Installation Guide
Table Of Contents
- Table of Contents
- Preface
- ExtremeSwitching 5520 Series Overview
- Port Partitioning
- Power Supplies for Use with Your Switch
- Expansion Modules
- Site Preparation
- Building Stacks
- Installing Your Switch
- Activating and Verifying the Switch
- Installing Expansion Modules
- Installing a V300 Virtual Port Extender
- Install a V300 Virtual Port Extender on a Wall
- Install a V300 Virtual Port Extender Under or on a Table Surface
- Install a V300 Virtual Port Extender in a VESA Mount
- Install a V300 in a Single Rack Mount
- Install a V300 in a Dual Rack Mount
- Install a V300 in a DIN Rail Mount
- Install a V300-8P-2T-W Model in a Single or Dual Rack Mount
- Installing a V300-8P-2T-W Model in a DIN Rail Mount
- Connecting the V300 Virtual Port Extender to Power
- Installing a V400 Virtual Port Extender
- Installing a Half-Duplex to Full-Duplex Converter
- Install a Versatile Interface Module in a 5520 Series Switch
- Installing a V300 Virtual Port Extender
- Replacing AC Power Supplies
- Replacing Fan Modules
- Monitoring the Device
- Technical Specifications
- ExtremeSwitching 5520 Series Technical Specifications
- V300 Virtual Port Extender Specifications
- V400 Virtual Port Extender Technical Specifications
- Half-Duplex to Full-Duplex Converter Technical Specifications
- 350 W AC Power Supplies Technical Specifications
- 715 W AC Power Supplies Technical Specifications
- 1100 W AC Power Supplies Technical Specifications
- 2000 W AC Power Supply Technical Specifications
- Power Cord Requirements for AC-Powered Switches and AC Power Supplies
- Console Connector Pinouts
- Safety and Regulatory Information
- Considerations Before Installing
- General Safety Precautions
- Maintenance Safety
- Fiber Optic Ports and Optical Safety
- Cable Routing for LAN Systems
- Installing Power Supply Units and Connecting Power
- Selecting Power Supply Cords
- Battery Notice
- Battery Warning - Taiwan
- EMC Warnings
- Japan (VCCI Class A)
- Korea EMC Statement
- Glossary
- Index
Figure 27: 5520-VIM Label
1 = 5520-VIM label
Table 11: 5520-VIM Matrix
5520-VIM-4X 5520-VIM-4XE 5520-VIM-4YE
Usable ports 4 4 4
Operational speeds 1Gbps & 10Gbps 1Gbps & 10Gbps 10Gbps & 25Gbps
PHY present No Yes Yes
1000BASE-T &
10GBASE-T
10GBASE-T only Both 10GBASE-T only
Mixed speeds 1Gbps & 10Gbps 1Gbps & 10Gbps Not supported
1
1G Auto-negotiation Disabled Enabled
10G Auto-negotiation Disabled Disabled Disabled
25G Auto-negotiation Enabled for DAC
Disabled for Fiber
FEC Not supported Not supported Auto-FEC enabled for
DAC and Fiber
2
MACsec Not supported 128/256bit 128/256bit
1
- In VOSS, you must set sys vim-speed to 10G or 25G for 5520-VIM-4YE. The default is 25G. A
reboot is not necessary after setting the speed.
1
- In EXOS, use the configure ports partition command with 4x25 or 4x10 on the first VIM
port.
2
- FEC is enabled by default only with autonegotiation set to ON.
See Versatile Interface Modules (VIM) Port LEDs on page 123 for VIM LED details.
5520-VIM-4X Versatile Interface Module
The 5520-VIM-4X versatile interface module provides four 10-GbE (SFP+) ports.
For information about the supported optical modules, refer to the most recent version of the Extreme
Optics website.
Expansion Modules
5520-VIM-4X Versatile Interface Module
ExtremeSwitching 5520 Series Hardware Installation Guide 33