Enterasys® Wireless Outdoor Access Point Installation Guide WS-AP3660 P/N 9034605-02
Electrical Hazard: Only qualified personnel should perform installation procedures. Riesgo Electrico: Solamente personal calificado debe realizar procedimientos de instalacion. Elektrischer Gefahrenhinweis: Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden. Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice.
Hazardous Substances This product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment. European Waste Electrical and Electronic Equipment (WEEE) Notice In accordance with Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment (WEEE): 1.
ѻક䇈ᯢк䰘ӊ Supplement to Product Instructions 䚼ӊৡ⿄ (Parts) 䞥ሲ䚼ӊ (Metal Parts) ⬉䏃ഫ (Circuit Modules) ⬉㓚ঞ⬉㓚㒘ӊ (Cables & Cable Assemblies) ล᭭㘮ড়⠽䚼ӊ (Plastic and Polymeric parts) ⬉䏃ᓔ݇ (Circuit Breakers) ƻ˖ 䪙 3E ᳝↦᳝ᆇ⠽䋼ܗ㋴ (Hazardous Substance) ∲ 䬝 ݁Ӌ䫀 ⒈㘨㣃 +J &G &U 3%% h ƻ ƻ ƻ ƻ ƻ h ƻ ƻ ƻ ƻ ƻ h ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ƻ ⒈Ѡ㣃䝮 3%'( 㸼⼎䆹᳝↦᳝ᆇ⠽䋼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ䞣ഛ SJ/T 11363-2006 ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ Indicates that the concentration of the hazardous substance
Enterasys Networks, Inc. Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This document is an agreement (“Agreement”) between the end user (“You”) and Enterasys Networks, Inc.
4. EXPORT RESTRICTIONS. You understand that Enterasys and its Affiliates are subject to regulation by agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be relied upon by the exporting party.
10. ENFORCEMENT. You acknowledge and agree that any breach of Sections 2, 4, or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate, and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys’ rights under this Agreement in addition to any and all remedies available at law. 11. ASSIGNMENT.
Contents About This Guide Who Should Use This Guide .............................................................................................................................ix How to Use This Guide ......................................................................................................................................ix Related Documents ............................................................................................................................................
Industry Canada Compliance Statement ........................................................................................... B-3 Canada Conformance Standards ...................................................................................................... B-3 External Antennas ............................................................................................................................. B-4 European Community ............................................................................
About This Guide The guide describes how to mount and connect cables to the Enterasys Wireless Outdoor Access Point WS-AP3660. In addition, this guide provides information on the product certifications and national approvals for the WS-AP3660. Note: This guide does not provide information on configuration of the Enterasys Wireless Outdoor APs. For information on how to configure the Enterasys Wireless Outdoor APs, see the Enterasys Wireless Convergence Software User Guide.
Related Documents Related Documents The manuals listed below can be obtained from the World Wide Web in Adobe Acrobat Portable Document Format (PDF) at the following site: https://extranet.enterasys.com/downloads/ • Enterasys Wireless AP External Antenna Site Preparation and Installation Guide • Enterasys Wireless Convergence Software User Guide Typographical Conventions The following typographical conventions and icons are used in this document. blue type Indicates a hypertext link.
Getting Help Getting Help For additional support related to the WS-AP3660 or this document, contact Enterasys Networks using one of the following methods: World Wide Web www.enterasys.com/support/ Phone 1-800-872-8440 (toll-free in U.S. and Canada) or 1-978-684-1000 For the Enterasys Networks Support toll-free number in your country: www.enterasys.com/support/ Internet mail support@enterasys.com To expedite your message, please type [Wireless] in the subject line.
Getting Help xii About This Guide
1 Introduction This chapter provides general information about the Enterasys Wireless Outdoor Access Point WS-AP3660. For information about... Refer to page... WS-AP3660 Overview 1-1 WS-AP3660 LED Indicators 1-3 Antennas 1-4 External Antenna Connectors 1-4 Console Port 1-4 LAN Port 1-4 Reset Switch 1-5 Temperature Sensor 1-5 Heater Circuit 1-5 WS-AP3660 Overview The WS-AP3660 (see Figure 1-1 on page 1-2) enables you to extend your wireless LAN beyond the boundaries of indoor locations.
WS-AP3660 Overview Figure 1-1 WS-AP3660 Front View Note: The Enterasys Wireless Outdoor APs do not work without the Enterasys Wireless Controller. The following views (see Figure 1-2 and Figure 1-3) illustrate the connections to the WS-AP3660.
