Installation Guide

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesNext-Generation Programmable Leaf Switch

Table Of Contents

9037033-00 Rev AA

July 2021

Brocade SLX 9240 Switch

Hardware Installation Guide

HARDWARE INSTALLATION GUIDE

Summary of content (90 pages)

PAGE 1
HARDWARE INSTALLATION GUIDE Brocade SLX 9240 Switch Hardware Installation Guide 9037033-00 Rev AA July 2021
PAGE 2
© 2021, Brocade Communications Systems, Inc. All Rights Reserved. Brocade, the B-wing symbol, and MyBrocade are registered trademarks of Brocade Communications Systems, Inc., in the United States and in other countries. Other brands, product names, or service names mentioned of Brocade Communications Systems, Inc. are listed at www.brocade.com/en/legal/ brocade-Legal-intellectual-property/brocade-legal-trademarks.html. Other marks may belong to third parties.
PAGE 3
Contents Preface Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii Notes, cautions, and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii Text formatting conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
Installing the Universal Two-Post Rack Kit (XBR-R000294). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
Time and items required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Replacing a fan assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Inserting a new fan assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
vi Brocade SLX 9240 Switch Hardware Installation Guide 53-1004985-03
PAGE 7
Preface • • • • Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Brocade resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
Brocade resources Command syntax conventions Bold and italic text identify command syntax components. Delimiters and operators define groupings of parameters and their logical relationships. Convention Description bold text Identifies command names, keywords, and command options. italic text Identifies a variable. value In Fibre Channel products, a fixed value provided as input to a command option is printed in plain text, for example, --show WWN.
PAGE 9
Contacting Brocade Technical Support Provide the publication title, part number, and as much detail as possible, including the topic heading and page number if applicable, as well as your suggestions for improvement. Contacting Brocade Technical Support As a Brocade customer, you can contact Brocade Technical Support 24x7 online or by telephone. Brocade OEM customers contact their OEM/solution provider.
PAGE 10
Contacting Brocade Technical Support x Brocade SLX 9240 Switch Hardware Installation Guide 53-1004985-03
PAGE 11
About This Document • Supported hardware and software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Supported hardware and software The following tables list the power supplies, fan assemblies, and rack mount kits supported on the Brocade SLX 9240 switch running SLX-OS 17s.1.01.
PAGE 12
Supported hardware and software 2 Brocade SLX 9240 Switch Hardware Installation Guide 53-1004985-03
PAGE 13
Device Overview • • • • Hardware features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Port-side view of the Brocade SLX 9240 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Nonport-side view of the Brocade SLX 9240 switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 14
Nonport-side view of the Brocade SLX 9240 switch 1 10/100/1000Base-T RJ-45 management port 4 Mini-USB console port 2 QSFP28 ports 1- 32 5 System LEDs 3 USB port (for flash drive) Nonport-side view of the Brocade SLX 9240 switch Figure 2 shows the rear view of the Brocade SLX 9240 switch.
PAGE 15
Preparing for Installation • • • Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Facility requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Quick installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 16
Safety precautions CAUTION To protect the serial port from damage, keep the cover on the port when not in use. CAUTION Never leave tools inside the chassis. CAUTION If you do not install a module or a power supply in a slot, you must keep the slot filler panel in place. If you run the chassis with an uncovered slot, the system will overheat. CAUTION Use the screws specified in the procedure. Using longer screws can damage the device.
PAGE 17
Safety precautions DANGER Disconnect the power cord from all power sources to completely remove power from the device. DANGER This device might have more than one power cord. To reduce the risk of electric shock, disconnect all power cords before servicing. CAUTION To avoid high voltage shock, do not open the device while the power is on. CAUTION Use a separate branch circuit for each power cord, which provides redundancy in case one of the circuits fails.
PAGE 18
Facility requirements DANGER Laser radiation. Do not view directly with optical instruments. Class 1M laser products. DANGER Use only optical transceivers that are qualified by Brocade Communications Systems, Inc. and comply with the FDA Class 1 radiation performance requirements defined in 21 CFR Subchapter I, and with IEC 825 and EN60825. Optical products that do not comply with these standards might emit light that is hazardous to the eyes.
