User's Manual

ManualsBrandsExtreme Networks ManualsElectronicsWireless 802.11 a/ac+b/g/n Access Point

Installing the ExtremeWiNG

AP7662i/AP7662

Access Point

Overview of the AP7662i/AP7662

The AP7662 is an IP67 rated Access Point with 802.11ac dual band 2:2 radios.

The AP7662 is easy to install, lightweight, and is available in an internal

(AP7662i) and external (AP7662) antenna model. Each model includes 802.11

radios, an IoT radio, and a GPS radio. The AP7662 model comes in two models:

AP7662i and AP7662. In this document, the functionality, feature, and the

procedure applies to both the models when AP7662i/AP7662 is used.

The AP7662i/AP7662 model has the following features:

• Radios: 2 radios (2.4GHz and 5GHz); 1 IoT/BLE/802.15.4 Radio (2.4 GHz)

•Console Port: RJ45

• One RJ45, 10/100/1000 Ethernet Port (GE1) with PoE

• One RJ45, 10/100/1000Mb Ethernet port (GE2)

• IP67 Connectors on all ports

•LEDs: 4 (see Figure 1)

•One Reset button

• Power: PoE 802.3af or 802.3at

• GPS Receiver (will be supported via a future firmware release)

• Antennas:

– AP7662i - Five internal antennas (four band locked antennas and one

BLE antenna)

– AP7662- Five external antennas (four single band antennas and one

BLE antenna)

• Temperature: -40 to 70*C ambient temperature

• Enclosure: Cast Aluminum base and Top

In Figure 1, the top image indicates AP7662i. Figure 2 shows the top and side

views of AP7662.

Figure 1 Top and Side Views of AP7662i

Figure 2 Top and Side Views of AP7662

Note: The AP7662i/AP7662 requires a minimum base firmware of

WiNG 5.9.1.

IoT/BLE Radio

Radio - 5 GHz

Radio - 2.4 GHz

Status

GE1 (PoE IN)

GE2

Console/Reset

Vent

IoT/BLE Radio

Radio - 5 GHz

Radio - 2.4 GHz

Status

GE1 (PoE IN)

GE2

Console/Reset

2.4 G - Antenna 1 and 2

LEDs on the Front of the AP

Amber LEDs indicate 5 GHz Wi-Fi Radio, Green LEDs indicate 2.4 GHz Wi-Fi

Radio, and Blue LED indicates the IoT Radio. The Status LED is ON only during

bootup.

For detailed installation information about the AP7662i/AP7662, see the

ExtremeWireless AP7662i/AP7662 Installation Guide.

Ta bl e 1 shows ways to power the AP7662i/AP7662.

Table 1 Powering the AP7662i/AP7662

Verifying the AP7662i/AP7662 Box Contents

Verify the contents of the box and ensure that the following items are

available:

Mounting and Connecting the AP

Use these instructions as guidelines for mounting and connecting the

AP7662i/AP7662 easily and safely.

The AP7662i/AP7662 mounting brackets are sold separately.

For more information about installing the optional bracket and the adapter,

see the ExtremeWireless AP7662i/AP7662 Installation Guide.

For installation videos of the AP, see www.extremenetworks.com/support/

Mounting the AP7662i/AP7662

Use these instructions as guidelines for mounting and connecting the

AP7662i/AP7662 easily and safely. The installation of the AP7662i/AP7662

should be performed by a professional installer to ensure proper operation

and compliance with local safety guidelines.

Attach the AP7662i/AP7662 to a surface that can support the AP and in an

environment it can withstand. It can be mounted to a wall, girder, ceiling, or

pole, and the surface material can be concrete, brick, wood, metal, or plastic.

Positioning the AP for Installation

Mount the AP so that the glands are on the side of the AP closest to the

ground, and not above the plastic cover. You must provide a 3-inch drip loop

on all cables.

Attach the Ground Wire

Use the M4 ground screw assembly, with the star washer, to attach the

ground wire’s ring terminal to the back of the AP. The wire should be as close

to the AP bottom as possible. Tighten the screw to a torque of 13.0-13.5 in-

lbs.

Mounting the AP7662i/AP7662 to a Wall

1 Using the mounting bracket as a guide, mark the location for the

mounting screws. The wall bracket provides eight attachment holes. Use

four (one in each corner). Place the bracket and mark the four hole

centers.

Vent

5G - Antenna 1

BLE/802.15.4 Antenna

5 G - Antenna 2

Power Source

Description

Power over

Ethernet

(PoE)

Power is provided through the RJ45 Ethernet port (GE1 port).

Table 2 Contents of the AP7662i/AP7662 Box

Quantity Item

1 AP7662i/AP7662 Quick Reference Guide

1 Cloud Quick Start Card

The following hardware is included:

1 M4 screw assembly with star washer

1 Ring terminal

Electrical Hazard: Only qualified personnel should perform

installation procedures.

Note: Do not remove the dust cap until you need to install the BLE/

IoT antennas.

Note: Attach the H bracket after attaching the ground wire onto the

AP. Tighten the torque, tighten the screws, and attach the LAN

cable.

Note: The “H” type Mounting Bracket (WS-MBO-H01) is sold as a

separate accessory (ordering part #30519).

2 Drill four holes into the wall as follows:

– for installing the AP on a masonry wall, use a 5/16” diameter bit.

