Installation Avaya Virtual Services Platform 4000 Release 3.1 NN46251-300 Issue 02.
© 2014 Avaya Inc. All Rights Reserved. Notice While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time of printing, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information in this document without the obligation to notify any person or organization of such changes.
corporate employee, agent, subcontractor, or is not working on your company's behalf). Be aware that there can be a risk of Toll Fraud associated with your system and that, if Toll Fraud occurs, it can result in substantial additional charges for your telecommunications services.
Installation February 2014 Comments? infodev@avaya.
Contents Chapter 1: Avaya Virtual Services Platform 4000 regulatory information and safety precautions.......................................................................................................................... 7 International regulatory statements of conformity..................................................................................... 7 National electromagnetic compliance (EMC) statements of compliance.................................................. 7 FCC statement (USA only).....
Chapter 6: Translations of safety messages....................................................................
Chapter 1: Avaya Virtual Services Platform 4000 regulatory information and safety precautions International regulatory statements of conformity The Avaya Virtual Services Platform 4000 series was evaluated and is certified to the international regulatory standards for electromagnetic compliance (EMC) and safety and were found to have met the requirements for the following international standards: • EMC - Electromagnetic Emissions - CISPR 22, Class A • EMC - Electromagnetic Immunity - CISPR 24 • Electrical
Avaya Virtual Services Platform 4000 regulatory information and safety precautions ICES statement (Canada only) Canadian Department of Communications Radio Interference Regulations This digital apparatus (Avaya Virtual Services Platform 4000 Series) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
European Union and European Free Trade Association (EFTA) notice EN 55024 statement This is to certify that the Avaya Virtual Services Platform 4000 series equipment is shielded against the susceptibility to radio interference in accordance with the application of Council Directive 89/336/EEC. Conformity is declared by the application of EN 55024 (CISPR 24). EN 300386 statement The Avaya Virtual Services Platform 4000 series equipment complies with the requirements of EN 300386 V1.4.
Avaya Virtual Services Platform 4000 regulatory information and safety precautions BSMI statement (Taiwan only) This is a Class A product based on the standard of the Bureau of Standards, Metrology and Inspection (BSMI) CNS 13438 and CNS14336–1. MIC notice (Republic of Korea only) This device has been approved for use in Business applications only per the Class A requirements of the Republic of Korea Ministry of Information and Communications (MIC).
NOM statement (Mexico only) NOM statement (Mexico only) The following information is provided on the devices described in this document in compliance with the safety requirements of the Norma Oficial Méxicana (NOM): Exporter: Avaya Inc. 4655 Great America Parkway Santa Clara CA 95054 USA Importer: Avaya Communication de México, S.A. de C.V. Av. Presidente Masarik 111 Piso 6 Col Chapultepec Morales Deleg. Miguel HIdalgo México D.F.
Avaya Virtual Services Platform 4000 regulatory information and safety precautions Denan statement (Japan/Nippon only) National Environmental Statements of Compliance The WEEE Directive 2002/96/EC and RoHS (Restriction of Hazardous Substances) Directive 2002/95/EC sets collection, recycling and recovery targets for various categories of electrical products and their waste.
WEEE Directive Compliance Statement WEEE Directive Compliance Statement This product at end of life is subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore is marked with the symbol shown at the left. Treatment applied at end of life of these products in these countries shall comply with the applicable national laws implementing Directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE).
Avaya Virtual Services Platform 4000 regulatory information and safety precautions Voltage: Danger — High Voltage notices provide information about how to avoid a situation or condition that can cause serious personal injury or death from high voltage or electric shock. Danger: Danger notices provide information about how to avoid a situation or condition that can cause serious personal injury or death. 14 Installation February 2014 Comments? infodev@avaya.
Chapter 2: Introduction Purpose This guide provides information and instructions to install a Virtual Services Platform 4000 (VSP 4000) system. Related Resources Documentation See the Avaya Virtual Services Platform 4000 Documentation Roadmap, NN46251–100 for a list of the documentation for this product. Training Ongoing product training is available. For more information or to register, you can access the Web site at www.Avaya-learning.com.
Introduction • To find videos on the Avaya Support website, go to http://support.avaya.com, select the product name, and check the videos checkbox to see a list of available videos. • To find the Avaya Mentor videos on YouTube, go to http://www.youtube.com/ AvayaMentor and perform one of the following actions: - Enter a key word or key words in the Search Channel to search for a specific product or topic.
Chapter 3: New in this release There are no changes to the Avaya Virtual Services Platform 4000 Installation, NN46251–300, for release 3.1.
New in this release 18 Installation February 2014 Comments? infodev@avaya.