PAGE 19
Facility requirements • Allow for twisted-pair cables to be routed away from power lines, fluorescent lighting fixtures, and other sources of electrical interference, such as radios and transmitters. • Allow for the unit to be connected to a separate grounded power outlet that provides 100 to 240 VAC, 50 to 60 Hz, is within 2 m (6.6 ft) of each device, and is powered from an independent circuit breaker. As with any equipment, a filter or surge suppressor is recommended.
PAGE 20
Quick installation checklist Quick installation checklist Follow the steps listed in Table 2 to install your device. Details for each of these steps are provided on the pages indicated. TABLE 2 Installation tasks Task number Task Where to find more information 1 Ensure that the physical environment that will host the device has the proper cabling and ventilation.
PAGE 21
Mounting the Device • • • • • • • Mounting options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Precautions specific to mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Installing the device in a rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 22
Installing the device in a rack CAUTION Do not install the device in an environment where the operating ambient temperature might exceed 50°C (122°F). Installing the device in a rack CAUTION Make sure the rack housing the device is adequately secured to prevent it from becoming unstable or falling over. NOTE You need a #2 Phillips screwdriver for installation.
PAGE 23
Four-post rack mount installation (XBR-R000297) Parts list The following parts are provided with the four-post flush-mount rack kit (XBR-R000297). FIGURE 3 Items in the four-post flush-mount rack kit 1 Front brackets (2) 3 Screw, 10-32 x 5/8-in., panhead Phillips (12) 2 Rear brackets (2) 4 Retainer nut, 10-32 (12) Ensure that the items listed and illustrated in Figure 3 are included in the kit. CAUTION Use the screws specified in the procedure. Using longer screws can damage the device.
PAGE 24
Four-post rack mount installation (XBR-R000297) Attaching the front brackets Complete the following steps to attach the front brackets to the device. 1. Position the right front bracket with the flat side against the right side of the device over the six pre-installed keyhole fasteners, as shown in Figure 4. 2. Slide the bracket toward the front of the device until the bracket latch clicks into its secure position. 3.
PAGE 25
Four-post rack mount installation (XBR-R000297) FIGURE 5 1 Positioning the device in the rack Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 Attaching the rear brackets to the rack posts Complete the following steps to attach the rear brackets to the rack posts. 1. Slide the right rear bracket into the right front bracket and the left rear bracket into the left front bracket. 2. Adjust the rear brackets to the rack depth. 3.
PAGE 26
Installing the Universal Two-Post Rack Kit (XBR-R000294) FIGURE 6 1 Attaching the rear brackets to the rack posts Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 Installing the Universal Two-Post Rack Kit (XBR-R000294) Use the following instructions to install the Brocade SLX 9240 switch in a two-post telecommunications (Telco) rack using the Universal Two-Post Rack Kit (XBR-R000294).
PAGE 27
Installing the Universal Two-Post Rack Kit (XBR-R000294) Parts list The following parts are provided with the Universal Two-Post Rack Kit (XBR-R000294). FIGURE 7 Rack kit parts 1 Front brackets (2) 5 Screw, 8-32 x 5/16-in., flathead Phillips (16) 2 Rear brackets, 5-6 inch post (2) 6 Screw, 6-32 x 1/4-in., panhead Phillips (8) 3 Rear brackets, 3-5 inch post (2) 7 Screw, 10-32 x 5/8-in., panhead Phillips (8) 4 Screw, 8-32 x 5/16-in.
PAGE 28
Installing the Universal Two-Post Rack Kit (XBR-R000294) 4. “Attaching the rear brackets to the switch” on page 20 Attaching the front brackets Complete the following steps to attach the front brackets to the switch. 1. Use a #2 Phillips screwdriver to remove the 12 pre-installed keyhole fasteners from both sides of the switch. 2. Position the right front bracket with the flat side against the right side of the switch as shown in Figure 8. 3. Insert four 8-32 x 5/16-in.
PAGE 29
Installing the Universal Two-Post Rack Kit (XBR-R000294) FIGURE 9 1 Attaching front brackets to a rack Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 Attaching the rear brackets to the rack posts Complete the following steps to attach the rear brackets to the rack. 1. Select the proper length bracket for your post width. If your posts are three to five inches wide, use the brackets marked 3-5 INCH. If your posts are five to six inches wide, use the brackets marked 5-6 INCH. 2.