– for other materials, use the appropriate drill for the screws being used.

3 For masonry installations, drill at least 1/8” (3mm) past the depth of the

screw, or bolt, being used, and place four anchor assemblies into the

holes.

4 Attach the AP to the “H” Bracket:

a Use four M4 screw assemblies to attach the AP to the “H” bracket on

the side that does not have the PEM stand-offs.

b Tighten the four screws to a torque of 13.0-13.5 in-lbs.

Figure 3 Attaching the “H” Bracket to the AP

5 Secure the anchors to the wall, then secure the bracket to the anchors.

6 If using #10 screws, tighten them to a torque of 25 in-lbs. If using ¼”

screws, tighten them to 45 in-lbs.

Figure 4 AP7662i and AP7662 Wall Mount “H” Bracket

Mounting the AP7662i/AP7662 to a Pole

1 Determine the diameter of the pole.

For other pole diameters, provide your own stainless steel cable clamp.

The band must be ½” (12.7mm) wide.

2 Attach the AP to the “Pole Mount” bracket using 4 M4 screws. Tighten the

four screws to a torque of 13.0-13.5 in-lbs.

Figure 5 Attaching a Pole Bracket to the AP

3 Attach the cable clamp to the pole bracket. Open the cable clamp by

turning a flat bladed screwdriver counterclockwise. Then, insert the non-

clamp end into the pole bracket through the holes.

4 Put the metal band around the pole and insert it into the clamp. Turn the

clamp screw clockwise, tightening the band around the pole.

Note: The Pole Mounting Bracket (WS-MBO-POLE01) is sold as a

separate accessory (ordering part #30520).

Pole Diameter Cable Clamp Size

<= 2.5” (63.5mm) Use small cable clamp.

5” - 7” (178mm) Use large cable clamp

Note: It is easier to install both clamps before attaching to the pole.

Figure 6 AP with Mounting Bracket—Vertical Pole

Mounting the AP7662i/AP7662 to a Wall/Pole

using the WS-MBO-ART01 2 Axis Extension

Arm

You can mount the to AP7662i/AP7662 to a wall or a pole using a 10”

extension arm (WS-MBO-ART01, ordering part #30514). For mounting and

installation instructions, refer to the ExtremeWireless AP7662i/AP7662

Installation Guide.

Installing External Antennas

1 Professionally install the external antennas intended for area coverage.

For information about antenna selection and installation, refer to the

External Antenna Site Preparation and Installation Guide.

2 Attach the external antenna cables to the Standard Polarity Type-N

connectors on the AP7662i/AP7662.

Connecting a Power Supply to the AP7662i/AP7662

If you need to power the AP7662i/AP7662, you can do so my using the GE1

port on the AP. The power LED on the front face of the AP illuminates when

the device is powered on. Refer to the ExtremeWireless AP7662i/AP7662

Installation Guide for more information.

LAN/Console Connections

The AP7662i/AP7662 has two LAN (Ethernet) ports and a Console port. Refer

to Figure 1 and Figure 2 for the location of these ports. During administration

and maintenance through the LAN or Console, the AP must still have a power

connection through either an Ethernet PoE cable or a DC power supply.

Professional Installation Instruction

Installation personnel

This product is designed for specific application and needs to be installed by a

qualified personnel who has RF and related rule knowledge. The general user

shall not attempt to install or change the setting.

Installation location

The product shall be installed at a location where the radiating antenna can be

kept 20 cm for AP7662i and 35 cm for AP7662 (FCC) and 20 cm for AP7662i

and 42 cm for AP7662 (ISED) from nearby person in normal operation

condition to meet regulatory RF exposure requirement.

External antenna

Use only the antennas which have been approved by the applicant. The non-

approved antenna(s) may produce unwanted spurious or excessive RF

transmitting power which may lead to the violation of FCC/ISED limit and is

prohibited.

Installation procedure

Please refer to user’s manual for the detail.

Instructions d'installation professionnelle

Installation

Ce produit est destine a un usage specifique et doit etre installe par un

personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant.

L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.

Emplacement d'installation

En usage normal, afin de respecter les exigences reglementaires concernant

l'exposition aux radiofrequences, ce produit doit etre installe de facon a

respecter une distance de 20cm pour AP7662i et 35 cm pour AP7662 (FCC)

et 20 cm pour AP7662i et 42 cm pour AP7662 (ISED) entre l'antenne

emettrice et les personnes.

Warning: Please carefully select the installation position and make sure that

the final output power does not exceed the limit set force in relevant rules. The

violation of the rule could lead to serious federal penalty.

Summary of content (2 pages)

PAGE 1
Installing the ExtremeWiNG AP7662i/AP7662 Access Point 9 Vent 10 5G - Antenna 1 Overview of the AP7662i/AP7662 12 5 G - Antenna 2 The AP7662 is an IP67 rated Access Point with 802.11ac dual band 2:2 radios. The AP7662 is easy to install, lightweight, and is available in an internal (AP7662i) and external (AP7662) antenna model. Each model includes 802.11 radios, an IoT radio, and a GPS radio. The AP7662 model comes in two models: AP7662i and AP7662.
PAGE 2
Antenn externe Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definis par ISED, ce qui est interdit. Procedure d'installation Consulter le manuel d'utilisation. Warning: Avertissement: Choisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur.