Installing Transceivers and Optical Components on VSP Operating System Software Release 6.0.1 NN47227-301 Issue 08.
© 2018, Avaya Inc. All Rights Reserved. Notice While reasonable efforts have been made to ensure that the information in this document is complete and accurate at the time of printing, Avaya assumes no liability for any errors. Avaya reserves the right to make changes and corrections to the information in this document without the obligation to notify any person or organization of such changes.
documentation, Hosted Service, and the product provided by Avaya including the selection, arrangement and design of the content is owned either by Avaya or its licensors and is protected by copyright and other intellectual property laws including the sui generis rights relating to the protection of databases. You may not modify, copy, reproduce, republish, upload, post, transmit or distribute in any way any content, in whole or in part, including any code and software unless expressly authorized by Avaya.
Contents Chapter 1: Introduction............................................................................................................ 6 Purpose.................................................................................................................................. 6 Chapter 2: New in this document............................................................................................ 7 Release 6.0.1..........................................................................................
Contents SFP+ labels.................................................................................................................... 41 General SFP+ specifications............................................................................................ 41 Supported SFP+ transceivers........................................................................................... 42 Chapter 8: QSFP+.............................................................................................................
Chapter 1: Introduction Purpose This document provides installation instructions and technical specifications for the following: • Small Form Factor Pluggable (SFP) • Small Form Factor Pluggable plus (SFP+) • Quad Small Form Factor Pluggable plus (QSFP+) VOSS runs on the following product familes: • Avaya Virtual Services Platform 4000 Series • Avaya Virtual Services Platform 7200 Series • Avaya Virtual Services Platform 8000 Series Not all products support all cable lengths, or all SFP, SFP+, or QSFP+ tra
Chapter 2: New in this document The following sections detail what is new in Installing Transceivers and Optical Components on VSP Operating System Software, NN47227-301. Release 6.0.1 40-gigabit Ethernet Quad Small Form Factor Pluggable plus transceiver module VOSS 6.0.1 adds the 40GBASE-SR4 extended reach Quad Small Form Factor Pluggable plus (QSFP+) transceiver module. The 40GBASE-SR4 extended reach transceiver provides a highspeed link at an aggregate signaling rate. The part number is AA1404006-E6.
Chapter 3: Safety and equipment care information This chapter contains important safety and regulatory information. Read this section before you install a transceiver. Fiber optic equipment care Use the information in this section to properly maintain and care for fiber optic equipment. Transceivers are static sensitive. Dust contamination can reduce the performance of optical parts in transceivers.
Fiber optic connector care Use the following precautions to avoid damaging the glass fiber: • Do not kink, knot, or vigorously flex the cable. • Do not bend the cable to less than a 40 mm radius. • Do not stand on fiber optic cable; keep the cable off the floor. • Do not pull fiber optic cable harder than you do a cable containing copper wire of comparable size. • Do not allow a static load of more than a few pounds on a section of the cable.
Safety and equipment care information Danger: Risk of eye injury When you inspect a connector, ensure that light sources are off. The light source in fiber optic cables can damage your eyes. • If you suspect only the possibility of dust particles, for example, if you leave a connector uncapped in a clean environment, use high-quality canned air or a reel cleaner, for example, a Cletop, to clean the connector. A reel cleaner is a good choice to ensure that no dust contaminates the connector.
Cleaning duplex connectors To avoid getting debris in your eyes, wear safety glasses when you work with the canned air duster. To avoid eye irritation on contact, wear safety glasses when you work with isopropyl alcohol. Procedure 1. Remove dust or debris by applying canned air to the cylindrical and end-face surfaces of the connector. 2. Gently wipe the cylindrical and end-face surfaces with a tissue dampened with optical-grade isopropyl alcohol. 3.
Safety and equipment care information To avoid getting debris in your eyes, wear safety glasses when you work with the canned air duster. To avoid eye irritation on contact, wear safety glasses when you work with isopropyl alcohol. Procedure 1. Remove or retract the shroud. On removable shroud connectors, hold the shroud on the top and bottom at the letter designation, apply medium pressure, and then pull it free from the connector body. Do not discard the shroud.
Cleaning receptacles Warning: Risk of equipment damage To avoid contamination, only clean optical ports if you see evidence of contamination or reduced performance exists, or during their initial installation. To prevent oil contamination of connectors, use only high-quality canned compressed air. Do not allow the air extension tube to touch the bottom of the optical port. Procedure 1. Remove dust or debris by blowing canned air into the optical port of the device using the canned air extension tube. 2.