PAGE 30
Installing the Universal Two-Post Rack Kit (XBR-R000294) FIGURE 10 Attaching the rear brackets to a rack 1 Retainer nuts, 10-32 2 Rear brackets 3 Screws, 10-32 x 5/8-in., panhead Phillips Attaching the rear brackets to the switch Complete the following steps to attach the rear brackets to the switch. 20 1. Align the right rear bracket to the right rear of the switch and using four 8-32 x 5/16-in. panhead screws, attach the bracket to the switch as shown in Figure 11.
PAGE 31
Installing the Universal Two-Post Rack Kit (XBR-R000294) FIGURE 11 Attaching the rear brackets to the switch 1 Screws, 8-32 x 5/16-in., panhead Phillips Mid-mounting the switch The mid-mounting is similar to the flush-front mounting except that the brackets are positioned differently on the device. CAUTION The device must be turned off and disconnected from the fabric during this procedure. Complete the following tasks to install the device in a two-post rack. 1.
PAGE 32
Installing the Universal Two-Post Rack Kit (XBR-R000294) FIGURE 12 Attaching the front brackets 1 The Brocade device 2 Front brackets 3 Screws, 8-32 x 5/16-in., flathead Phillips Attaching the front brackets to the rack posts Complete the following steps to install the switch in the rack. 22 1. Position the switch in the rack (Figure 13), providing temporary support under the switch until the rack kit is fully secured to the rack. 2.
PAGE 33
Installing the Universal Two-Post Rack Kit (XBR-R000294) FIGURE 13 Attaching front brackets to a rack 1 Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 Attaching the rear brackets to the rack posts Complete the following steps to attach the rear brackets to the rack. 1. Select the proper length bracket for your post width. If your posts are three to five inches wide, use the brackets marked 3-5 INCH. If your posts are five to six inches wide, use the brackets marked 5-6 INCH. 2.
PAGE 34
Installing the Universal Two-Post Rack Kit (XBR-R000294) FIGURE 14 Attaching the rear brackets to a rack 1 Retainer nuts, 10-32 2 Rear brackets 3 Screws, 10-32 x 5/8-in., panhead Phillips Attaching the rear brackets to the switch Complete the following steps to attach the rear brackets to the switch. 24 1. Align the right rear bracket to the right rear of the switch and using four 8-32 x 5/16-in. panhead screws, attach the bracket to the switch as shown in Figure 15.
PAGE 35
Installing the Universal Four-Post Rack Kit (XBR-R000296) FIGURE 15 Attaching the rear brackets to the switch 1 Screws, 8-32 x 5/16-in., panhead Phillips Installing the Universal Four-Post Rack Kit (XBR-R000296) Use the following instructions to install the Brocade 9240 switch in EIA racks that are between 31.77 to 81.28 cm deep (12.51 to 32.0 in.) using the Universal Four-Post Rack Kit (XBR-R000296).
PAGE 36
Installing the Universal Four-Post Rack Kit (XBR-R000296) • 1/4-inch slotted-blade screwdriver Parts list The following parts are provided with the Universal Four-Post Rack Kit (XBR-R000296). FIGURE 16 Rack kit parts 1 Front brackets (2) 6 Screw, 8-32 x 5/16-in., panhead Phillips (8) 2 Extension brackets, medium (2) 7 Screw, 8-32 x 5/16-in., flathead Phillips (16) 3 Rear brackets, short (2) 8 Screw, 6-32 x 1/4-in., panhead Phillips (8) 4 Rear brackets, long (2) 9 Screw, 10-32 x 5/8-in.
PAGE 37
Installing the Universal Four-Post Rack Kit (XBR-R000296) Flush-front mounting CAUTION The device must be turned off and disconnected from the fabric during this procedure. Complete the following tasks to install the device in a four-post rack. 1. “Attaching the front brackets” on page 27 2. “Attaching the extension brackets to the device” on page 28 3. “Installing the device in the rack” on page 28 4. “Attaching the rear brackets to the extensions” on page 29 5.
PAGE 38
Installing the Universal Four-Post Rack Kit (XBR-R000296) Attaching the extension brackets to the device Complete the following steps to attach the extension brackets to the device. There are medium and long extension brackets that you can use for this step. Choose the correct extension bracket for the depth of your rack. 1. Select the proper length extension bracket for your rack depth. 2. Position the right extension bracket along the side of the device as shown in Figure 18. 3.
