Installation Avaya Virtual Services Platform 4000 Release 3.0.0.0 NN46251-300 Issue 01.
© 2013 Avaya Inc. All Rights Reserved. Notice While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time of printing, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information in this document without the obligation to notify any person or organization of such changes.
associated with your system and that, if Toll Fraud occurs, it can result in substantial additional charges for your telecommunications services. Avaya Toll Fraud intervention If you suspect that you are being victimized by Toll Fraud and you need technical assistance or support, call Technical Service Center Toll Fraud Intervention Hotline at +1-800-643-2353 for the United States and Canada. For additional support telephone numbers, see the Avaya Support website: http://support.avaya.com.
Installation May 2013 Comments? infodev@avaya.
Contents Chapter 1: Avaya Virtual Services Platform 4000 regulatory information and safety precautions.......................................................................................................................... 7 International regulatory statements of conformity..................................................................................... 7 National electromagnetic compliance (EMC) statements of compliance.................................................. 7 FCC statement (USA only).....
Installation May 2013
Chapter 1: Avaya Virtual Services Platform 4000 regulatory information and safety precautions International regulatory statements of conformity The Avaya Virtual Services Platform 4000 series was evaluated and is certified to the international regulatory standards for electromagnetic compliance (EMC) and safety and were found to have met the requirements for the following international standards: • EMC - Electromagnetic Emissions - CISPR 22, Class A • EMC - Electromagnetic Immunity - CISPR 24 • Electrical
Avaya Virtual Services Platform 4000 regulatory information and safety precautions ICES statement (Canada only) Canadian Department of Communications Radio Interference Regulations This digital apparatus (Avaya Virtual Services Platform 4000 Series) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
European Union and European Free Trade Association (EFTA) notice EN 55024 statement This is to certify that the Avaya Virtual Services Platform 4000 series equipment is shielded against the susceptibility to radio interference in accordance with the application of Council Directive 89/336/EEC. Conformity is declared by the application of EN 55024 (CISPR 24). EN 300386 statement The Avaya Virtual Services Platform 4000 series equipment complies with the requirements of EN 300386 V1.4.
Avaya Virtual Services Platform 4000 regulatory information and safety precautions BSMI statement (Taiwan only) This is a Class A product based on the standard of the Bureau of Standards, Metrology and Inspection (BSMI) CNS 13438 and CNS14336–1. MIC notice (Republic of Korea only) This device has been approved for use in Business applications only per the Class A requirements of the Republic of Korea Ministry of Information and Communications (MIC).
NOM statement (Mexico only) NOM statement (Mexico only) The following information is provided on the devices described in this document in compliance with the safety requirements of the Norma Oficial Méxicana (NOM): Exporter: Avaya Inc. 4655 Great America Parkway Santa Clara CA 95054 USA Importer: Avaya Communication de México, S.A. de C.V. Av. Presidente Masarik 111 Piso 6 Col Chapultepec Morales Deleg. Miguel HIdalgo México D.F.
Avaya Virtual Services Platform 4000 regulatory information and safety precautions Denan statement (Japan/Nippon only) National Environmental Statements of Compliance The WEEE Directive 2002/96/EC and RoHS (Restriction of Hazardous Substances) Directive 2002/95/EC sets collection, recycling and recovery targets for various categories of electrical products and their waste.
WEEE Directive Compliance Statement WEEE Directive Compliance Statement This product at end of life is subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore is marked with the symbol shown at the left. Treatment applied at end of life of these products in these countries shall comply with the applicable national laws implementing Directive 2002/96/EC on Waste of Electrical and Electronic Equipment (WEEE).
Avaya Virtual Services Platform 4000 regulatory information and safety precautions 14 Installation May 2013 Comments? infodev@avaya.
Chapter 2: Introduction Purpose This guide provides information and instructions to install a Virtual Services Platform 4000 (VSP 4000) system. Related Resources Documentation See the Avaya Virtual Services Platform 4000 Documentation Roadmap, NN46251–100 for a list of the documentation for this product. Training Ongoing product training is available. For more information or to register, you can access the Web site at www.Avaya-learning.com.
Introduction Support Visit the Avaya Support website at http://support.avaya.com for the most up-to-date documentation, product notices, and knowledge articles. You can also search for release notes, downloads, and resolutions to issues. Use the online service request system to create a service request. Chat with live agents to get answers to questions, or request an agent to connect you to a support team if an issue requires additional expertise. 16 Installation May 2013 Comments? infodev@avaya.