Chapter 4: Supported transceiver, BOCs, and DACs information Supported transceivers The following sections show supported SFP, SFP+, and QSFP+ transceivers for VOSS. The tables display only transceivers that are currently supported and available in the price book. Not all Avaya Ethernet switching and routing products support all the transceivers listed in this section.
Supported transceivers Model Description Minimum software version Part number VSP 4000 VSP 7200 VSP 8200 VSP 8400 1000BASE-T SFP gigabit Ethernet, RJ–45 connector 3.0.0.0 4.2.1 4.0.0 4.2.0 AA1419043–E6 1000BASE-SX DDI SFP 850 nm, gigabit Ethernet, duplex LC connector 3.0.0.0 4.2.1 4.0.0 4.2.0 AA1419048–E6 1000BASE-LX DDI SFP 1310 nm, gigabit Ethernet, duplex LC connector 3.0.0.0 4.2.1 4.0.0 4.2.0 AA1419049–E6 1000BASE-BX10 1310 nm (tx) and DDI SFP 1490 nm (rx) 3.0.0.0 4.2.
Supported transceiver, BOCs, and DACs information Model Description Minimum software version Part number VSP 4000 VSP 7200 VSP 8200 VSP 8400 5 °C to +85 °C) SFP+ 10GBASEER/EW SFP+ 40 km, 1550 nm SMF 3.0.0.0 4.2.1 4.0.0 4.2.0 AA1403013–E6 10GBASEZR/ZW SFP+ 70 km, 1550 nm SMF 3.0.0.0 N/A * 4.0.0 4.2.0 AA1403016–E6 10GBASE-LRM SFP+ 220 m, 1260 to 1355 nm; 1310 nm nominal MMF 3.0.0.0 4.0.0 4.2.
Supported DACs and BOCs Table 3: QSFP+ transceivers Model Description Minimum software version Part number VSP 4000 VSP 7200 VSP 8200 VSP 8400 40GBASE-SR4 100 meters with 4x10GBASE-SR OM3 fiber cable QSFP+ 150 meters with OM4 fiber cable N/A 4.2.1 4.0.0 4.2.0 AA1404005–E6 40GBASE-SR4 extended reach QSFP+ 300 meters with OM3 fiber cable N/A 6.0.1 6.0.1 6.0.1 AA1404006–E6 40GBASE-LR4 QSFP+ 10 km N/A 4.2.1 4.0.0 4.2.0 AA1404001–E6 40GBASE-ER4 QSFP+ 40 km N/A 4.2.1 4.2.1 4.2.
Supported transceiver, BOCs, and DACs information Important: The VSP switches operate in forgiving mode for QSFP+ direct attach cables (DAC), which means that the switch will bring up the port operationally when using non-Avaya direct attach cables. Avaya does not provide support for operational issues related to these DACs, but they will operate and the port link will come up. SFP+ direct attach cable specifications The following table provides a list of the supported SFP+ direct attach cables (DAC).
Supported DACs and BOCs provide support for operational issues related to these DACs, but they will operate and the port link will come up. The following table provides a list of the supported QSFP+ to QSFP+ DACs. Cable type Cable length Minimum software version Part number VSP 4000 VSP 7200 VSP 8200 VSP 8400 Passive flexiDAC (TAA) QSFP+ to QSFP+ DAC 0.5 meter N/A 4.2.1 4.0.0 4.2.0 AA1404037– E6 Passive copper DAC QSFP+ to QSFP+ DAC 1 meter N/A 4.2.1 4.0.0 4.2.
Supported transceiver, BOCs, and DACs information Figure 1: Active optical BOC Passive copper BOCs—The length from the nose of the QSFP+ connector to the fanout of the four copper pigtails is 10.2 cm. The total cable length can be 1, 3, or 5 meters. Figure 2: Passive copper BOC The following tables provide a list of active and passive BOCs, and includes the part numbers and minimum software version supported.
Chapter 5: Optical routing design Optical routing design The Avaya optical routing system uses coarse wavelength division multiplexing (CWDM) in a grid of eight optical wavelengths. Use the Avaya optical routing system to maximize bandwidth on a single optical fiber. This chapter provides optical routing system information that you can use to help design your network.