WS-AP3660 Overview Figure 1-3 1 2 3 4 WS-AP3660 Bottom View Radio 2 - Middle Antenna 12V DC Connector Status LEDs Radio 2 - Right Antenna 5 6 7 Reset Switch Console Port (RJ45) LAN Port (RJ45) Note: The WS-AP3660 provides six external antenna ports. The network administrator determines which antenna port will be used based on the external antenna selected. The WS-AP3660 can also be configured to select the antenna that provides the best possible data transmission (diversity).
WS-AP3660 Overview Table 1-1 WS-AP3660 LED Status Indicators LED Status Description 1 (Power) On Green Indicates the WS-AP3660 is working normally. Flashing Green Indicates: • running a self test • loading software program 2 (Ethernet Link) 3 (Wireless Link) 4 (Wireless Link) On Red Indicates a CPU or system failure. On Blue Indicates a valid 1Gbps Ethernet link. On Green Indicates a valid 100Mbps Ethernet link. On Red Indicates a valid 10Mbps Ethernet link.
WS-AP3660 Overview Note: The LAN port also supports power over Ethernet (PoE) based on the IEEE 802.3at standard. Refer to “Power Connections” on page 2-11, for information on supplying power to the WS-AP3660 network port from a network device, such as a switch, that provides Power over Ethernet (PoE). Reset Switch The WS-AP3660 provides a Reset Switch (see Figure 1-3 on page 1-3) to reset or restore factory default configurations.
WS-AP3660 Overview 1-6 Introduction
2 Installation This chapter provides installation instructions for the Enterasys Wireless Outdoor Access Point WS-AP3660 and the optional WS-AP3660 Power Supply. For information about... Refer to page... Package Contents 2-1 Separately Ordered Components 2-2 WS-AP3660 Installation Procedures 2-3 WS-AP3660 Power Supply Installation Procedures 2-11 Package Contents The WS-AP3660 package includes components necessary for installation. Unpacking the WS-AP3660 Unpack the WS-AP3660 as follows: 1.
Installation Separately Ordered Components Table 2-1 WS-AP3660 Supplied Components (Continued) Quantity 3. Item 1 Waterproof cable gland adapter assembly 1 Enterasys Wireless Outdoor AP Quick Reference Perform a visual inspection of the WS-AP3660 for any signs of physical damage. Contact Enterasys Networks if there are any signs of damage. Refer to “Getting Help” on page xi for details. Unpacking the WS-AP3660 Power Supply Unpack the WS-AP3660 Power Supply as follows: 1.
WS-AP3660 Installation Procedures Installation – WS-AIO-2S18018 — Indoor/Outdoor, 2.3 - 2.5GHz, 18dBi, 18 deg, Panel – WS-AO-DS05360 — Outdoor, 2.4 - 2.5/5.15 to 5.875GHz, 5dBI, Omni, Baton – WS-AO-5S10360 — Outdoor, 5GHz, 10dBi, Omni, Baton (FCC Domain only) – WS-AO-DT05120-1 — Outdoor, 2.3 - 2.7/4.9 - 6.1GHz, Triple-feed, 5dBI, 120 deg, Sector – WS-ANT21 — Outdoor, 2.3 - 2.4/5.1 - 5.8GHz, Omni, Baton – WS-AO-DX13025 — Outdoor, 2.4 - 2.5/5.1- 5.9 GHz, Six-feed, 12.5/11.
Installation WS-AP3660 Installation Procedures Attaching the Mounting Bracket To attach the mounting bracket to the WS-AP3660: 1. Determine the desired orientation (vertical or horizontal) of the mounting bracket (see Figure 2-1 on page 2-4). 2. Attach the mounting bracket and spacer to the WS-AP3660 using four M6 screws, four spring washers, and four flat washers (see Figure 2-2 on page 2-4).
WS-AP3660 Installation Procedures Installation Mounting the WS-AP3660 to a Wall To attach the WS-AP3660 to a wall: 1. Place the WS-AP3660 (with mounting bracket) firmly against the wall surface. 2. Secure the WS-AP3660 to the wall with four screws (see Figure 2-3 on page 2-5). Note: Screws for attaching the WS-AP3660 to a wall are not supplied with the product. The type and length of the screws will depend on the wall type and thickness.
