Installation Guide
Table Of Contents
- Table of Contents
- Preface
- ExtremeSwitching 5520 Series Overview
- Port Partitioning
- Power Supplies for Use with Your Switch
- Expansion Modules
- Site Preparation
- Building Stacks
- Installing Your Switch
- Activating and Verifying the Switch
- Installing Expansion Modules
- Installing a V300 Virtual Port Extender
- Install a V300 Virtual Port Extender on a Wall
- Install a V300 Virtual Port Extender Under or on a Table Surface
- Install a V300 Virtual Port Extender in a VESA Mount
- Install a V300 in a Single Rack Mount
- Install a V300 in a Dual Rack Mount
- Install a V300 in a DIN Rail Mount
- Install a V300-8P-2T-W Model in a Single or Dual Rack Mount
- Installing a V300-8P-2T-W Model in a DIN Rail Mount
- Connecting the V300 Virtual Port Extender to Power
- Installing a V400 Virtual Port Extender
- Installing a Half-Duplex to Full-Duplex Converter
- Install a Versatile Interface Module in a 5520 Series Switch
- Installing a V300 Virtual Port Extender
- Replacing AC Power Supplies
- Replacing Fan Modules
- Monitoring the Device
- Technical Specifications
- ExtremeSwitching 5520 Series Technical Specifications
- V300 Virtual Port Extender Specifications
- V400 Virtual Port Extender Technical Specifications
- Half-Duplex to Full-Duplex Converter Technical Specifications
- 350 W AC Power Supplies Technical Specifications
- 715 W AC Power Supplies Technical Specifications
- 1100 W AC Power Supplies Technical Specifications
- 2000 W AC Power Supply Technical Specifications
- Power Cord Requirements for AC-Powered Switches and AC Power Supplies
- Console Connector Pinouts
- Safety and Regulatory Information
- Considerations Before Installing
- General Safety Precautions
- Maintenance Safety
- Fiber Optic Ports and Optical Safety
- Cable Routing for LAN Systems
- Installing Power Supply Units and Connecting Power
- Selecting Power Supply Cords
- Battery Notice
- Battery Warning - Taiwan
- EMC Warnings
- Japan (VCCI Class A)
- Korea EMC Statement
- Glossary
- Index
Table 43: 5520 Power Supply Options (continued)
Switch model Power supply Input rating
5520-24W switch
5520-12MW-36W
switch
5520-48W switch
1100 W AC power supply:
Part nos. XN-ACPWR-1100W-FB and 10941
1100 W AC PS FB (front to back)
Model PSSF112101A
100-127 V 200-240 V
50-60 Hz, 12/6 A max
per PS
5520-24W switch
5520-12MW-36W
switch
5520-48W switch
2000 W AC power supply:
Part nos. XN-ACPWR-2000W-FB and XN-
ACPWR-200W-F
2000 W AC PS FB (front to back)
Model PSSF202101A
100-127 V 200-240 V
50-60 Hz, 12/10 A max
per PS
Note
XN-ACPWR-xxx-FB PSUs cannot be used with the 10941, 10951, 10953, or XN-
ACPWR-2000W-F PSUs on the same switch.
The following are the minimum software versions that are required for use with XN-ACPWR-xxx-FB
PSUs and the switch:
• EXOS version 31.3.1, EXOS version 30.7.2 for X465 only
• VOSS version 8.3
Previous software versions are not supported with XN-ACPWR-xxx-FB PSUs. You must upgrade to the
listed minimum software version or later to use any of the XN-ACPWR-xxx-FB PSUs with the switch.
The following table lists supported PSU combinations when dual redundant PSUs are used on the
switch.
Refer to the 5520 datasheet for appropriate PSUs for the switch.
Table 44: PSU Redundancy Compatibility Notes
Switch Model Primary PSU Secondary PSU
Non-PoE models
XN-ACPWR-350W-FB XN-ACPWR-350W-FB
PoE models
XN-ACPWR-715W-FB or
XN-ACPWR-1100W-FB or
XN-ACPWR-2000W-FB
XN-ACPWR-715W-FB or
XN-ACPWR-1100W-FB or
XN-ACPWR-2000W-FB
Technical Specifications Power Options
ExtremeSwitching 5520 Series Hardware Installation Guide 129