Installation Instructions

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesFast Ethernet and Gigabit Ethernet switches

Table Of Contents

Installation Job Aid for Ethernet Routing

Switch 3600 Series

NN47213-303

Issue 03.01

November 2017

Notices

Notice paragraphs alert you about issues that require your attention.

Following are descriptions of the types of notices used in this document.

Note:

Notes provide tips and useful information regarding the installation and operation of products.

Electrostatic alert:

ESD notices provide information about how to avoid discharge of static electricity and

subsequent damage to products.

Caution:

Caution notices provide information about how to avoid possible service disruption or damage to

products.

Warning:

Warning notices provide information about how to avoid personal injury when working with

products.

Voltage:

Danger—High Voltage notices provide information about how to avoid a situation or condition

that can cause serious personal injury or death from high voltage or electric shock.

Danger:

Danger notices provide information about how to avoid a situation or condition that can cause

serious personal injury or death.

2017, Extreme Networks, Inc.

Summary of content (9 pages)

PAGE 1
Installation Job Aid for Ethernet Routing Switch 3600 Series NN47213-303 Issue 03.01 November 2017 Notices Notice paragraphs alert you about issues that require your attention. Following are descriptions of the types of notices used in this document. Note: Notes provide tips and useful information regarding the installation and operation of products. Electrostatic alert: ESD notices provide information about how to avoid discharge of static electricity and subsequent damage to products.
PAGE 2
Safety messages Safety messages are an important part of the technical documentation. The messages alert you to hazards to personnel and equipment and provide guidance for the safe operation of your equipment. Failure to comply with the safety messages could result in equipment damage and personal injury. Following are the most common types of safety messages. Warning: Installation must be performed by qualified personnel only.
PAGE 3
AC power cord specifications The following section outlines the AC power cord specifications for various countries. Ensure that you use the correct cord for your location. Table 1: International power cord specifications Country and plug description Specifications Continental Europe 220 or 230 VAC • CEE7 standard VII male plug 50 Hz • Harmonized cord (HAR marking on the outside of the cord jacket to comply with the CENELEC Harmonized Document HD-21) Single phase U.S.
PAGE 4
Before you begin Ensure the area where you install and use the switch meets the following environmental requirements: • Ambient temperature between 32°F and 122°F (0°C and 50°C). • Relative humidity between 0% and 95% noncondensing. • No nearby heat sources such as hot air vents or direct sunlight. • No nearby sources of severe electromagnetic noise. • No excessive dust. • Adequate power source within six feet; one circuit required for each power supply. • At least 2 inches (5.
PAGE 5
Installing an ERS 3626GTS-PWR+ on a table or shelf You can install the switch model ERS 3626GTS-PWR+ on a flat surface such as a table or shelf. The surface must be able to support the combined weight of the switch and attached cables. An ERS 3626GTS-PWR+ weights 4.75kg (10.47lb). Important: Allow at least 5.1 cm (2 inches) on each side of the switch for proper ventilation and at least 12.7 cm (5 inches) at the back of the switch for power cord clearance.
PAGE 6
2. Set the switch on a table or shelf.
PAGE 7
Installing an ERS 3600 Series in an equipment rack Before you begin Tool requirements: • Phillips screwdriver to attach brackets to the switch and the switch to the rack. Rack requirements • Space of 2.8 inches (7.1 centimeters) for each switch in an E1A or 1EC standard 19 inch (48.2 centimeter) equipment rack and T1A 23 inch (58.5 cm) equipment rack. • Appropriate rack space to accommodate 1U switch height. • Rack bolted to floor and braced if necessary.
PAGE 8
Figure 2: Rack installation 4. Verify that the switch is securely fastened to the rack. Connecting AC power Before you begin • Ensure to check AC power specifications for the switch. • Ensure to check the AC power cord for international use. You must use a power cord that is approved for the receptacle type in your country. For more information, see AC power cord specifications on page 3. Procedure 1. Connect the AC power cord to the back of the switch, and then connect the cord to a power outlet.
PAGE 9
2. Check the front-panel LEDs as the device is powered on to be sure the PWR LED is lit. If not, check that the power cable is correctly plugged in. Connect the AC power cord to the back of the switch, and then connect the cord to a power outlet. Danger: Using power cords with a proper grounding path Use only power cords that have a grounding path. Without a proper ground, a person who touches the switch is in danger of receiving an electrical shock.