Optical routing design The Avaya optical routing system supports both ring and point-to-point configurations. The optical routing system includes the following parts: • CWDM SFPs • Optical add/drop multiplexers (OADM) • Optical multiplexer/demultiplexers (OMUX) • Optical shelf to house the multiplexers OADMs drop or add a single wavelength from or to an optical fiber. For the list of supported optical devices for the current release, see Supported optical devices on page 22.
Optical routing design Optical power considerations When you connect the device to collocated equipment, ensure that enough optical attenuation exists to avoid overloading the receivers of each device. You must consider the minimum attenuation requirement based on the specifications of third-party equipment. .
Optical routing design operation, or calculate budget and losses using actual values rather than specified limit values. Either method can improve the link budget by 4 to 5 dB or more. January 2018 Installing Transceivers and Optical Components on VOSS Comments on this document? infodev@avaya.
Chapter 6: SFP This chapter provides installation procedures and specifications for Small Form Factor Pluggable (SFP) transceivers. SFP transceivers This section describes how to select and install Small Form Factor Pluggable (SFP) transceivers. Use an SFP transceiver for 1 Gigabit per second (Gbps) Ethernet connections. The Avaya VSP 8200 supports SFP transceivers on ports 1/1-1/40 and 2/1-2/40.
SFP enabled. If not, the link will not be established. Also note that because the SFP+ ports on the VSP 7254XSQ only support 1 and 10 Gbps speeds, the AA1419043-E6 1000BASE-T SFP will only operate at 1G speeds. If you use 1 Gbps fiber SFP transceivers, auto-negotiation is always disabled so the remote end must also have auto-negotiation disabled. Otherwise this is not a supported configuration with VSP 7254XSQ.
SFP transceivers • Avaya recommends the use of Avaya branded SFP transceivers as they have been through extensive qualification and testing. Avaya will not be responsible for issues related to non-Avaya branded SFP transceivers. Installing an SFP Install an SFP to provide an interface between the device and the network cable. Before you begin • Verify that the SFP is the correct model for your network configuration. • Before you install the fiber, ensure that the connector is clean.
SFP 4. Remove the dust cover from the optical bore, and insert the fiber optic connector. Example The following figure shows an example installation of a bore plug transceiver with the bail latch facing up. The figure does not represent a specific product. Job aid Depending on the transceiver manufacturer, the SFP transceiver can use different types of locking and extractor mechanisms.
SFP specifications Before you begin • Wear an antistatic wrist strap. Danger: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber optic cables connect to a light source. Electrostatic alert: ESD can damage electronic circuits. Do not touch electronic hardware unless you wear a grounding wrist strap or other static-dissipating device. Procedure 1.
SFP Important: The switch operates in forgiving mode for SFP transceivers, which means that the switch will bring up the port operationally when using non-Avaya SFP transceivers. Avaya does not provide support for operational issues related to these SFP transceivers, but they will operate and the port link will come up. The switch logs the device as an unsupported or unknown device.
SFP specifications Supported SFP transceivers The following section provides specifications for the supported SFP transceivers. Autonegotiation Use Autonegotiation to allow the device to automatically negotiate the best common data rate and duplex mode to use between two Autonegotiation-capable Ethernet devices. 1000BASE-T SFP specifications The 1000BASE-T SFP provides Gigabit Ethernet connectivity using a single eight-pin RJ-45 connector.
SFP Parameter Specifications Link optical power budget 7.5 dB Transmitter characteristics Launch power –9.5 to –4.0 dBm Receiver characteristics Receiver sensitivity –17 dBm Maximum receiver power 0 dBm 1000BASE-LX DDI SFP specifications This SFP transceiver provides 1000BASE-LX Gigabit Ethernet connectivity at 1310 nanometers (nm) using single mode or multimode optical fiber. The part number is AA1419049-E6.
SFP specifications The long wavelength optical transceivers used in these models provide variable distance ranges using single mode fiber optic cabling. You can use 1000BASE-BX SFP transceivers to double the number of your fiber links. For example, if you install 20 fiber pairs with 20 conventional ports connected, you can use 1000BASE-BX SFP transceivers to expand to 40 ports, using the same fiber. The following table provides the reach and part numbers for each mating pair.