Chapter 4: Hardware compatibility The following tables describe the Avaya Virtual Services Platform 4000 hardware. Table 1: Hardware VSP 4000 model VSP 4850GTS Description • 48 10/100/1000 BaseTX RJ-45 ports Part number EC4800A78-E6 • two SFP ports • two SFP+ ports • Base Software License • one field replaceable 300W PSU VSP 4850GTS-PWR+ • Same content as EC4800A78-E6 with a EU power cord. EC4800B78-E6 • Same content as EC4800A78-E6 with a UK power cord.
Hardware compatibility VSP 4000 model VSP 4850GTS DC Description Part number • Same content as EC4800A88-E6 with a JP power cord. EC4800D88-E6 • Same content as EC4800A88-E6 with a NA power cord. EC4800E88-E6 • Same content a EC4800A88-E6 with a AU power cord.
Supported optical devices VSP 4000 PSU Usage Part number (order code) *Note: The seventh character (?) of the switch order number must be replaced with the proper letter to indicate desired product nationalization. See the following for details: “A”: No power cord included. “B”: Includes European “Schuko” power cord common in Austria, Belgium, Finland, France, Germany, The Netherlands, Norway, and Sweden. “C”: Includes power cord commonly used in the United Kingdom and Ireland.
Hardware compatibility Hardware Description Part number 1000BASE-LX (LC) DDI 1310 nm, Gigabit Ethernet, duplex LC AA1419049-E6 connector Range up to 10 km over single mode fiber (SMF); up to 550 m over multimode fiber (MMF) 1000BASE-XD DDI 1310 nm, Gigabit Ethernet, duplex LC connector AA1419050-E6 1550 nm, Gigabit Ethernet, duplex LC connector AA1419051-E6 1000BASE-ZX DDI 1550 nm, Gigabit Ethernet, duplex LC connector AA1419052-E6 1000BASE-XD CWDM (LC) 1470 nm to 1610 nm Range up to 40 km AA1
Supported optical devices Hardware Description Part number 10GBASE-SR/SW SFP+ 850 nm Range up to 300 m AA1403015-E6 10GBASE ZR/ZW SFP+ 1550 nm 70km SMF AA1403016-E6 10GBASE-ER CWDM SFP 1470 to 1610 nm with a range up to 40 AA1403153-E6 to + km AA1403160-E6 10GBASE-LRM SFP+ 220 m, 1260 to 1355 nm; 1310 nm nominal MMF AA1403017-E6 10GBase-CX 4-pair twinaxial copper cable that plugs AA1403018-E6 to into the SFP+ socket and connects two AA1403020-E6 10 Gb ports.
Hardware compatibility 24 Installation February 2014 Comments? infodev@avaya.
Chapter 5: Installing the Avaya Virtual Services Platform 4000 This section provides the information and procedures to install the Avaya Virtual Services Platform 4000. Installation fundamentals The VSP 4000 consists of: • 48 10/100/1000 Base TX ports - RJ-45 for the VSP 4850GTS and VSP 4850GTS DC models - 802.3at PoE+ for the VSP 4850GTS-PWR+ model • two combo SFP ports - These ports support copper and fiber on the same switch port. Only one medium type can be active at any time.
Installing the Avaya Virtual Services Platform 4000 1. VSP 4000 USB cover 2. Switch LEDs 3. 10/100/1000 ports (LEDs above ports) 4. Combo port SFP slots. Supports Avaya 1G SFPs and 100Base low speed SFPs. 5. SFP+ slots. Supports Avaya’s 1G SFPs and 10G SFP+s. 6. Console Port Figure 2: VSP 4850GTS-PWR+ 1. VSP 4000 USB cover 2. Switch LEDs 3. 10/100/1000 PoE+ ports (LEDs above ports) 4. Combo port SFP slots. Supports Avaya 1G SFPs and 100Base low speed SFPs. 5. SFP+ slots.
Electrostatic discharge designed and tested to withstand common mode ESD events, voltage can sometimes discharge to some connector pins, which can potentially damage the networking equipment. Caution: To protect the Avaya VSP 4000 against ESD damage, take the following measures before you connect data cables to the device: • Always use antistatic wrist straps. Make sure you adjust the strap to provide good skin contact.
Installing the Avaya Virtual Services Platform 4000 1. Connect the ground lug on the ESD discharge cable to a safe and suitable earth ground. 2. Connect all RJ-45 cable connectors to the female RJ-45 connector of the ESD discharge cable for at least 5 seconds, and then connect each RJ-45 cable connector to the switch. 3. Leave cables connected to the networking equipment. After you connect cables to networking equipment, the cables do not build up charge.