Installation WS-AP3660 Installation Procedures Mounting the WS-AP3660 to a Pole To fit the mounting plate to a pole: 1. Determine the desired mounting orientation of the WS-AP3660 (see Figure 2-4).
WS-AP3660 Installation Procedures 2. Installation Feed the supplied stainless steel tie back straps through the openings in the mounting bracket (see Figure 2-5). Figure 2-5 Attaching Straps to the Mounting Bracket 1 Mounting bracket (horizontal position) 2 Stainless steel straps (X2) 3. Feed the free end of the strap around the pole. 4. Tighten the tensioning screw to adapt the strap to the diameter of the pole.
Installation WS-AP3660 Installation Procedures Figure 2-6 1 Installing Terminator Caps Terminator cap 2 Antenna connector LAN/Console Connections (with Cable Gland Adapter Assembly) The WS-AP3660 has both a LAN and a Console port. Refer to Figure 1-3 on page 1-3 for the location of these ports. Before connecting an RJ45 cable (not provided) to either port, a waterproof cable gland adapter assembly must be installed onto the cable (see Figure 2-7).
WS-AP3660 Installation Procedures Installation 2. Slide the claw and seal onto the RJ45 cable. 3. Screw the main body into the LAN or Console port of the WS-AP3660. 1 Main body 4. Plug the RJ45 cable into the LAN or Console port. 2 LAN or Console port Caution: Do not run the network cable through the cable conduit connector used for connecting the power cables. You must connect the network cable and power cables through separate connectors.
Installation 2-10 WS-AP3660 Installation Procedures 5. Slide the seal and claw into the main body. 6. Secure the seal nut onto the main body. 7. Tighten the assembly by hand.
WS-AP3660 Power Supply Installation Procedures Installation Ground Connection 1. The ground connection for the WS-AP3660 is located on the rear of the device. Attach a ground to earth cable to one of two grounding terminals using one ground screw (see Figure 2-8).
Installation WS-AP3660 Power Supply Installation Procedures Attaching the Mounting Bracket To attach the mounting bracket to the WS-AP3660 Power Supply: 1. Determine the desired orientation (vertical or horizontal) of the mounting bracket (see Figure 2-9). In the horizontal position, two power supplies can be attached to one bracket. 2. Attach the mounting bracket and spacer to the power supply using four M5 screws, four spring washers, and four flat washers (see Figure 2-10).
WS-AP3660 Power Supply Installation Procedures Installation Mounting the Power Supply to a Wall To attach the power supply to a wall: 1. Place the power supply firmly against the wall surface. 2. Position the mounting bracket so the mounting holes are aligned with wall studs. 3. Secure the power supply to the wall with four screws (see Figure 2-11). Note: Screws for attaching the power supply to a wall are not supplied with the product.
Installation WS-AP3660 Power Supply Installation Procedures Figure 2-12 Power Supply Pole Mount Options 1 2 Vertical bracket on vertical pole Horizontal bracket on vertical pole 3 Horizontal bracket on horizontal pole 2. Feed the supplied stainless steel tie back straps through the openings in the mounting bracket (see Figure 2-5 on page 2-7). 3. Feed the free end of the strap around the pole. 4. Tighten the tensioning screw to adapt the strap to the diameter of the pole.
WS-AP3660 Power Supply Installation Procedures Figure 2-13 1 Installation WS-AP3660 Power Supply Connections AC Power Receptacle 2 DC Connector Note: The DC to DC cable forms a drip loop that allows water to safely drip away from the connections to both the WS-AP3660 and Power Supply (see Figure 2-14 on page 2-15). 5. Screw on and hand tighten the knurled knob securely.
Installation WS-AP3660 Power Supply Installation Procedures Connecting the Power Supply to AC Power The WS-AP3660 Power Supply provides a power receptacle for connecting the unit to an external AC power source. The power supply is shipped with a waterproof AC connector assembly (see Figure 2-15), but a power cord is not provided. Before connecting the power supply to AC power, the AC connector assembly must be installed onto the power cord.
WS-AP3660 Power Supply Installation Procedures Installation 3. Insert the sheathed cable through the sealing nut, clamp ring, seal, and body. 4. Insert the cable conductors into the housing assembly using the pin out diagram shown in Figure 2-16. Figure 2-16 Power Cable Pin Out Diagram 1 2 Pin 1 - Hot Pin 2 - Not used 3 4 Pin 3 - Neutral Pin 4 - Ground 5. Secure the wires by tightening the single lock nut with a 1.5 mm (Hex) driver.
