Installation Instructions

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesFabric-enabled multi-service edge switches

Table Of Contents

Installation Job Aid for VSP 4450GTX-HT-

PWR+

Release 6.1.0.0

NN46251-305

Issue 02.01

November 2017

Notices

Notice paragraphs alert you about issues that require your attention. The following paragraphs

describe the types of notices used in this guide.

Note:

Notes provide tips and useful information regarding the installation and operation of products.

Electrostatic alert:

ESD

ESD notices provide information about how to avoid discharge of static electricity and

subsequent damage to products.

Caution:

Caution notices provide information about how to avoid possible service disruption or damage to

products.

Warning:

Warning notices provide information about how to avoid personal injury when working with

products.

Voltage:

Danger — High Voltage notices provide information about how to avoid a situation or condition

that can cause serious personal injury or death from high voltage or electric shock.

2017, Extreme Networks, Inc.

Summary of content (11 pages)

PAGE 1
Installation Job Aid for VSP 4450GTX-HTPWR+ Release 6.1.0.0 NN46251-305 Issue 02.01 November 2017 Notices Notice paragraphs alert you about issues that require your attention. The following paragraphs describe the types of notices used in this guide. Note: Notes provide tips and useful information regarding the installation and operation of products. Electrostatic alert: ESD ESD notices provide information about how to avoid discharge of static electricity and subsequent damage to products.
PAGE 2
Danger: Danger notices provide information about how to avoid a situation or condition that can cause serious personal injury or death. Safety messages Warning: Installation must be performed by qualified service personnel only. Read and follow all warning notices and instructions marked on the product or included in the documentation. Voltage: This equipment relies on the building's installation for overcurrent protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15 A U.S.
PAGE 3
Caution: Risk of high current and board burn out if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Warning: The lithium battery is not field replaceable. It must only be removed and replaced by authorized personnel. Contact Technical Support for assistance if the battery requires replacement.
PAGE 4
Installing the Virtual Services Platform 4000 on a table or shelf You can install a single VSP 4000 switch on any flat surface. The surface must support the combined weight of the switch and attached cables (from 15 and 20 pounds [7 to 9 kilograms]). Note: A factory-supplied 4450GTX-HT-PWR+ switch has a USB slot but no USB device or cover. To install a VSP 4000 on a table or shelf, perform this procedure. 1. Attach the included rubber footpads on the bottom of the switch at the locations indicated. 2.
PAGE 5
Installing the Virtual Services Platform 4000 in an equipment rack To install a VSP 4000 switch in an equipment rack, perform this procedure. Note: A factory-supplied 4450GTX-HT-PWR+ switch has a USB slot but no USB device or cover. Prerequisites for installing the VSP 4000 switch in an equipment rack: • Ensure that you have a space of 1.75 inches (4.45 centimeters) in height for each switch in an EIA or IEC-standard 19-inch (48.2-centimeter) equipment rack.
PAGE 6
3. Insert and tighten the rack-mount screws. Installing SFP transceivers Install SFP transceivers by performing this procedure. 1. Remove the transceiver from the protective packaging. 2. Verify that the transceiver is the correct model for the network configuration. 3. Grasp the transceiver between your thumb and forefinger. 4. Insert the transceiver into the proper module on the switch. Apply a light pressure to the transceiver until it clicks and locks into position in the module. 5.
PAGE 7
3. Slide the transceiver from the module slot. 4. If the transceiver does not slide easily from the module slot, use a gentle side-to-side rocking motion while firmly pulling the transceiver from the slot. 5. Attach a dust cover over the fiber-optic bores and store the transceiver in a safe place until you need it. Important: Discard transceivers in accordance with the proper laws and regulations.
PAGE 8
4450GTX-HT-PWR+ 860W between 0°C to 50°C 400W between 50°C to 70°C • With two operating PSUs, the maximum power consumption is: 1660W between 0°C to 50°C 832W between 50°C to 70°C Thermal Rating: 341.2 BTU/Hr typical and 494.
PAGE 9
Figure 1: 1000W AC power supply Connector The 1000W AC power supply uses an IEC 60320 C16 AC power cord connector. The AC power cord is in close proximity to the hot air exhaust, and supports high operating temperatures.
PAGE 10
Table 4: VSP 4450GTX-HT-PWR+ model with 2 PSUs 0°C to 50°C 50°C to 70°C 48 ports 48 ports PoE+ support on 48 ports 26 ports PoE support on • VSP 4450GTX-HT-PWR+ can support 802.3af 17.8W or 32.4W on each port with one power supply installed. You can add a second power supply for redundancy. Installing the VSP 4450GTX-HT-PWR+ power supply You must install at least one power supply before using the switch. VSP 4000 PWR+ models support two field replaceable external power supplies.
PAGE 11
Table 5: International power cord specifications Country and Plug Specification Specifications Continental Europe: • 220 or 230VAC • CEE7 standard VII male plug • 50 Hz • Harmonized cord (HAR marking on the outside of the cord jacket to comply with the CENELEC Harmonized Document HD-21) • Single phase United States of America, Canada, and Japan: • 100 or 120VAC • NEMA5-15P male plug • 50–60 Hz • UL-recognized (UL stamped on cord jacket) • Single phase Typical Plug • CSA-certified (CSA label s