Package contents Environmental requirement Avaya Virtual Services Platform 4000 models • An adequate power source is within 6 feet (1.83 meters) of the switch. One 15-amp circuit is required for each power supply. • At least 2 inches (5.08 centimeters) of clearance on each side of the switch unit for ventilation. • Adequate clearance at the front and rear of the switch for access to cables. Warning: To avoid bodily injury from hazardous electrical shock and current, never remove the top of the device.
Installing the Avaya Virtual Services Platform 4000 Installing the Avaya Virtual Services Platform 4000 on a table or shelf You can install a single Avaya VSP 4000 switch on any flat surface. The surface must support the combined weight of the switch and attached cables (from 15 and 20 pounds [7 to 9 kilograms]). Caution: On a factory-supplied VSP 4000 switch, do not attempt to remove the USB device from the slot.
Installing the Avaya Virtual Services Platform 4000 in an equipment rack 2. Set the switch on a table or shelf as illustrated below. Allow at least 2 inches (5.1 centimeters) on each side for proper ventilation and at least 5 inches (12.7 centimeters) at the back for power cord clearance. Installing the Avaya Virtual Services Platform 4000 in an equipment rack To install an Avaya VSP 4000 switch in an equipment rack, perform this procedure.
Installing the Avaya Virtual Services Platform 4000 Prerequisites for installing the Avaya Virtual Services Platform 4000 in an equipment rack: • Ensure that you have a space of 1.75 inches (4.45 centimeters) in height for each switch in an EIA or IEC-standard 19-inch (48.2-centimeter) equipment rack. • The rack is bolted to the floor and braced if necessary. • The rack is grounded to the same grounding electrode used by the power service in the area.
Cable requirements for the Avaya Virtual Services Platform 4000 4. Insert and tighten the rack-mount screws. Cable requirements for the Avaya Virtual Services Platform 4000 The following table describes the cables required for a an Avaya Virtual Services Platform 4000 switch.
Installing the Avaya Virtual Services Platform 4000 Required Cable Description maximum length for the console port cable is 25 feet (8.3 meters). SFP Transceiver Ports Varies with the installed SFP transceiver. See the documentation shipped with the SFP transceiver for specifications. USB Port The USB port is not user accessible on the VSP 4000.
RJ-45 connector pin assignments 3. Slide the transceiver from the module slot. 4. If the transceiver does not slide easily from the module slot, use a gentle side-toside rocking motion while firmly pulling the transceiver from the slot. 5. Attach a dust cover over the fiber-optic bores and store the transceiver in a safe place until you need it. Important: Discard transceivers in accordance with the proper laws and regulations.
Installing the Avaya Virtual Services Platform 4000 Connector Pin Number 8 Signal Description Not applicable Not applicable Important: The Avaya VSP 4000 PWR+ models use pins 1, 2, 3, and 6 for PoE+, and is compliant with Type 2 (MDI-X) in IEEE802.3at. Console port pin assignments The following table describes the console port pin assignments in the Avaya VSP 4000. Important: Avaya VSP 4000 supports only CLI Quickstart use on the console port.
Power specifications for the Avaya Virtual Services Platform 4000 Connector Pin Number Signal 6 Receive data (RXD) — mandatory 7 Data set ready (DSR) — optional 8 Clear to send (CTS) — optional, can swap or link with pin 1 Power specifications for the Avaya Virtual Services Platform 4000 This section describes power specifications for the Avaya VSP 4000 switches.
Installing the Avaya Virtual Services Platform 4000 Avaya Virtual Services Platform power supply power specification Avaya Virtual Services Platform 4000 supports two external field replaceable power supplies. You can install a secondary power supply to provide redundancy, load sharing, and add Power over Ethernet Plus (PoE+) power budget on PWR+ models. For Avaya VSP 4000 AC and DC power supply order codes, see Power supplies on page 20.
Avaya Virtual Services Platform power supply power specification Figure 5: 300W power supply The 300W and 1000W AC power supplies use an IEC 60320 C16 AC power cord connector. The AC power cord is in close proximity to the hot air exhaust, and supports high operating temperatures. Figure 6: IEC 60320 C16 connector Power over Ethernet Plus specifications Model Maximum PoE+ W Avaya VSP 4850GTS— PWR+ models 855W with one power supply 15.4W (802.3af) 1855W with two power 17.8W (802.3.
Installing the Avaya Virtual Services Platform 4000 DC power supply specifications The following table describes the DC power supply specifications for the Avaya Virtual Services Platform 4000. For Avaya VSP 4000 AC and DC power supply order codes, see Power supplies on page 20.
Connect AC power Note: The switch chassis can prevent an incorrect installation of a power supply. If you insert a power supply upside down, it will not fully insert and the thumb screws will not engage. 4. Once you install a power supply, you can proceed with connecting AC power. Important: You can hot swap power supplies while the switch is operational. One power supply is required for continued switch operation.