Installation WS-AP3660 Power Supply Installation Procedures 6. Screw the body into the housing assembly and tighten. 7. Screw the sealing nut into the body and tighten. 8. Insert the assembled AC connector into the AC power receptacle on the power supply (see Figure 2-13 on page 2-15). 9. Screw on and hand tighten the knurled knob securely. 10. Insert the plug into the AC power source.
A Specifications This appendix lists the specifications for the Enterasys Wireless Outdoor Access Point WS-AP3660 and the WS-AP3660 Power Supply. Table A-1 Specifications for the WS-AP3660 Item Specification Enclosure material Metal enclosure IP67 rated Power source 802.3at compliant PoE PD 12V DC input Power consumption < 40W (Max.) Outside dimensions (max) 9.8 x 10.23 inches 250 x 260 mm Antenna 6x RP-N Jack antenna connectors; 2.
Table A-2 Specifications for the WS-AP3660 Power Supply Item Specification Enclosure material Metal enclosure IP67 rated AC Input 90 to 264V DC output 12V Outside dimensions (max) 8.5 x 4.
B Regulatory Information Warning: Warnings identify essential information. Ignoring a warning can lead to problems with the application. This appendix provides regulatory information for the WS-AP3660. Notes: Specific AP models are only identified in this appendix where it is necessary to do so. Warning: Changes or modifications made to the WS-AP3660s which are not expressly approved by Enterasys could void the user's authority to operate the equipment.
WS-AP3660 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential and business environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with instructions, may cause harmful interference.
WS-AP3660 operated in the 2.4 GHz and 5 GHz frequency ranges. This device must not be co-located or operated in conjunction with any other antenna or transmitter. The radiated output power of the WS-AP3660 is below the FCC radio frequency exposure limits as specified in “Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields” (OET Bulletin 65, Supplement C).
WS-AP3660 Canada Conformance Standards This equipment meets the following conformance standards: Safety • C22.2 No.60950-1-03 EMC • ICES-003, Class B Radio transceiver • RSS-210 (2.4 GHz and 5GHz) Other • IEEE 802.11a (5 GHz) • IEEE 802.11b/g (2.4 GHz) • IEEE 802.11n (WS-AP3660) • IEEE 802.3af (PoE) External Antennas The external antennas used with the WS-AP3660 must be approved and certified before use.
WS-AP3660 Declaration of Conformity in Languages of the European Community English Hereby, Enterasys, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Valmistaja Enterasys vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
WS-AP3660 Slovenian Šiuo Enterasys deklaruoja, kad šis Radio LAN device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Latvian Ar šo Enterasys deklarē, ka Radio LAN device atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem Lithuanian Enterasys deklaruoja, kad Radio LAN device atitinka 1999/5/EC Direktyvos esminius reikalavimus ir kitas nuostatas".
WS-AP3660 External Antennas The external antennas used with the WS-AP3660 must be approved and certified before use. However, in order to comply with the local laws and regulations, an approval may be required by the local regulatory authorities. For a list of approved external antennas, see “WS-AP3660 Approved External Antennas” on page B-10.
WS-AP3660 European Spectrum Usage Rules The AP configured with approved internal or external antennas can be used for indoor and outdoor transmissions throughout the European community as displayed in Table B-1. Some restrictions apply in Belgium, France, Greece, and Italy. Table B-1 European Spectrum Usage Rules Country 5.15-5.25 (GHz) Channels: 36,40,44,48 5.25-5.35 (GHz) Channels: 52,56,60,64 5.47-5.725 (GHz) Channels: 100,104,108,112,116, 132,136,140 2.4-2.
Certifications of Other Countries Table B-1 European Spectrum Usage Rules (continued) Country 5.15-5.25 (GHz) Channels: 36,40,44,48 5.25-5.35 (GHz) Channels: 52,56,60,64 5.47-5.725 (GHz) Channels: 100,104,108,112,116, 132,136,140 2.4-2.
Certifications of Other Countries WS-AP3660 Approved External Antennas The WS-AP3660 external antenna APs can be used with certified external antennas. However, in order to comply with the local laws and regulations, an approval may be required by the local regulatory authorities. The optional antennas listed in Table B-2 have been tested and approved for use with the external antenna models.
