Units 2 Measurements in mm. Width depth height 650 530 480 Boiler Litres Power (W) Resistance 11.5 3050 3. Total 3235 Voltage Vac Weight Kg.
. Equipment provided MONROC For models: Units 2, 3 and 4. 2 complete filter holders for two cups + 1 filter holder for 1 cup. + 1 1/2 meter hose. + 1 clean unit filter. 5. Installation of the coffee machine MONROC When the machine is installed in its case, the latter must be as near horizontal as possible (use the adjustable legs) so that the coffee issuing from the machine is evenly distributed between the cups.
6. Refilling water in the boiler MONROC Water is refilled automatically. 7. Pressure gauge MONROC Indicates pressure in the interior of the boiler Pressure-Temperature Relationship Temperature (ºC) 125 120 115 110 0,6 0,7 0,8 0,9 1 1,1 Pressure bars 8. Start up MONROC 1. Open the water screw valve external to the machine. 2. Connect the general switch, see (8) Fig. 1-. 3. Open the steam tap until steam is emitted. ”The red pilot light, see (6) Fig.
9. Fitting the filter holder into the dispensing unit MONROC Water is refilled automatically. FITTING THE FILTER HOLDER INTO THE DISPENSING UNIT The filter holder has two projections on the sides which must be fitted into the unit’s slots. When that has been done, turn from left to right until the handle of the holder is at a perfect right angle to the coffee machine. FIG. 2 CORRECT POSITION OF THE HOLDER IN THE UNIT FIG. 3 CORRECT 10.
10. Dispensing coffee MONROC CONTROL MODEL a) b) c) d) Pull the filter holder away from the machine. Place the amount of coffee you need for coffee of your choice in the filter. Preferably, the coffee should have been recently ground. Use the appropriate filter holder See Fig. 3-. Push the coffee down with the coffee press. Select the desired option from the electronic control panel.
11. Electronic control panel MONROC 11.1. Programming the electronic control panel Keep pressing the continuous button, on either of the two control panels, for 8 seconds. The continuous coffee lights will blink on and off. Press the coffee dose you want to reprogramme (1 espresso - 1 large coffee - 2 espresso 2 large coffees). It will then begin to dispense coffee. When you have reach the desired dose, push the dose you selected once more to end the process, and the dose will be remembered.
11. Electronic control panel MONROC 11.2. Electronic control panel alarms When the electronic control panel detects a lack of water in the boiler, the five lights on the control panel will blink. When the volume meter on the electronic control panel detects a problem, the light for the dose which we have pressed blinks. Maximum security period. All doses have a maximum coffee dispensing time of five minutes. 12.
14. Cleaning the coffee machine MONROC Cleaning the coffee machine Disconnect the machine for cleaning. The entire surface of the coffee machine can be cleaned with a damp cloth. Use NON-aggressive detergents. Do not use solvents or degreasing agents. 15. Cleaning the dispensing unit MONROC Cleaning the dispensing unit a) b) c) d) Pull the filter holder away from the machine. Place the filter membrane inside the filter holder, -see Fig. 6-. Place a sachet of detergent inside the filter holder.
16. We recommend MONROC We recommend · The unit must be cleaned every day without using detergent, only with the membrane and water. · The unit must be cleaned with detergent once a week. Depending on the hardness of the lime, decalcify. Use freshly ground coffee to preserve the aroma and taste of the coffee.
17. Possible dysfunctions MONROC Possible dysfunctions These malfunctions are caused by lime: - 18. The coffee does not emerge at the right temperature: The exit tubes of the exchangers are obstructed by lime. Water fails to issue from the brew groups: Precautions MONROC Precautions When brewing a coffee, never take the filter holder out. Hot water under pressure can cause serious scalding. Never handle anything inside the machine. Only qualified authorised personnel may do so.
FOR SERVICE Your retail dealer ............................................................................... ............................................................................... ............................................................................... CREM International AB Box 960, 671 29 ARVIKA, Sweden Tel: +46 (0)570-477 00, Fax: +46 (0)570-47719 E-mail: info.se@creminternational.com www.creminternational.com Art. nr/Art. no.