Chapter 3: New in this release Avaya Virtual Services Platform 4000 Installation, NN46251–300 is a new document for release 3.0.0.0, so all features are new in this release.
New in this release 18 Installation May 2013 Comments? infodev@avaya.
Chapter 4: Hardware compatibility The following tables describe the Avaya Virtual Services Platform 4000 hardware. Table 1: Hardware VSP 4000 model VSP 4850GTS Description • 48 10/100/1000 BaseTX RJ-45 ports Part number EC4800A78-E6 • two SFP ports • two SFP+ ports • Base Software License • one field replaceable 300W PSU VSP 4850GTS-PWR+ • Same content as EC4800A78-E6 with a EU power cord. EC4800B78-E6 • Same content as EC4800A78-E6 with a UK power cord.
Hardware compatibility VSP 4000 model VSP 4850GTS DC Description Part number • Same content as EC4800A88-E6 with a JP power cord. EC4800D88-E6 • Same content as EC4800A88-E6 with a NA power cord. EC4800E88-E6 • Same content a EC4800A88-E6 with a AU power cord.
Hardware Description Part number 10GBASE ZR/ZW SFP+ 1550 nm 70km SMF 10GBASE-ER CWDM SFP+ 1470 to 1610 nm with a range up to 40 km AA1403153-E6 to AA1403160-E6 10GBASE-LRM SFP+ 220 m, 1260 to 1355 nm; 1310 nm nominal AA1403017-E6 MMF 10GBase-CX 4-pair twinaxial copper cable that plugs into AA1403018-E6 the SFP+ socket and connects two 10 Gb ports. The maximum range is 10m. 10GBase-CX 4-pair twinaxial copper cable that plugs into AA1403019-E6 the SFP+ socket and connects two 10 Gb ports.
Hardware compatibility Hardware 100BASE-FX SFP Description 1310 nm, LC connector Part number AA1419074-E6 Important: Avaya recommends the use of Avaya branded SFP and SFP+ transceivers as they have been through extensive qualification and testing. Avaya will not be responsible for issues related to non-Avaya branded SFP and SFP+ transceivers. 22 Installation May 2013 Comments? infodev@avaya.
Chapter 5: Installing the Avaya Virtual Services Platform 4000 This section provides the information and procedures to install the Avaya Virtual Services Platform 4000. Installation fundamentals The VSP 4000 consists of: • 48 10/100/1000 Base TX ports - RJ-45 for the VSP 4850GTS and VSP 4850GTS DC models - 802.3at PoE+ for the VSP 4850GTS-PWR+ model • two combo SFP ports - These ports support copper and fiber on the same switch port. Only one medium type can be active at any time.
Installing the Avaya Virtual Services Platform 4000 Figure 1: VSP 4850GTS 1. VSP 4000 USB cover 2. Switch LEDs 3. 10/100/1000 ports (LEDs above ports) 4. Combo port SFP slots. Supports Avaya 1G SFPs and 100Base low speed SFPs. 5. SFP+ slots. Supports Avaya’s 1G SFPs and 10G SFP+s. 6. Console Port Figure 2: VSP 4850GTS-PWR+ 1. VSP 4000 USB cover 2. Switch LEDs 3. 10/100/1000 PoE+ ports (LEDs above ports) 4. Combo port SFP slots. Supports Avaya 1G SFPs and 100Base low speed SFPs. 5. SFP+ slots.
Electrostatic discharge Electrostatic discharge This section provides information and procedures to prevent electrostatic discharge during installation. Preventing electrostatic discharge damage Electrostatic discharge (ESD) is a discharge of stored static electricity that can damage equipment and impair electrical circuitry. Electrostatic voltages can result from friction including, pulling cabling through conduits, walking across carpeted areas, and building static charge in clothing.
Installing the Avaya Virtual Services Platform 4000 Figure 3: Job aid To install the ESD discharge cable, perform this procedure. 1. Connect the ground lug on the ESD discharge cable to a safe and suitable earth ground. 2. Connect all RJ-45 cable connectors to the female RJ-45 connector of the ESD discharge cable for at least 5 seconds, and then connect each RJ-45 cable connector to the switch. 3. Leave cables connected to the networking equipment.
Package contents Environmental requirement Avaya Virtual Services Platform 4000 models Storage Relative Humidity 10 to 90 percent noncondensing Maximum Operating Altitude 3,048m (10 000 feet) above sea level Altitude 0 to 3,048m (0 to 10,000ft) above sea level Storage Altitude 0 to 12,192m (0 to 40,000ft) above sea level Acoustic Noise Less than or equal to 45 db at 35°C and less than or equal to 57 db at 50°C. The temperature is allowed to have ±3.
