™ ExtremeMobility Access Points AP410i/e Installation Guide 9036459-00 RevAA Published November 2019
Copyright © 2019 Extreme Networks, Inc. All rights reserved. Legal Notice Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice.
Table of Contents Preface................................................................................................................................................................................................ 4 Conventions............................................................................................................................................................................. 4 Providing Feedback to Us.................................................................................
Preface This section discusses the conventions used in this guide, ways to provide feedback, additional help, and other Extreme Networks® publications. Conventions This section discusses the conventions used in this guide. Text Conventions The following tables list text conventions that are used throughout this guide. Table 1: Notice Icons Icon New! Notice Type Alerts you to... General Notice Helpful tips and notices for using the product. Note Important features or instructions.
Providing Feedback to Us Quality is our first concern at Extreme Networks, and we have made every effort to ensure the accuracy and completeness of this document. We are always striving to improve our documentation and help you work better, so we want to hear from you! We welcome all feedback but especially want to know about: • Content errors or confusing or conflicting information. • Ideas for improvements to our documentation so you can find the information you need faster.
1 Go to www.extremenetworks.com/support/service-notification-form. 2 Complete the form with your information (all fields are required). 3 Select the products for which you would like to receive notifications. Note You can modify your product selections or unsubscribe at any time. 4 Click Submit. Documentation and Training To find Extreme Networks product guides, visit our documentation pages at: Current Product Documentation www.extremenetworks.
• • • • • • • • • • ExtremeWireless External Antenna Site Preparation and Installation Guide ExtremeWireless External Antenna with Wave 2 Site Preparation and Installation Guide ExtremeWireless Getting Started Guide ExtremeWireless Integration Guide ExtremeWireless Maintenance Guide ExtremeWireless Open Source Declaration ExtremeWireless User Guide IdentiFi Wireless WS-AP3865e Installation Guide IdentiFi Wireless WS-AP3825i & WS-AP3825e Installation Guide IdentiFi Wireless WS-AP3805i & WS-AP3805e Installat
1 Product Overview AP410i/e Features AP410i/e Power Source LED Indicators The AP410i/e access points are indoor model 802.11ax access points. The “i” in AP410i indicates that the access point comes with internal antennas and the “e” indicates that it comes with external antenna connectors. The access points feature built-in dual-band radios, two band-locked radios, eight WiFi internal or external antennas, and one Bluetooth Low Energy (BLE) antenna.
Product Overview • AP410i: Eight WiFi internal antennas and one BLE internal antenna • AP410e: Six RP-SMA external antenna ports and one BLE RP-SMA antenna • • Temperature: • AP410i: 0°C to +50°C (32°F to +122°F) @ 6000 ft. • AP410e: -20°C to +55°C (-4°F to +131°F) @ 6000 ft. Enclosure: Plastic with metal base AP410i/e Power Source Power source Description Power over Ethernet (PoE) Power is provided through the 2.5 GE multi-rate Ethernet ports of AP410i/e, compliant to be powered with 802.
2 Install the Access Point AP410i/e Box Contents Access Point Installation Options and Accessories Information Install the Access Point on a Drywall or Wood Wall or to a Solid Flat Ceiling Install the Access Point on a Suspended or Drop Ceiling with a Flat T-bar Install the Access Point on a Junction Box or Gang Box Install the Access Point on a Beam The access point is installed on flat surfaces such as drywall or wood wall, solid flat ceiling, suspended or drop ceiling with T-bar, to beams, or to a juncti
Install the Access Point Quantity Item 2 2 Note All optional brackets and accessories are sold separately. Access Point Installation Options and Accessories Information The access point comes with the main mounting bracket (#37201; mounting bracket for 802.11ax indoor access points). There are various optional brackets, bracket adapters, and accessories that can be purchased separately.
Install the Access Point Table 7: Brackets and accessories usage for various installation options (continued) Mounting bracket or accessory Wall install Solid Ceiling Ceiling Juncti Beam flat install install on box install ceiling (T-bar) (protrude install install d T-bar) Ceiling tile protrusion T-bar widths Notes 37210 flat metal easyattach adapter; used with main mounting bracket Yes Yes No No No No No N/A Wall mount, ceiling mount, or install on any solid surface.
Install the Access Point Install the Access Point Using the Main Mounting Bracket The main mounting bracket is a stainless-steel bracket that ships with the access point. It is used during drywall or wood wall installation, or solid flat ceiling installation. Tip The best practice is to use the main mounting bracket for all wall installations. 1 Using the mounting bracket as a template, mark and drill two hole centers on the wall. Note The bracket feet must be pointing up.
Install the Access Point Callout Description 1 Main mounting bracket mounting holes 2 Main mounting bracket feet 2 Insert the Phillips pan head screws into the main mounting bracket holes and attach the bracket to the wall. Use screw-in anchors, if needed. 3 Connect the Ethernet cable RJ45 connector into the GE1 port. 4 Place the access point onto the bracket feet and slide it down to lock it in place.
