ExtremeWireless™ AP3917i/e FCC/ROW Installation Guide 9035166-02 Published November 2018
Copyright © 2018 Extreme Networks, Inc. All rights reserved. Legal Notice Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice.
Table of Contents Preface......................................................................................................................................... 4 Text Conventions...................................................................................................................................................................4 Platform-Dependent Conventions................................................................................................................................
Preface This section discusses the conventions used in this guide, ways to provide feedback, additional help, and other Extreme Networks publications. Text Conventions The following tables list text conventions that are used throughout this guide. Table 1: Notice Icons Icon New! Notice Type Alerts you to... General Notice Helpful tips and notices for using the product. Note Important features or instructions. Caution Risk of personal injury, system damage, or loss of data.
Preface When a feature or feature implementation applies to specific platforms, the specific platform is noted in the heading for the section describing that implementation in the ExtremeXOS command documentation (see the Extreme Documentation page at www.extremenetworks.com/ documentation/). In many cases, although the command is available on all platforms, each platform uses specific keywords.
Preface Extreme Networks Documentation To find Extreme Networks product guides, visit our documentation pages at: Current Product Documentation www.extremenetworks.com/documentation/ Archived Documentation (for earlier versions and legacy products) www.extremenetworks.com/support/documentation-archives/ Release Notes www.extremenetworks.com/support/release-notes Open Source Declarations Some software files have been licensed under certain open source licenses. More information is available at: www.
1 Overview Features LED Indicators The AP3917i/e is an IP67 rated outdoor Access Point with 802.11ac dual band 2:2 radios. The AP3917 is easy to install, lightweight, and is available in an internal (AP3917i) and external (AP3917e) antenna model. Each model includes 802.11 radios, an IoT radio, and a GPS radio. The antennas are built into the AP3917i while you need to install external antennas or terminators for the AP3917e model.
Overview Figure 1: Top and Side Views of AP3917i 1 IoT/BLE Radio 2 Radio - 5 GHz 3 Radio - 2.
Overview 1 IoT/BLE Radio 2 Radio - 5 GHz 3 Radio - 2.4 GHz 4 Status 5 GE1 (PoE IN) 6 GE2 7 Console/Reset 8 2.4 G - Antenna 1 and 2 9 Vent 10 5G - Antenna 2 11 BLE/802.15.4 Antenna 12 5 G - Antenna 1 LED Indicators Both the Radio LEDs will be Green when they are ON and the LEDs will not have any lights when they are OFF. Blue LED indicates the IoT status.
2 Hardware Mounting and Installation Verifying the Box Contents Positioning the AP for Installation Mounting Brackets Usage Mounting the AP3917i/e to a Wall or Solid Surface Mounting the AP3917i/e to a Pole Mounting the AP3917i/e Using Extension Arm Mounting the AP using the KT-147407-01 bracket to a flat surface Mounting the AP using the KT-150173-01 extension on the KT-147407-01 bracket Installing External Antennas Connecting the AP3917i/e to a Power Source LAN/Console Connections Professional Installati
Hardware Mounting and Installation Positioning the AP for Installation Mount the AP so that the vent side is always down. Insert and crimp a ground wire to the provided terminal. You must provide a 3-inch drip loop on all cables. Use the M4 ground screw assembly, with the star washer, to attach the ground wire’s ring terminal to the back of the AP. The wire should be as close to the AP bottom as possible. Tighten the screw to a torque of 13.0-13.5 in-lbs.
Hardware Mounting and Installation Table 5: Mounting Brackets used with AP3917i/e (continued) Mounting Bracket/ Accessory Wall Install Pole Install Notes KT-147407-01; Bracket; comes with three parts Yes Yes For attaching to a wall or a flat surface, use the bracket part that has two holes on the surface of the metal portion. For attaching to a pole, if the 1axis tilt is not required, attach the pole part of the bracket to the access point.
Hardware Mounting and Installation 4 Attach the AP to the “H” Bracket: a Use four M4 screw assemblies to attach the AP to the “H” bracket on the side as shown. b Tighten the four screws to a torque of 13.0-13.5 in-lbs. 5 Secure the anchors to the wall, then secure the bracket to the anchors. If you are attaching the bracket to anchors: 1 2 3 4 Remove the nut and flat washer, if any from the threaded part of the anchors. Put the bracket over the threaded part of the anchors and up against the wall.
Hardware Mounting and Installation 6 If using #10 screws, tighten them to a torque of 25 in-lbs. If using ¼” screws, tighten them to 45 inlbs.
Hardware Mounting and Installation Figure 4: AP3917e Wall Mount H Bracket 7 Remove the black gland cap and the gasket under it. Then separate the gasket from its plastic cage. 8 Attach the gland parts to the LAN cables and insert the LAN cables into the mating connectors in the AP. Mounting the AP3917i/e to a Pole Note The Pole Mounting Bracket (WS-MBO-POLE01) is sold as a separate accessory (part number 30520). 1 Determine the diameter of the pole. Pole Diameter Cable Clamp Size <= 1" (25.