Installing the Avaya Virtual Services Platform 4000 • Screws to attach the switch to the equipment rack 3. Rubber footpads 4. AC power cord 5. Documentation Note: Cable trays can be provided as an option. Installing the Avaya Virtual Services Platform 4000 on a table or shelf You can install a single Avaya VSP 4000 switch on any flat surface. The surface must support the combined weight of the switch and attached cables (from 15 and 20 pounds [7 to 9 kilograms]).
Installing the Avaya Virtual Services Platform 4000 in an equipment rack 2. Set the switch on a table or shelf as illustrated below. Allow at least 2 inches (5.1 centimeters) on each side for proper ventilation and at least 5 inches (12.7 centimeters) at the back for power cord clearance. Installing the Avaya Virtual Services Platform 4000 in an equipment rack To install an Avaya VSP 4000 switch in an equipment rack, perform this procedure.
Installing the Avaya Virtual Services Platform 4000 Prerequisites for installing the Avaya Virtual Services Platform 4000 in an equipment rack: • Ensure that you have a space of 1.75 inches (4.45 centimeters) in height for each switch in an EIA or IEC-standard 19-inch (48.2-centimeter) equipment rack. • The rack is bolted to the floor and braced if necessary. • The rack is grounded to the same grounding electrode used by the power service in the area.
Cable requirements for the Avaya Virtual Services Platform 4000 Cable requirements for the Avaya Virtual Services Platform 4000 The following table describes the cables required for a an Avaya Virtual Services Platform 4000 switch.
Installing the Avaya Virtual Services Platform 4000 SFP transceiver use and designation, see Installation — SFP and SFP+ transceivers, Avaya Virtual Services Platform 4000, NN46251–301 . Installing SFP transceivers Install SFP transceivers by performing this procedure. 1. Remove the transceiver from the protective packaging. 2. Verify that the transceiver is the correct model for the network configuration. 3. Grasp the transceiver between your thumb and forefinger. 4.
RJ-45 connector pin assignments RJ-45 connector pin assignments The following section describes the connector pin assignments for the RJ-45 connectors in the Avaya Virtual Services Platform 4000. Avaya Virtual Services Platform 4000 Switch 4850GTS-PWR+ The following table describes the Power over Ethernet Plus RJ-45 connector pin assignments in the Avaya VSP 4000 4850GTS-PWR+.
Installing the Avaya Virtual Services Platform 4000 Table 6: DB–9 Console port pin assignments Connector Pin Number Signal 1 Carrier detect (not used) 2 Transmit Data (TXD) 3 Receive Data (RXD) 4 Data terminal ready (not used) 5 Signal ground (GND) 6 Not used 7 Request to send (not used) 8 Not used 9 Ring indicator (not used) Table 7: RJ–45 Console port pin assignments Connector Pin Number Signal 1 Ready to send (RTS) — optional 2 Data terminal ready (DTR) — optional, can swap or
Avaya Virtual Services Platform power supply power specification Avaya Virtual Services Platform 4000 Switch 4850GTS and 4850GTS-PWR+ The following table describes the regulatory AC power specifications for the Avaya Virtual Services Platform 4000 4850GTS and 4850GTS-PWR+ switches. It should be noted that regulatory power specifications are based on the maximum rated capacity of the power supplies and are not based on typical power consumption which is typically lower.
Installing the Avaya Virtual Services Platform 4000 Figure 4: 1000W power supply The Avaya VSP 4850GTS supports 300W AC power supplies. Figure 5: 300W power supply The 300W and 1000W AC power supplies use an IEC 60320 C16 AC power cord connector. The AC power cord is in close proximity to the hot air exhaust, and supports high operating temperatures Figure 6: IEC 60320 C16 connector 36 Installation May 2013 Comments? infodev@avaya.
Installing the Avaya Virtual Services Platform 4000 power supply Power over Ethernet Plus specifications Model Maximum PoE+ W Average PoE+ W on 50 port models Avaya VSP 4850GTS— PWR+ models 855W with one power supply 15.4W (802.3af) 1855W with two power 17.8W (802.3.at) — 1 power supplies supply 32.4W (802.3at) — 2 power supplies • VSP 4850GTS-PWR+ can support 802.3af 15.4W on each port with one power supply installed. You can add a second power supply for redundancy.