Install the Access Point Callout Description 1 Security torx locking screw stop feature Note You cannot remove the access point from the main mounting bracket until the security torx locking screw is removed. Install the Access Point Using the WALL04 Bracket The optional WALL04 (#30516) bracket is used for wall installations and ships with two Phillips pan head screws and two screw-in anchors. You must purchase the bracket separately.
Install the Access Point 1 Keep the adapter to the center of the main mounting bracket, push and rotate it. Figure 3: Flat metal easy-attach adapter being attached to the main mounting bracket 2 Using the attachment holes on the easy-attach adapter, mark and drill two hole centers on a wall or a solid flat ceiling. 3 Attach the easy-attach adapter to the wall using two Phillips pan-head screws. Use screw-in anchors, if needed. 4 Connect the Ethernet cable RJ45 connector into the GE1 port.
Install the Access Point 5 Place the access point onto the bracket feet and slide it down to lock it in place. Note The bracket feet must be pointing up. Install the Access Point Directly on a Wall If you do not want to use the main mounting bracket that ships with the access point, you can install the access point directly on a wall using two phillips pan head screws. Tip The best practice is to use the main mounting bracket for wall installations. 1 Measure and drill two holes 104 mm (4.100 in.
Install the Access Point • • T-bar maximum base thickness must not exceed 0.055 in. (1.4 mm). Ceiling tile over the T-bar must be flat, all the way across. The main mounting bracket is used on a T-bar when the ceiling model is a suspended or drop ceiling and when there is a T-bar on the ceiling. 1 Remove the ceiling tiles. 2 Push and rotate the main mounting bracket on the T-bar in such a way that the center angled locking tabs of the main bracket gets attached to the T-bar.
Install the Access Point Install the Access Point on a Flat T-bar Using Main Mounting Bracket and KT-135628-01 Adapter Ensure that the T-bar meets the following conditions before installing the main mounting bracket with the KT-135628-01 adapter on a T-bar: • T-bar width can be either 9/16 in. (15 mm) or 15/16 in. (24 mm). • T-bar bottom must be flat all the way across. • T-bar must be structurally sound. • T-bar maximum base thickness must not exceed 0.055 in. (1.4 mm).
Install the Access Point Callout Description A KT-135628-01 adapter B KT-135628-01 T-bar holder C KT-135628-01 adapter locking pin 3 Slide the KT-135628-01 T-bar holder onto the T-bar and replace the tiles to hold the adapter onto the T-bar. 4 Hold and rock the access point back and forth to ensure that it is securely mounted. 5 Attach the RJ45 connector to the GE1 port.
Install the Access Point Callout Description 1 T-bar 2 Movable sliding part of the DCFLUSH bracket 3 Hook the stationary end of the bracket onto the T-bar. 4 Tilt the T-bar up slightly in such a way that you are holding the stationary and movable sides of the bracket. 5 Squeeze the bracket parts together until you hear the T-bar locking tab click into place. 6 Slide the bracket base into the rear groove the access point.
Install the Access Point 2 Open the movable sliding part of the DCMTR01 bracket to give the stationary end of the bracket and the slider T-bar more space. Figure 7: DCMTR01 bracket parts and T-bar Callout Description 1 T-bar 2 Movable sliding part of the DCMTR01 bracket 3 Stationary part of the DCMTR01 bracket 3 Hook the stationary end of the bracket onto the T-bar. 4 Tilt the T-bar up slightly in such a way that you are holding the stationary and movable parts of the bracket.
Install the Access Point 2 Remove the LAN cable from the coverplate. 3 Place the WALL04 bracket, with the locking tab pointing up, against the mounting holes on the box. Note The bracket must be square to the rest of the room walls, and the two holes that are being used must be on the opposite side of large center hole on the WALL04 bracket. If the WALL04 bracket holes do not align with the mounting holes on the junction or gang box, cut and enlarge the holes on the WALL04 bracket.
Install the Access Point 1 Attach the beam clip to the main mounting bracket. Slide the beam clip accessory into the rear hinges on either side of the main mounting bracket and slightly twist it until the clip locks into place. Figure 9: Beam clip accessory attached to the main mounting bracket 2 Place the access point onto the main mounting bracket feet and slide it down to lock it in place. 3 Place the beam clip accessory on a beam.
Install the Access Point 4 Tighten the beam clip accessory screw to secure the access point in place. Figure 10: Beam clip accessory attached to a beam 5 Connect the Ethernet cable RJ45 into the GE1 port.
3 Antenna Configuration for External Antenna Model Access Point Figure 11: AP410e external antennas Note The sensor and the BLE antennas come with dust caps on them. Do not remove the dust cap until you need to install the antennas.