SFP Parameter Specification Maximum input power (maximum average receive power) –3.0 dBm 1000BASE-BX40 bidirectional SFP specifications The 1000BASE-BX40 SFP transceivers (part numbers AA1419076-E6 and AA1419077-E6) can attain a reach of up to 40 km. The minimum IL is 6 dB. The following table describes standards, connectors, cabling, and distances for the 1000BASEBX40 SFP transceiver.
SFP specifications Parameter Specifications Connectors Duplex LC Cabling • 62.5 µm MMF optic cable • 50 µm MMF optic cable Distance • Up to 2 km using 500 MHz-km MMF optic cable Wavelength 1300 nm Link optical power budget 10 dB Transmitter characteristics Maximum launch power –14 dBm Minimum launch power –23.5 to –20 dBm Receiver characteristics Receiver sensitivity –33.
Chapter 7: SFP+ This chapter provides installation procedures and specifications for Small Form Factor Pluggable plus (SFP+) transceivers. SFP+ transceivers This section describes how to select and install Small Form Factor Pluggable plus (SFP+) transceivers. Use an SFP+ transceiver to connect a device motherboard to fiber optic or direct attach cables, up to 15 meters in length.
SFP+ transceivers basic displays the corresponding vendor names instead of leaving the vendor name blank as in the releases prior to VOSS 4.2.1. • Avaya recommends the use of Avaya branded SFP and SFP+ transceivers as they have been through extensive qualification and testing. Avaya will not be responsible for issues related to non-Avaya branded SFP and SFP+ transceivers. Selecting an SFP+ Use an SFP+ transceiver for 10 Gigabit per second (Gbps) Ethernet connections over optical fiber.
SFP+ Before you begin Important: Do not install an SFP+ transceiver in an SFP slot. The two transceivers look the same but function differently. Ensure the slot is an SFP+ slot. • Verify that the SFP+ transceiver is the correct model for your network configuration. • Before you install the fiber, ensure that the connector is clean. Danger: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port.
SFP+ transceivers Example Job aid Depending on the transceiver manufacturer, the SFP+ transceiver uses bail-latch type of locking and extractor mechanism. The following figure shows typical mechanism used on SFP+ transceivers; other locking and extractor mechanisms exist. SFP+ transceivers are similar to SFP transceivers in physical appearance. In the following figure, the SFP+ transceiver still contains the bore plug. Pull the bail to release the device.
SFP+ Danger: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber optic cables connect to a light source. Electrostatic alert: ESD can damage electronic circuits. Do not touch electronic hardware unless you wear a grounding wrist strap or other static-dissipating device. Procedure 1. Disconnect the network fiber optic cable from the SFP+ connector. 2.
SFP+ specifications • Avaya recommends the use of Avaya branded SFP and SFP+ transceivers as they have been through extensive qualification and testing. Avaya will not be responsible for issues related to non-Avaya branded SFP and SFP+ transceivers. SFP+ labels The typical Avaya SFP+ transceiver has a label on the top and bottom or side of the transceiver. The following figures show example labels.
SFP+ Parameter Specifications Storage temperature –40 to 85 ºC Operating temperature 0 to 70 ºC for RoHS -E6 models up to 85 ºC for high temperature models Supported SFP+ transceivers The following section provides specifications for the supported SFP+ transceivers. 10GBASE-T SFP+ transceiver The 10GBASE-T SFP+ transceiver provides 10 Gigabit Ethernet connectivity using a single eight pin RJ-45 connector. The 10GBASE-T SFP+ only operates at 10 Gigabits per second (Gbps) speed.
SFP+ specifications Parameter Specifications Maximum transmitter and dispersion penalty 3.2 dB at 10 km Transmitter characteristics Line rate (nominal 10GBASE-LR 10.3125 Gbps ±100 ppm (10 GbE) Average launch power –8.2 to 0.5 dBm Minimum launch power in OMA minus transmission and dispersion penalty (TDP) –6.2 dBm Minimum optical modulation amplitude –5.2 dBm Minimum extinction ratio 3.
SFP+ Parameter Specifications Transmitter characteristics Line rate (nominal) 10GBASE-LR 10.3125 Gbps ±100 ppm (10 GbE) Average launch power –8.2 to 0.5 dBm Minimum launch power in OMA minus transmission and dispersion penalty (TDP) –6.2 dBm Minimum optical modulation amplitude –5.2 dBm Minimum extinction ratio 3.5 dB Maximum optical return loss tolerance –12 dB Maximum transmitter reflectance –12 dB Receiver characteristics Line rate (nominal) 10GBASE-LR 10.