Installing the Avaya Virtual Services Platform 4000 Country and Plug Specification Specifications Australia: • 240VAC • AS3112-1981 male plug • 50 Hz Typical Plug • Single phase Danger: Using power cords with a proper grounding path Use only power cords that have a grounding path. Without a proper ground, a person who touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the switch can result in excessive emissions.
Check Light Emitting Diode (LED) on the Avaya Virtual Services Platform 4000 Warning: Disconnecting the AC power cord is the only way to turn off AC power to the Avaya VSP 4000. Always connect the AC power cord in a quickly and safely accessible location in case of an emergency. For a translation of this statement, see Translations of safety messages on page 49.
Installing the Avaya Virtual Services Platform 4000 3. 10/100/1000 ports (LEDs above ports) 4. Combo port SFP slots. Supports Avaya 1G SFPs and 100Base low speed SFPs. 5. SFP+ slots. Supports Avaya’s 1G SFPs and 10G SFP+s. 6. Console Port Figure 9: VSP 4850GTS-PWR+ 1. VSP 4000 USB cover 2. Switch LEDs 3. 10/100/1000 PoE+ ports (LEDs above ports) 4. Combo port SFP slots. Supports Avaya 1G SFPs and 100Base low speed SFPs. 5. SFP+ slots. Supports Avaya’s 1G SFPs and 10G SFP+s. 6.
Check Light Emitting Diode (LED) on the Avaya Virtual Services Platform 4000 Label Status Color and Status Description Off The switch is not receiving power and not operating. Green (solid) • During start-up: The power-on self-test (POST) is complete and the switch is operating normally. • After start-up: The switch is running the agent code successfully. RPS Green (blinking) The switch is loading the agent software code.
Installing the Avaya Virtual Services Platform 4000 Table 14: RJ-45 Port LED state indicators Label Speed/PoE + Color and Status Description Green, Blink The port is set to operate at 1000 Mb/s with PoE. Green, Steady The port is set to operate at 1000 Mb/s without PoE +. Amber, Blink The port is set to operate at 100 Mb/s with PoE+. Amber, Steady The port is set to operate at 100 Mb/s without PoE+. Amber, Green Pulse The port is experiencing a PoE+ error.
Check Light Emitting Diode (LED) on the Avaya Virtual Services Platform 4000 Label Color and Status Description Green, Flashing SFP+ established and transmit/receive activity detected. Amber, Steady SFP detected and link established Amber, Flashing SFP established and transmit/receive activity detected. Amber, Blinking TX and RX blink together slowly to indicate a disabled port. Off No SFP or SFP+ connection detected.
Installing the Avaya Virtual Services Platform 4000 48 Installation February 2014 Comments? infodev@avaya.
Chapter 6: Translations of safety messages Caution: When you mount this device in a rack, do not stack units directly on top of one another. You must secure each unit to the rack with appropriate mounting brackets. Mounting brackets cannot support multiple units. Important: Achtung: Wenn diese Einheit in einem Rack montiert wird, muß ein gewisser Abstand zur nächsten Einheit gelassen werden. Jede Einheit muß mit geeignetem Befestigungsmaterial gesichert werden.
Translations of safety messages Caution: If you are not installing a module in the slot, be sure to keep the metal cover plate in place over the slot. Removing the cover plate impedes airflow and proper cooling of the unit. Important: Achtung: Wenn Sie kein Modul im Schacht verwenden, muß die Metallabdeckung über dem Schacht montiert sein. Eine Entfernung der Abdeckung führt zu einer Verschlechterung der Luftzirkulation und damit zu einer nicht ausreichenden Kühlung der Einheit.
Warning: Disconnecting the AC power cord is the only way to turn off AC power to this device. Always connect the AC power cord in a quickly and safely accessible location in case of an emergency. Important: Warnung: Das Gerät kann nur durch Ziehen des Netzsteckers ausgeschaltet werden. Schließen Sie das Netzkabel an einer Steckdose an, die in Notfällen schnell und sicher zugänglich ist.
Translations of safety messages Important: Vorsicht: Verwenden Sie nur Netzkabel mit Schutzerdung. Ohne ordnungsgemäße Schutzerdung besteht für Personen, die den Switch berühren, die Gefahr eines elektrischen Schlages. Eine nichtvorhandene Schutzerdung kann zu sehr starken Abstrahlungen führen. Danger: N'utilisez que des cordons d'alimentation équipés de trajet de mise à la terre. Sans mise à la terre adaptée, vous risquez de recevoir une décharge électrique en touchant le commutateur.
