User Manual

6 5
Die EX-1311-2 ist ein Modul zur Umsetzung von USB 2.0 auf eine RS-232 Schnittstelle mit
FIFO 16C550 Port für den Anschluss von High Speed Seriellen RS-232 Peripherie Geräten
(z.B. Modem, Plotter usw.). Die EX-1311-2 ist mit einem USB 2.0 A-Stecker zum Anschluss an
den PC und einem RS-232 seriellen 9 Pin Stecker ausgestattet. Das USB Modul ist Hot Plug &
Play fähig. Für die Einstellungen der I/O Adressen und Interrupts sind keine Jumper und Ein-
stellungen notwendig, da die Einstellungen automatisch vom System BIOS und bei der Installa-
tion des Betriebssystems vorgenommen werden.
Kompatibilität: USB 1.1 & 2.0
Betriebssysteme: Windows 9.x/ ME/ 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux/ MAC
Anschlüsse: 1x USB 2.0 A-Stecker, 1x 9 Pin Stecker Seriell RS-232
Lieferumfang: EX-1311-2, Treiber CD, Anleitung
Zertifikate:
1
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Anleitung
Vers. 1.0 / 01.11.17
EX-1311-2
ANSCHLÜSSE & STATUS LED‘S
USB 2.0 A-Stecker
zum Anschluss an PC
S1: 9 Pin Stecker Seriell RS-232
2x Sechskantmuttern
9 Pin Stecker Seriell RS-232
Pin Signal Pin Signal
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 GND
DB 9M
Verdrahtung RS-232
DB9 (EX-1311-2) RS-232 (Endgerät)
1 DCD 1 DCD
2 RXD 2 RXD
3 TXD 3 TXD
4 DTR 4 DTR
5 GND 5 GND
6 DSR 6 DSR
7 RTS 7 RTS
8 CTS 8 CTS
RS-232 Anschlussbelegung:
HARDWARE INSTALLATION
Because there are large differences between PC’s, we can give you only a general installation
guide for the EX-1311-2. Please refer your computers reference manual whenever in doubt.
1. Connect the EX-1311-2 USB to the USB A-Port at the your PC.
2. If you would like to screw the serial cable to the 9 Pin connector of the EX-1311-2, then
unscrew the screws (see Picture 1) and screw the supplied hexagon nuts into the holes on
the EX-1311-2 (see Picture 2). Now you can attach the serial cable to the EX-1311-2.
CLEANING
For cleaning please use only a dry fluff less cloth and remove the dirt with gently pressure. In
the area of the connectors please make sure that no fibres from the cloth remain in the connect-
ors. Attention! Never use a moist or wet cloth for cleaning!
CONNECTORS & STATUS LED‘S
USB A-Plug:
USB 2.0 A-Plug
Pin Signal Pin Signal
1 VCC 3 DATA+
2 DATA- 4 GND
Picture 1 Picture 2
Remove the Screws Insert the Hexagon Nuts
3. When you are ready you can start your PC and continue with the point „Driver Installation“.
Status LED‘s:
RXD
TXD
DRIVER INSTALLATION
Windows
After the hardware installation Windows will recognize the device automatically and install the
drivers. If the driver shoul not be installed automatically, please insert the Driver CD into your
CD-Rom drive (e.g. Drive D:) and open the folder „USB_to_IO/FTDI“. Please select the folder
with your operating system and install the driver (see Picture). Follow the hardware assistant
and finish the installation. Important! Restart your PC in any case after installing the drivers.
CHECK INSTALLED DRIVER
Open the >Device manager<. Now you should see at „Ports (COM & LPT)“ and „USB-
Controller“ the following new entry:
If you see this or a similar information the device is installed correctly.