PAGE 39
Installing the Universal Four-Post Rack Kit (XBR-R000296) FIGURE 19 Positioning the device in the rack 1 Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 Attaching the rear brackets to the extensions Complete the following steps to attach the rear brackets to the extensions. There are short and long rear brackets that you can use for this step. Choose the correct bracket for the depth of your rack. 1. Select the proper length rear bracket for your rack depth. 2.
PAGE 40
Installing the Universal Four-Post Rack Kit (XBR-R000296) Attaching the rear brackets to the rack posts Complete the following steps to attach the rear brackets to the rack posts. 1. Attach the right rear bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts, as shown in Figure 21. Use the upper and lower holes in the bracket. 2. Attach the left rear bracket to the left rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts.
PAGE 41
Installing the Universal Four-Post Rack Kit (XBR-R000296) 5. “Attaching the rear brackets to the front rack posts” on page 34 Attaching the front brackets to the rear of the device NOTE In this installation, the brackets are named as listed in the parts list even though the installation of the brackets is reversed from the flush-front installation. Complete the following steps to attach the front brackets to the rear of the device. 1.
PAGE 42
Installing the Universal Four-Post Rack Kit (XBR-R000296) 5. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg). FIGURE 23 Attaching the bracket extensions to the device 1 Extension brackets 2 Screws, 8-32 x 5/16-in., flathead Phillips Installing the device in the rack Complete the following steps to install the device in the rack. 32 1.
PAGE 43
Installing the Universal Four-Post Rack Kit (XBR-R000296) FIGURE 24 Positioning the device in the rack 1 Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 Attaching the rear brackets to the extensions at the front of the device Complete the following steps to attach the rear brackets to the extensions. There are short and long front brackets that you can use for this step. Choose the correct bracket for the depth of your rack. 1.
PAGE 44
Installing the Universal Four-Post Rack Kit (XBR-R000296) FIGURE 25 Attaching the rear brackets to the extensions at the front of the device 1 Rear brackets, short 2 Screws, 6-32 x 1/4-in., panhead Phillips FIGURE 26 Attaching the short or long rear brackets to the extensions 1 Rear bracket, short or long 2 Screws, 6-32 x 1/4-in., panhead Phillips Attaching the rear brackets to the front rack posts Complete the following steps to attach the rear brackets to the front rack posts. 34 1.
PAGE 45
Installing the Universal Four-Post Rack Kit (XBR-R000296) FIGURE 27 Attaching the rear brackets to the front rack posts 1 Screws, 10-32 x 5/8-in.
PAGE 46
Installing the Universal Four-Post Rack Kit (XBR-R000296) 36 Brocade SLX 9240 Switch Hardware Installation Guide 53-1004985-03
PAGE 47
Initial Setup and Verification • • • Providing power to the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Establishing a first-time serial connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Establishing an Ethernet connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 48
Establishing an Ethernet connection For port pinout information for the mini-USB serial console port, refer to “Serial port specifications (pinout - mini-USB)” on page 64. 2. Disable any serial communication programs running on the workstation such as synchronization programs. 3.
PAGE 49
Installing Transceivers and Cables • • • • • • Precautions specific to transceivers and cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Cleaning the fiber-optic connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Managing cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 50
Managing cables Managing cables The minimum bend radius for a 50 micron cable is 2 inches under full tensile load and 1.2 inches with no tensile load. Cables can be organized and managed in a variety of ways, for example, using cable channels on the sides of the rack or patch panels to minimize cable management. Follow these recommendations: NOTE You should not use tie wraps with optical cables because they are easily overtightened and can damage the optic fibers.
PAGE 51
Replacing a fiber-optic transceiver DANGER Laser radiation. Do not view directly with optical instruments. Class 1M laser products. Use the following steps to install a transceiver. 1. Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack) to act as ground. 2. Remove the new transceiver from the protective packaging. 3. Remove any protector plugs from the transceivers and the ports. 4.
PAGE 52
Connecting network devices DANGER For safety reasons, the ESD wrist strap should contain a series 1 megohm resistor. To remove a fiber-optic transceiver from a QSFP28 slot, do the following. 1. Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack). 2. Disconnect the fiber cable connector from the port connector. 3. Unlock the fiber-optic transceiver by pulling the pull tab forward, away from the front of the slot.