Hardware Mounting and Installation 3 Attach the AP to the “Pole Mount” bracket using four M4 screws. Tighten the four screws to a torque of 13.0-13.5 in-lbs.
Hardware Mounting and Installation 4 Put the metal band around the pole and insert it into the clamp. Turn the clamp screw clockwise, tightening the band around the pole. 5 Remove the black gland cap and the gasket under it. Then separate the gasket from its plastic cage. 6 Attach the gland parts to the LAN cables and insert the LAN cables into the mating connectors in the AP.
Hardware Mounting and Installation 2 Insert the two large locking screws into the metal bracket holes marked zero. On the threaded end add one flat washer, one split washer, and one hex nut. Turn the nut only a couple of turns on the threads. 3 If you are mounting the other end to a pole, insert the two desired cable clamps and then attach the small bracket end to the pole bracket using four M4 screws. Torque the screws to 12 in-lbs.
Hardware Mounting and Installation 2 If 1-axis tilt is required, use four M6 screws, split washers, and hex nuts to attach the pole bracket to the 1-axis tilt bracket. Before attaching the pole bracket to the tilt bracket, ensure that you follow the steps mentioned in Attaching the AP to a flat surface using the flat part of the bracket and 1-axis tilt bracket to attach the other parts of the KT-147407-01 bracket.
Hardware Mounting and Installation Installing External Antennas 1 Attach the external antenna cables to the Standard Polarity Type-N connectors on the AP3917e. All the antennas can be extended away from the AP using the optional cables. Note Optional:To protect your Type-N, Male-Female external antennas from lightning, use lightning protector ML-2452-LAK1-02R. 2 Place a terminator cap on any antenna connectors that will not be used. 3 When installing the AP, all antennas must be positioned vertically.
Hardware Mounting and Installation LAN/Console Connections The AP3917i/e has one LAN (Ethernet) port and a Console port. Refer to Features on page 7 for the location of these ports. During administration and maintenance through the LAN or Console, the AP must still have a power connection through an Ethernet PoE cable.
Hardware Mounting and Installation 2 Slide the claw and seal onto the RJ45 cable (shown below). 3 Plug the RJ45 cable into the port (shown below). Caution Do not run the network cable through the cable conduit connector used for connecting the power cables. You must connect the network cable and power cables through separate connectors. 4 Slide the seal and claw into the main body (shown below).
Hardware Mounting and Installation 5 Secure the seal nut onto the main body (shown below). 6 Tighten the assembly by hand. Tighten the cap to 5 inch-pounds (shown below). Note There should still be some visible threads after you torque in the cap. Professional Installation Instruction Installation personnel This product is designed for specific application and needs to be installed by a qualified personnel who has RF and related rule knowledge.
Hardware Mounting and Installation Instructions d'installation professionnelle Installation Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.
3 Specifications Table 6: Specifications for the AP3917i Item Specification AP Part Number: 31050 WS-AP3917i-FCC AP Part Number: 31051 WS-AP3917i-ROW Enclosure material Cast aluminum base with outdoor rated plastic cover Power source Power is provided by Power-over-Ethernet 802.3af/at. Antenna Five internal single band locked antennas with one internal antenna that can operate as Bluetooth (BLE). Uplink interface Two 10/100/1000 Ethernet ports with PoE.
Specifications Table 7: Specifications for the AP3917e (continued) Item Specification Relative humidity (% RH) 0% to 95% (non-condensing) ExtremeCloud™ Yes enabled ExtremeWireless™ AP3917i/e FCC/ROW Installation Guide 26
4 Regulatory Information Safety Guidelines FCC Declaration of Conformity Statement FCC Radiation Exposure Statement Industry Canada Notice European Waste Electrical and Electronic Equipment (WEEE) Notice Hazardous Substances NCC Statements Declaration of Conformity in Languages of the European Community Safety Guidelines This section contains notices that are intended to protect your personal safety and prevent damage to the equipment.
Regulatory Information FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference • This device must accept any interference received, including interference that may cause undesired operation.
Regulatory Information Caution Avertissement: 1 les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. 2 le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e.
Regulatory Information This radio transmitter (IC: 4141B-AP3917E/ Model: AP3917e) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Regulatory Information types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. 4.9G Antenna for Item 6 and Item 11 will be secondary primary permanent fixed operations use only.
Regulatory Information 3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment. 4 It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Environmental Compliance at Green@extremenetworks.com.
Regulatory Information Declaration of Conformity in Languages of the European Community The full text of the EU declaration of conformity is available at the following Internet address: http:// www.extremenetworks.com/ Note Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. English Hereby, Extreme Networks, Inc.
Regulatory Information German Hiermit erklärt Extreme Networks die Übereinstimmung des "WLAN Wireless Controller bzw. Access Points" mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Extreme Networks ΔΗΛΩΝΕΙ ΟΤΙ Radio LAN device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