SFP+ specifications Parameter Specifications Minimum side mode suppression ratio 30 dB Minimum launch power in OMA minus transmission and dispersion penalty (TDP) –2.1 dBm Minimum optical modulation amplitude –1.7 dBm Maximum average launch power of OFF transmitter –30 dBm Minimum extinction ratio 3.0 dB Maximum RIN12OMA –128 dB/Hz Maximum optical return loss tolerance –21 dB Receiver characteristics Average receive power for BER 10-12 – 15.8 dBm to –1.
SFP+ Parameter Specifications Line rate (64B/66B code) 10.3125 Gbps ± 100 parts per million (ppm) Center wavelength range 840 to 860 nanometers (nm), nominal 850 nm Distance Using 62.5 µm MMF optic cable: • 160 MHz-km fiber: 2 to 26 m • 200 MHz-km fiber: 2 to 33 m Using 50 µm MMF optic cable: • 400 MHz-km fiber: 2 to 66 m • 500 MHz-km fiber: 2 to 82 m • 2000 MHz-km fiber: 2 to 300 m • 4700 MHz-km fiber (OM4): 2 to 400 m Link optical power budget 3.
SFP+ specifications Table 20: IEEE 802.3ae 10GBase–SR/SW SFP+ (0 °C to +85 °C) transceiver specifications Parameter Specifications Data rate 10 Gigabits per second (Gbps) Line rate (64B/66B code) 10.3125 Gbps ± 100 parts per million (ppm) Center wavelength range 840 to 860 nanometers (nm), nominal 850 nm Distance Using 62.
SFP+ Warning: Risk of BER increase For proper SFP+ transceiver operation, ensure that at least 11 dB of attenuation is present between the transmit and receive ports. The reach for this SFP+ transceiver is up to 70 km* at a wavelength of 1550 nm. Table 21: 10GBASE-ZR/ZW SFP+ specifications Parameter Specifications Line rate (nominal) 10GBASE-ZR 10.3125 Gbps ±100 ppm (10 GbE) Distance Up to 70 km * Link optical power budget 24 dB Dispersion power penalty 3.0 dB at 70 km (G.
SFP+ specifications Table 22: 10GBASE-CX cables Cable length Part number 3 meter AA1403019-E6 5 meter AA1403020-E6 7 meter AA1403022-E6 10 meter AA1403018-E6 10GBASE CWDM DDI SFP+ (40 km) specifications The following table lists the part numbers of the 10GBASE CWDM DDI SFP+ (40 km) with corresponding wavelengths.
SFP+ Parameter Specifications Wavelength (requirement) 1450 nm to 1620 nm Receiver sensitivity (unstressed), OMA –14.1 dBm, P_OMA IEEE 10GBASE-ER Stressed Rx Sensitivity –11.3 dBm, P_OMA Receiver overload –1 dBm, P_avg Receiver reflectance –26 dB Receiver damage threshold +4 dBm 10GBASE-LRM SFP+ specifications The 10GBASE-LRM SFP+ transceiver provides 10 GbE service at a wavelength of 1310 nm. This SFP+ transceiver supports a reach of up to 220 m on 62.
SFP+ specifications Parameter Specifications Optical return loss tolerance (minimum) –20 dB Receiver characteristics Receiver damage threshold 1.5 dBm Receiver reflectance (maximum) –12 dB For more information about the conditions used for the stressed receiver tests, and other information, see the IEEE 802.3–2012 standard. The following table (from IEEE 802.3–2012) describes the maximum channel insertion loss. The channel insertion loss includes both attenuation and connector loss (1.
SFP+ 10GBASE CWDM DDI SFP+ (70 km) specifications The following table lists the part numbers for the 10GBASE CWDM DDI SFP+ (70 km) transceivers with corresponding wavelengths. The reach for this SFP+ transceiver is up to 70 km* at a wavelength of 1551 nm.
SFP+ specifications Parameter Specifications Rx sensitivity: Min Max Units back-to-back — –23 dBm with 70 km fiber — –21 dBm –19.3 dBm with 70 km fiber, OMA — Receiver overload –7 dBm, P_avg Receiver reflectance –27 dB Receiver damage threshold +5 dBm, P_avg 10GBASE-BX SFP+ specifications The 10GBASE-BX SFP+ provides 10 Gigabit Ethernet (GbE) service with single mode bidirectional transceivers.
