Installation Guide
Table Of Contents
- ExtremeSwitching VDX 8770-4 Hardware Installation Guide
- Preface
- About This Document
- Product Overview
- Preparing for Installation
- Mounting the Device
- Mounting options
- Mounting precautions
- Unpacking, transporting, and installing the device
- Installing the 8U Chassis Flush Mount Rack Kit for Four-Post Racks (XBR-RMK-FL-4)
- Four-Post Flush and Recessed Mount Intake Air Duct Rack Kit Installation (XBR-RMK-FL-4DS-2 and XBR-RMK-RE-4DS-2)
- Installing the 8U Chassis Flush and Mid-Mount Rack Kit for Two-Post Racks (XBR-RMK-TELCO-4)
- Initial Configuration
- Configuration overview
- Providing power to the device
- Establishing a serial connection to the device
- Logging in to the serial console port
- Assigning permanent passwords
- Configuring the IP addresses
- Logging off the serial console port and disconnecting the serial cable
- Establishing an Ethernet connection
- Customizing a host name
- Customizing a chassis name
- Setting the date and time
- Changing the RBridge ID and VCS ID
- Configuring operating modes on 27x40 GbE line cards
- Verifying correct operation
- Backing up a running configuration
- Connecting network devices
- Installing transceivers and attaching cables
- Managing cables
- System Monitoring
- Removal and Replacement Procedures
- Introduction
- ESD precautions
- Cable management comb removal and replacement
- Line card removal and replacement
- CFP2 to QSFP28 Conversion Module removal and replacement
- Management module removal and replacement
- Switch fabric module removal and replacement
- Power supply removal and replacement
- Fan removal and replacement
- Air filter removal and replacement
- Module filler panel removal and replacement
- Chassis ID card removal and replacement
- SFP transceiver removal and replacement
- QSFP transceiver removal and replacement
- Cable routing table
- Air filter removal and replacement
- ExtremeSwitching VDX 8770 Technical Specifications
- System specifications
- Ethernet
- LEDs
- Other
- Weight and physical dimensions
- Environmental requirements
- Power supply specifications (per PSU)
- Power consumption (typical configuration)
- Power consumption (maximum configuration)
- Power consumption (modules)
- Data port specifications (Ethernet)
- Serial port specifications (pinout RJ-45)
- Serial port specifications (protocol)
- Memory specifications
- Regulatory compliance (EMC)
- Regulatory compliance (safety)
- Regulatory compliance (environmental)
- Regulatory Statements
- Cautions and Danger Notices
3. Noting that the rails are designated “Left” and “Right,” install each rail in the rack using four 10-32 x .63 screws, two screws on
each end of each rail. Refer the previous gure.
• Position the rails so that the adjustable ends are mounted on the intake aisle side of the rack.
• For rails with round holes - use two 10-32 x .63 screws with square-cone washers on each end of the rail assembly.
Tighten the screws to a torque of 29.2 to 36.5 in-lb (33.6 to 42 cm-kg).
• For rails with square holes - use the two standard 10-32 x .63 screws with blue Loctite on the threads and alignment
washers on each end of the rail assembly. Tighten the screws to a torque of 29.2 to 36.5 in-lb (33.6 to 42 cm-kg).
FIGURE 12 Rack mount rails installed in a four-post rack
1. 10-32 x .63 in. (1.60 cm) Phillips screws
Installing the 8U Chassis Flush Mount Rack Kit for Four-Post Racks (XBR-RMK-FL-4)
ExtremeSwitching VDX 8770-4 Hardware Installation Guide
36 9036110-00