USB 3.
CONTENTS INTRODUCTION ....................................................................................... 3 FEATURES .......................................................................................... 3 SYSTEM REQUIREMENTS .................................................................. 3 SUPPORTED COMMON DISPLAY RESOLUTION: ............................... 4 NOTES ................................................................................................ 4 TECHNICAL SPECIFICATIONS: .......
USER MANUAL INTRODUCTION Thank you for purchased the USB 3.0 DISPLAY ADAPTER. By 10 times faster than USB 2.0, the USB 3.0 DISPLAY ADAPTER provides a unique solution to add an extra display for your computer just plug and play. It works as external video card which allows adding an additional display instantly without hassle of open the computer chassis to install the internal graphics card. The connected display can act as mirrored or extended desktop of the main display on your computer.
USER MANUAL SUPPORTED COMMON DISPLAY RESOLUTION: Aspect Ratio Resolution Color Depth 16:9 2048 x 1152 16,32 bits 16:10 1920 x 1200 16,32 bits 16:9 1920 x 1080 16,32 bits 16:10 1680 x 1050 16,32 bits 16:9 1600 x 900 16,32 bits 16:10 1440 x 900 16,32 bits 16:9 1366 x 768 16,32 bits 16:9 1360 x 768 16,32 bits 16:10 1280 x 800 16,32 bits 15:9 1280 x 768 16,32 bits 16:9 1280 x 720 16,32 bits 4:3 1600 x 1200 16,32 bits 4:3 1400 x 1050 16,32 bits 5:4 1280 x 1024 16,32 b
USER MANUAL TECHNICAL SPECIFICATIONS: Operating System Host Interface Video Output Connector Windows 7 / XP (32bit &64bit) Mac Snow Leopard / Lion USB 3.0 A type connector Cable length:17±1cm connected DB- 15pin (female) – Model: USB3.0 -VGA HDMI (female) – Model: USB3.
USER MANUAL INSTALLATION ON WINDOWS 7 DEVICE DRIVER INSTALLATION Installing the device driver enables your computer‟s operating system to recognize the USB 3.0 DISPLAY ADAPTER once it‟s connected. Please check your operating system and refer to the appropriate installation procedure to begin installing the device driver. This section illustrates the simple device driver installation procedure for computer running Windows 7 operating system. Please make sure the USB 3.
USER MANUAL Step 3. License Agreement; please review it and check “I accept the terms of the license agreement.” Click “Next” to accept the License Agreement. Step 4. Setup is searching for installed features..... *You may notice there a screen flashes during hardware installation. It is part of the normal process.
USER MANUAL Step 5. Select “Yes, I want to restart my computer now”, and click “Finish” to reboot. Step 6. HARDWARE DEVICE DRIVER INSTALLATION After reboot, please connect the external display device (monitor/projector) to the VGA/HDMI connector of USB 3.0 DISPLAY ADAPTER and turn on the display device. Then plug the USB 3.0 DISPLAY ADAPTER into an available USB 3.0 port of your PC or Notebook. The device driver software setup will begin automatically.
USER MANUAL Step 7. INSTALLATION OF MULTIPLE USB 3.0 DISPLAY ADAPTERS Please plug the additional USB 3.0 DISPLAY ADAPTER into the available USB 3.0 port of your PC or Notebook. The system will automatically start the installation procedure and the prompt message will pop-up on the task bar. The device driver software was installed properly. To make sure the USB 3.0 Display Adapters worked correctly, please reboot the computer after finished the installation.
USER MANUAL After reboot the computer, the USB extended display will be shown on the attached display device.
USER MANUAL VERIFYING DEVICE DRIVER INSTALLATION (WINDOWS 7) The following procedure allows you to verify the device driver installation. Please right click “Computer” → “Properties” → “Device Manager”. Plug-in the USB 3.0 DISPLAY ADAPTER, then double click “Universal Serial Bus controllers”. Begin verification by make sure highlighted devices were added to the system. Single USB 3.
USER MANUAL Single USB 3.
USER MANUAL Multiple USB 3.
USER MANUAL DEVICE DRIVER UN-INSTALLATION Step 1. Access Program Uninstall: Click “Start” →“Control Panel” →“Programs”. Click “Uninstall a program” Look for “ USB External Graphics Family 11.xx.xxxx.0179” (driver version). Click “Uninstall” button. Step 2. Unplug the USB 3.0 DISPLAY ADAPTER and click “OK” to continue. Step 3. Select “Yes, I want to restart my computer now” and click “Finish” to reboot. After reboot, you will complete the driver un-installation.