PAGE 53
Connecting network devices To connect the device to another network device using a fiber port, you must complete the following tasks: • • Install a fiber-optic transceiver (QSFP+/QSFP28). Refer to “Installing a fiber-optic transceiver” on page 40. Cable the fiber-optic transceiver Cabling a fiber-optic transceiver Use the following steps to cable a fiber-optic transceiver. 1. Remove the protective covering from the fiber-optic port connectors and store the covering for future use. 2.
PAGE 54
Connecting network devices 44 Brocade SLX 9240 Switch Hardware Installation Guide 53-1004985-03
PAGE 55
Monitoring the Device • • • • • LED activity interpretation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Brocade SLX 9240 switch port-side LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Brocade SLX 9240 switch nonport-side LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 56
Brocade SLX 9240 switch nonport-side LEDs FIGURE 29 Brocade SLX 9240 switch port-side LEDs 1 Management port link LED 5 QSFP28 port 4x25/10 GbE mode lane 3 link/activity LED 2 Management port speed LED 6 QSFP28 port 4x25/10 GbE mode lane 4 link/activity LED 3 7 QSFP28 port 100/40 GbE and 2x50 GbE mode link/activity LED or 4x25/10 GbE mode lane 1 link/activity LED Power LED 4 QSFP28 port 4x25/10 GbE mode lane 2 link/activity LED 8 Status LED Brocade SLX 9240 switch nonport-side LEDs The Broca
PAGE 57
LED patterns LED patterns The following tables describe the Brocade SLX 9240 switch LED patterns. TABLE 3 Power LED LED state Status of hardware Recommended action Off (no light) System is off or there is no power. Verify the system is on and has completed booting. Steady green System is on. No action required. LED state Status of hardware Recommended action Off (no light) System is off or there is no power. No action required. Steady green Normal operation. No action required.
PAGE 58
Diagnostic tests and monitoring TABLE 9 Power supply input LED LED state Status of hardware Recommended action Off (no light) Power supply is not receiving external power. Verify that the Power supply power cord is connected to a functioning power source. Steady green Power supply is receiving external power. No action required. Blinking green (with power cord connected) Power supply has a fault. Replace the power supply.
PAGE 59
Power Supplies • • • • • • • • Power supply overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Precautions specific to power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Identifying the airflow direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 60
Precautions specific to power supplies FIGURE 31 AC power supply 1 Release lever 2 Power supply handle 2 Release lever FIGURE 32 DC power supply 1 Power supply handle Precautions specific to power supplies DANGER Make sure that the power source circuits are properly grounded, then use the power cord supplied with the device to connect it to the power source.
PAGE 61
Identifying the airflow direction DANGER If the installation requires a different power cord than the one supplied with the device, make sure you use a power cord displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark is your assurance that the power cord can be used safely with the device. CAUTION Disassembling any part of the power supply and fan assembly voids the warranty and regulatory certifications.
PAGE 62
Time and items required Time and items required Installing or removing and replacing a power supply should require less than five minutes to complete. A new power supply (with the same airflow direction as the power supply being replaced) is required to replace a power supply. Replacing a power supply When installing or replacing a power supply unit, keep in mind the following: • Power supplies can be swapped in or out while the device is running.
PAGE 63
Inserting a new DC power supply 3. Before opening the package that contains the power supply, touch the bag to the switch casing to discharge any potential static electricity. Brocade recommends using an ESD wrist strap during installation. 4. Remove the power supply from the anti-static shielded bag. 5.
PAGE 64
Inserting a new DC power supply 2. Prepare the power and safety grounding wires using the appropriate size wire. Crimp on ring lugs and heat shrink tube for all three wires. Due to the limited space for the safety ground wire, Brocade recommends using a 90-degree angled lug such as: • • TE Connectivity Solistrand “16-14HD 90 Ring 8,” part number 184269-1 for 14 AWG wire. PIDG 12-10 Ring #8, 90-DEG, part number 1958340-1 for 12 or 10 AWG wire. 3.
PAGE 65
Grounding the Brocade SLX 9240 switch Grounding the Brocade SLX 9240 switch The rear panel of the Brocade SLX 9240 switch includes a dual-screw grounding terminal for NEBS-compliant grounding. The surface area around this terminal is not painted to provide a good electrical connection. Before connecting power to the device, the grounding terminal must be connected to ground to meet NEBS compliance.
PAGE 66
Grounding the Brocade SLX 9240 switch NOTE The terminal for the connection of a grounding conductor is not to be used with an aluminum conductor. NOTE To ensure adequate bonding when attaching the ground lug, a minimum of 20 in-lb (2.76 Nm) of torque is required to be applied to the mounting hardware used to attach the ground lug.