Antenna Configuration for External Antenna Model Access Point Antenna socket radio mapping information • • • • Radio 1 (R1) - antennas 1 and 2 Radio 2 (R2) - antennas 1, 2, 3, and 4 Radio 3 (R3) - antennas 5 and 6 IoT radio - antenna 7 (IoT or BLE antenna) ExtremeMobility™ Access Points AP410i/e 27
4 Access Points Specifications Physical specifications Item Specification Housing Plastic LED Seven Radios Three 802.11ax radios Console port RJ45 Cloud enabled No Environmental specifications Item Specification Operating temperature AP410i: 0°C to +50°C (32°F to +122°F) AP410e: 20°C to +55°C (-4°F to +131°F) Operating altitude 6000 ft.
5 Regulatory Information Safety Guidelines MPE Statement for Mobile Devices Federal Communications Commission (FCC) Notice Industry Canada Notice Detachable Antenna Usage Australia Notice Brazil Anatel Statement Hazardous Substances Supplement to Product Instructions NCC Statement CE Information European Waste Electrical and Electronic Equipment (WEEE) Notice Declaration of Conformity in Languages of the European Community Safety Guidelines The following safety guidelines are intended to protect your perso
Regulatory Information a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Regulatory Information Warning IC Radiation Exposure Statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 39 cm between the radiator and your body. Warning Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé.
Regulatory Information Group Brand Model number Antenna type Antenna gain (dBi) 2.4 GHz 5 GHz BLE or thread 8 Extreme WS-AODQ04360N Omni 5.5 6 - 9 Extreme AI-DQ04360S Omni 5.5 6 - 10 Extreme ML-2452SEC6M4-036 / WS-AIDQ05120 Panel 6.92 7.23 - 11 Extreme WS-AIDE07025 Panel 7.5 6.5 - 12 Extreme ML-2452PNA7-01R Panel 1 7.8 10.7 7.8 13 Extreme WS-AIDE10055 Panel 2 10.5 7.
Regulatory Information Supplement to Product Instructions NCC Statement 功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號 或使用者均不得 擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條低功率射頻電機之 使用不得影響飛航安全及干擾合法通信；經發現有干擾現 象時，應立即停用，並改善至無干擾時方 得繼續使用。前項合法通信，指依電信法規 定作業之無線電通信。低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻 射性電機設備之干擾。 無線資訊傳輸設備避免影響附近雷達系統之操 作。 本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者 CE Information Warning CE co-location MPE Statement: This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment.
Regulatory Information IT LV LT LU MT NL PL PT RO SK SI ES SE UK Table 8: All operational modes Frequency AP410i AP410e 2.4 GHz 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ax (HEW20), 802.11ax (HEW40), 802.15.4 (Thread), Bluetooth (LE) 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), Bluetooth(BR/ EDR, LE) 5 GHz 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80), 802.11ac (VHT160), 802.
Regulatory Information 1 The symbol above indicates that separate collection of electrical and electronic equipment is required. 2 When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately.
Regulatory Information Danish Undertegnede Extreme Networks erklærer herved, at følgende udstyr Radio LAN device (AP410i/e) overholder de væsentlige krav og øvrige relevante krav i direktiv 2014/53/EU. For den fulde ordlyd af EUoverensstemmelseserklæringen bedes du kontakte Extreme Regulatory Compliance på compliancerequest@extremenetworks.com German Hiermit erklärt Extreme Networks die Übereinstimmung des "WLAN Wireless Controller bzw.
Regulatory Information Portuguese Extreme Networks declara que este Radio LAN device (AP410i/e) está conforme com os requisitos essenciais e outras disposições da Directiva 2014/53/EU. Para o texto integral da declaração de conformidade da UE, contacte a conformidade regulamentar extrema em compliancerequest@extremenetworks.
Index A access points specifications environmental specifications 28 physical specifications 28 power specifications 28 antenna configuration 26, 27 antennas external antennas 8 internal antennas 8 Australia notice 32 B beam install beam clip accessory 23 BRKT-000147A-01 accessory 23 box contents 10 C conventions notice icons 4 text 4 D DCFLUSH bracket install 20 DCMTR01 bracket install 21 detachable antenna usage 31 direct wall install 17 documentation feedback 5 location 6 Documentation, related 6 E e
Index product overview AP410e access point 8 AP410i access point 8 purchase order information bracket accessories beam clip accessory 7 flat metal easy-attach adapter 7 KT-135628-01 7 RJ45 flat cable accessory 7 mounting brackets main mounting bracket 7 WS-MBI-DCFLUSH bracket 7 WS-MBI-DCMTR01 bracket 7 WS-MBI-WALL04 bracket 7 power supply 7 R Regulatory Information 33 Regulatory Information, Hazardous Substances 32 S safety guidelines 29 security torx locking screw M3 security screw kit 14 security screw