USER MANUAL INSTALLATION ON WINDOWS XP DEVICE DRIVER INSTALLATION Installing the device driver enables your computer‟s operating system to recognize the USB 3.0 DISPLAY ADAPTER once it‟s connected. Please check your operating system and refer to the appropriate installation procedure to begin installing the device driver. This section illustrates the simple device driver installation procedure for computer running Windows XP operating system. Please make sure the USB 3.
USER MANUAL Step 3. License Agreement; please read it and select “I accept the terms of the license agreement.” Click “Next” to accept the License Agreement. Step 4. Setup is searching for installed features….. ※ You may notice the screen flashes during hardware installation. It is part of the normal process. ※ When the Microsoft Windows Security warning dialogue box appears, please select “Continue Anyway” to continue with the installation.
USER MANUAL Step 5. Click “Finish” to complete the software installation. Step 6. HARDWARE DEVICE DRIVER INSTALLATION 1. Please connected the external display device (monitor/projector) to the VGA/HDMI connector of USB 3.0 Display Adapter and switch it on. 2. Then, insert the USB 3.0 Display Adapter into an available USB port of your computer. The device driver will be configured automatically.
USER MANUAL Step 7. INSTALLATION OF MULTIPLE USB 3.0 DISPLAY ADAPTERS Please plug the additional USB 3.0 DISPLAY ADAPTERS into the available USB 3.0 port of your PC or Notebook. The setup process will begin automatically. You may see below notification balloons for each additional. To make sure the USB 3.0 Display Adapters worked correctly, please reboot the computer after finished the installation. After reboot the computer, the device is now installed completely and ready to use.
USER MANUAL VERIFYING DEVICE DRIVER INSTALLATION (WINDOWS XP) The following procedure allows you to verify the device driver installation. Please right click “My Computer” → “Properties” → “Hardware” → “Device Manager”. Plug-in the USB 3.0 DISPLAY ADAPTER, then double click “Display adapters”, and “Universal Serial Bus controllers”. Begin verification by make sure highlighted devices were added to the system. Single USB 3.
USER MANUAL Multiple USB 3.
USER MANUAL DEVICE DRIVER UN-INSTALLATION Step 1. Click “Start” → “Control Panel” → “Add or Remove Programs” Select “ Trigger External Graphics Family 11.xx.xxxx.0179” (driver version). Click “Uninstall” button. Step 2. Unplug the USB 3.0 DISPLAY ADAPTER and click “OK” to continue. Step 3. Select “Yes, I want to restart my computer now” and click “Finish” to reboot.
USER MANUAL After reboot, you will complete the driver un-installation. FUNCTION DESCRIPTION This section describes several friendly functions provided by the USB 3.0 DISPLAY ADAPTER designed to ease your single or multiple USB display experience. A display device described in this section means devices such as CRT, LCD monitor, TV display, and projector... ACCESS USB 3.0 DISPLAY ADAPTER UTILITY Make sure the USB 3.0 Display Adapter is attached to the PC.
USER MANUAL DISPLAY ROTATION 4 options available: “0°, 90°, 180°, 270° under the Extended or Primary display modes. It is a useful function for some rotatable display device. DISPLAY MODES “EXTENDED” DISPLAY MODE (DEFAULT) A default display mode; this feature allows the attached USB Display enabled display device to work as “Extended” display of the on-board screen. The extended working space improves work efficiency.
USER MANUAL adapters may prevent this option from working on some systems. You may disable the other utility program (usually found in the same toolbar located on the bottom right hand corner) to make this function work properly. “OFF” DISPLAY MODE This option disables the video output from USB 3.0 DISPLAY ADAPTER. IDENTIFY MONITORS Easy display identification via a serial number will be showed on the upper right corner of all attached display devices.
USER MANUAL DISPLAY SETTINGS Fast access to the system “Display Settings” . ※You also can press key and tap P to select the display modes on Windows 7. FIXED POSITION It remains the prior setting of display location after restart the computer.
USER MANUAL REGULATORY COMPLIANCE FCC This equipment has been tested and found to comply with FCC 47 CFR PART 15 SUBPART B (Class B) & IC ICES-003. Operation is subject to the following two conditions: • This device may not cause harmful interference • This device must accept any interference, including interference that may cause undesired operation of the device.