PAGE 67
Fan Assemblies • • • • • • Fan assembly overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Precautions specific to fan assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Identifying the airflow direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 68
Precautions specific to fan assemblies Precautions specific to fan assemblies DANGER Be careful not to accidently insert your fingers into the fan tray while removing it from the chassis. The fan may still be spinning at a high speed. CAUTION Disassembling any part of the power supply and fan assembly voids the warranty and regulatory certifications. There are no user-serviceable parts inside the power supply and fan assembly.
PAGE 69
Time and items required Time and items required Installing or removing and replacing a fan assembly should require less than five minutes to complete. The following items are required to replace a fan assembly: • • New fan assembly (must have the same airflow direction as the fan assembly being replaced) #1 Phillips screwdriver Replacing a fan assembly When installing or replacing a fan assembly unit, keep in mind the following: • Fan assemblies can be swapped in or out while the device is running.
PAGE 70
Inserting a new fan assembly a. Using a Phillips screwdriver, unscrew the captive screw on the filler panel. b. Remove the filler panel. 3. Before opening the package that contains the new fan assembly, touch the bag to the switch casing to discharge any potential static electricity. It is recommended that you wear an ESD wrist strap during installation. 4. Remove the fan assembly from the anti-static shielded bag. NOTE Do not force the installation.
PAGE 71
Brocade SLX 9240 Switch Technical Specifications • • • • • • • • • • • • • • • • System specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 LEDs . . . . . . . . . . . . . . . . . . . . .
PAGE 72
LEDs LEDs System component Description Device status and management Two LED types indicate device status: Power (power supply) Status (diagnostics) Ports LEDs indicate port status (link/activity) Other System component Description Serial cable 1 (Mini-USB to RJ-45) RJ-45 to DB9 adapter 1 (RJ-45 port to female DB9 connector) AC power cord IEC 320-C14 Weight and physical dimensions Height Width Depth Fully loaded weight (no transceivers) 4.37 cm 44.0 cm 44.47 cm 9.07 kg 1.72 inches 17.
PAGE 73
Power supply specifications (per PSU) Power supply specifications (per PSU) Power supply model Maximum output power rating (DC) Input voltage Input line frequency Maximum input current Input line protection Maximum inrush current XBR-ACPWR-650-F 650 W 100-240V~ 50-60Hz 12 A Fuses 25A XBR-ACPWR-650-R 650 W 100-240V~ 50-60Hz 12 A Fuses 25A XBR-DCPWR-650-F 650 W -48 - -60V - 14 A Fuses 25A XBR-DCPWR-650-R 650 W -48 - -60V - 13.
PAGE 74
Serial port specifications (pinout - mini-USB) Serial port specifications (pinout - mini-USB) Pin Signal Description 1 Reserved Not used 2 UART0_RX Debug port (data received by SLX) 3 UART0_TX Console port (data transmitted by SLX) 4 Reserved Not used 5 GND Ground Serial port specifications (protocol) Parameter Value Baud 9600 Data bits 8 Parity None Stop bits 1 Flow control None Memory specifications Memory Type Size Main memory DDR4 16 GB Boot Flash NOR Flash 32 MB
PAGE 75
Regulatory compliance (safety) • EN 61000-3-3 Regulatory compliance (safety) • • • CAN/CSA-C22.2 No.
PAGE 76
Regulatory compliance (environmental) 66 Brocade SLX 9240 Switch Hardware Installation Guide 53-1004985-03
PAGE 77
Regulatory Statements • • • • • • • • USA (FCC CFR 47 Part 15 Warning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Industry Canada statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Europe and Australia (CISPR 32 Class A Warning) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 78
Japan (VCCI) Japan (VCCI) English translation of above statement This is Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
PAGE 79
China China English translation of above statement This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
PAGE 80
BSMI statement (Taiwan) BSMI statement (Taiwan) English translation of above statement Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
PAGE 81
Cautions and Danger Notices • • Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Danger notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Cautions A caution calls your attention to a possible hazard that can damage equipment.