Installing the Avaya Virtual Services Platform 4000 Perform the following procedure to install an external power supply into your switch. Note: Avaya VSP 4000 hardware can vary. This procedure only applies to hardware models with field replaceable power supplies. 1. If a blanking plate covers the required power supply slot, remove the blanking plate before attempting to insert the power supply. 2. Insert each power supply into a rear power supply slot. 3.
Connect AC power Country and Plug Specification Specifications Typical Plug • CEE7 standard VII male plug • Harmonized cord (HAR marking on the outside of the cord jacket to comply with the CENELEC Harmonized Document HD-21) United States of America, Canada, and Japan: • 100 or 120VAC • NEMA5-15P male plug • 50–60 Hz • UL-recognized (UL stamped on cord jacket) • Single phase • CSA-certified (CSA label secured to the cord) United Kingdom: • 240VAC • BS1363 male plug with fuse • 50 Hz • Harmoniz
Installing the Avaya Virtual Services Platform 4000 Figure 7: Connecting AC power to the back panel Warning: Disconnecting the AC power cord is the only way to turn off AC power to the Avaya VSP 4000. Always connect the AC power cord in a quickly and safely accessible location in case of an emergency. For a translation of this statement, see Translations of safety messages on page 45.
Check Light Emitting Diode (LED) on the Avaya Virtual Services Platform 4000 For detailed explanations of the states indicated by each front panel LED type, see the following sections: • Port LED state indicators on page 43 • Switch LED state indicators on page 42 Figure 8: VSP 4850GTS 1. VSP 4000 USB cover 2. Switch LEDs 3. 10/100/1000 ports (LEDs above ports) 4. Combo port SFP slots. Supports Avaya 1G SFPs and 100Base low speed SFPs. 5. SFP+ slots. Supports Avaya’s 1G SFPs and 10G SFP+s. 6.
Installing the Avaya Virtual Services Platform 4000 6. Console Port Warning: Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber-optic cables are connected to a light source. For a translation of this statement, see Translations of safety messages on page 45. Switch LED state indicators The following figure describes the main switch LED state indications provided by LED color and fluctuation cues.
Check Light Emitting Diode (LED) on the Avaya Virtual Services Platform 4000 Label Color and Status Off Description No power to secondary power supply. The switch is not connected to an RPS or secondary power supply. The RPS is not supplying power, or the DC/DC module is not supplying power.. Port LED state indicators This section describes the port LED state indicators by color and fluctuation cues.
Installing the Avaya Virtual Services Platform 4000 Label Color and Status Description Green, Steady The SFP port and the transmit port are active. Amber, Blink Not applicable. Amber, Steady SFP Installed—TX Port Inactive Off No SFP transceiver is present. Link / Activity Green, Blink Activity exists on the port. Green, Slow Blink Software disabled this port. Green, Steady The link is operating normally. Off No link exists.
Chapter 6: Translations of safety messages Caution: When you mount this device in a rack, do not stack units directly on top of one another. You must secure each unit to the rack with appropriate mounting brackets. Mounting brackets cannot support multiple units. Important: Achtung: Wenn diese Einheit in einem Rack montiert wird, muß ein gewisser Abstand zur nächsten Einheit gelassen werden. Jede Einheit muß mit geeignetem Befestigungsmaterial gesichert werden.
Translations of safety messages Caution: If you are not installing a module in the slot, be sure to keep the metal cover plate in place over the slot. Removing the cover plate impedes airflow and proper cooling of the unit. Important: Achtung: Wenn Sie kein Modul im Schacht verwenden, muß die Metallabdeckung über dem Schacht montiert sein. Eine Entfernung der Abdeckung führt zu einer Verschlechterung der Luftzirkulation und damit zu einer nicht ausreichenden Kühlung der Einheit.
Warning: Disconnecting the AC power cord is the only way to turn off AC power to this device. Always connect the AC power cord in a quickly and safely accessible location in case of an emergency. Important: Warnung: Das Gerät kann nur durch Ziehen des Netzsteckers ausgeschaltet werden. Schließen Sie das Netzkabel an einer Steckdose an, die in Notfällen schnell und sicher zugänglich ist.
Translations of safety messages Important: Avviso: L'unico modo per disattivare questo dispositivo consiste nello scollegare il cavo di alimentazione. Collegare sempre il cavo di alimentazione ad una presa che sia facilmente e rapidamente accessibile in caso di emergenza. Danger: Use only power cords that have a grounding path. Without a proper ground, a person who touches the switch is in danger of receiving an electrical shock. Lack of a grounding path to the switch can result in excessive emissions.