PAGE 82
Cautions VORSICHT Stellen Sie sicher, dass an der Vorderseite, den Seiten und an der Rückseite der Luftstrom nicht behindert wird. MISE EN GARDE Vérifiez que rien ne restreint la circulation d'air devant, derrière et sur les côtés du dispositif et qu'elle peut se faire librement. PRECAUCIÓN Asegúrese de que el flujo de aire en las inmediaciones de las partes anterior, laterales y posterior del instrumento no esté restringido.
PAGE 83
Cautions CAUTION Use the screws specified in the procedure. Using longer screws can damage the device. VORSICHT Verwenden Sie die in der Anleitung aufgeführten Schrauben. Mit längeren Schrauben wird das Gerät möglicherweise beschädigt. MISE EN GARDE Utilisez les vis mentionnées dans les instructions. L'utilisation de vis plus longues peut endommager l'appareil. PRECAUCIÓN Utilice los tornillos especificados en el procedimiento. Si utiliza tornillos de mayor longitud, podría dañar el dispositivo.
PAGE 84
Cautions VORSICHT Netzteile sind hot-swap-fähig. Sie sollten jedoch eingesetzt oder entfernt werden, ohne dass ein Stromkabel mit einer Stromquelle verbunden ist, um Beschädigungen zu vermeiden. MISE EN GARDE Les unités d’alimentation sont permutables à chaud. Cependant, et pour éviter tout dommage, elles doivent être insérées ou retirées sans cordon d’alimentation relié à une source d’alimentation. PRECAUCIÓN Los proveedores de energía son deslizables por calor.
PAGE 85
Cautions CAUTION To avoid high voltage shock, do not open the device while the power is on. VORSICHT Das eingeschaltete Gerät darf nicht geöffnet werden, da andernfalls das Risiko eines Stromschlags mit Hochspannung besteht. MISE EN GARDE Afin d'éviter tout choc électrique, n'ouvrez pas l'appareil lorsqu'il est sous tension. PRECAUCIÓN Para evitar una descarga de alto voltaje, no abra el dispositivo mientras esté encendido.
PAGE 86
Danger notices VORSICHT Zur NEBS-konformen Installation eines Brocade Geräts mit Gleich- oder Wechselstrom betriebenen muss zur Erdung ein Kabel der Stärke von mindestens 6 AWG verwendet werden. Das Erdungskabel muss an einem Ende mit einem zugelassenen Crimp-Anschluss (im Lieferumfang des Geräts) versehen sein und mit dem anderen Ende an die Gebäude-Erde angeschlossen werden.
PAGE 87
Danger notices Un danger attire votre attention sur un risque possible de blessure ou de décès. Ci-dessous, vous trouverez les avertissements utilisés dans ce manuel. Una señal de peligro le llama la atención sobre cualquier posible peligro que pueda ocasionar daños personales o la muerte. A continuación se dan las advertencias utilizadas en este manual. DANGER The procedures in this manual are for qualified service personnel.
PAGE 88
Danger notices DANGER For safety reasons, the ESD wrist strap should contain a series 1 megohm resistor. GEFAHR Aus Sicherheitsgründen sollte ein EGB-Armband zum Schutz von elektronischen gefährdeten Bauelementen mit einem 1 Megaohm-Reihenwiderstand ausgestattet sein. DANGER Pour des raisons de sécurité, la dragonne ESD doit contenir une résistance de série 1 méga ohm. PELIGRO Por razones de seguridad, la correa de muñeca ESD deberá contener un resistor en serie de 1 mega ohmio.
PAGE 89
Danger notices DANGER Use safe lifting practices when moving the product. GEFAHR Beim Bewegen des Produktes ist auf eine sichere Hubtechnik zu achten. DANGER Utiliser des techniques de levage sûres pour déplacer le produit. PELIGRO Tenga mucho cuidado al levantar el producto para moverlo DANGER Mount the devices you install in a rack as low as possible. Place the heaviest device at the bottom and progressively place lighter devices above.
PAGE 90
Danger notices GEFAHR Verwenden Sie nur optische Transceiver, die von Brocade Communications Systems zugelassen sind und die die Anforderungen gemäß FDA Class 1 Radiation Performance Standards in 21 CFR, Unterkapitel I, sowie IEC 825 und EN60825 erfüllen. Optische Produkte, die diese Normen nicht erfüllen, können Strahlen aussenden, die für das menschliche Auge gefährlich sind. DANGER Utilisez uniquement des émetteurs-récepteurs optiques certifiés par Brocade Communications Systems, Inc.