SFP+ Parameter Specifications Average receive power –14.4 to +0.5 dBm Maximum receiver sensitivity in OMA –12.6 dBm Maximum receiver reflectance –12 dB Stressed receiver sensitivity in OMA –10.3 dBm January 2018 Installing Transceivers and Optical Components on VOSS Comments on this document? infodev@avaya.
Chapter 8: QSFP+ This chapter provides installation procedures and specifications for 40 Gigabit Ethernet Quad Small Form Factor Pluggable plus (QSFP+) transceiver modules. QSFP+ transceivers This section describes how to select, install, and remove Quad (4-channel) Small Form Factor Pluggable plus (QSFP+) transceiver modules. Use a QSFP+ transceiver to connect a device motherboard to fiber optic or direct attach cables. QSFP+ transceivers support 40 gigabit per second (Gbps) connections.
QSFP+ basic displays the corresponding vendor names instead of leaving the vendor name blank as in the releases prior to VOSS 4.2.1. • Avaya recommends the use of Avaya branded SFP and SFP+ transceivers as they have been through extensive qualification and testing. Avaya will not be responsible for issues related to non-Avaya branded SFP and SFP+ transceivers. Selecting a QSFP+ Use a QSFP+ transceiver for 40 Gigabit per second (Gbps) Ethernet connections over optical fiber.
QSFP+ transceivers Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber optic cables connect to a light source. Electrostatic alert: Risk of equipment damage ESD can damage electronic circuits. Do not touch electronic hardware unless you wear a grounding wrist strap or other static-dissipating device. Warning: Risk of equipment damage Only trained personnel can install this product.
QSFP+ Removing a QSFP+ transceiver Remove a QSFP+ transceiver to replace it or to commission it elsewhere. Before you begin Danger: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber optic cables connect to a light source.
QSFP+ transceiver specifications QSFP+ transceiver labels A label can be located on either the top or bottom of the typical Avaya QSFP+ transceiver. The following figure shows an example label. Avaya uses alternate labels, depending on the size of the device and space available for label information. Figure 7: 40GBASE–SR4 QSFP+ transceiver label example The following table identifies the numbered items in the preceding figure. Table 29: Figure notes for a 40GBASE–SR4 QSFP+ transceiver label 1.
QSFP+ Table 30: General QSFP+ specifications Parameter Specification Dimensions (H x W x D) 8.5 x 18.35 x 72.4 mm (0.33 x 0.72 x 2.85 in.), unless otherwise stated. Note: The length of the pull tab latch varies depending on the vendor and the body, with a length of 125 to 132 mm (4.92 to 5.20 in.).
QSFP+ transceiver specifications Parameter Specification Distance Up to: • 328 feet (100 meters) – with OM3 fiber cable. • 492 feet (150 meters) – with OM4 fiber cable. Transmitter characteristics Signaling rate, each lane 10.3125 Gbps RMS spectral width 0.65 nanometers maximum Average launch power, each lane Optical modulation amplitude (OMA), each lane Min Max Units –8.0 –1.0 dBm Min Max Units –5.6 3 dBm Maximum transmitter and dispersion penalty (TDP), each lane 3.
QSFP+ Table 32: 40GBASE-SR4 4x10GBASE-SR extended reach specifications Parameter Specification Line rate 10.3125 Gbps Center wavelength range 840 to 860 nanometers Distance Up to: • up to 984 feet (300 meters) – with OM3 fiber cable. • up to 1312 feet (400 meters) – with OM4 fiber cable. Transmitter characteristics Signaling rate, each lane 10.3125 Gbps RMS spectral width 0.40 nanometers maximum Average launch power, each lane Optical modulation amplitude (OMA), each lane Min Max Units –7.
QSFP+ transceiver specifications For more information about the 40GBASE-LR4 transceiver, including test and measurement information, see the IEEE 802.3–2012 standard. Table 33: IEEE 802.3–2012 40GBASE-LR4 transceiver specifications Parameter Specification Distance Up to 10 kilometers Transmitter characteristics Line rate 10 Gbps Signaling rate, each lane 10GBase 10.3125 Gbps Data rate, total 40GBase 41.25 Gbps Lane wavelength ranges 1264.5 nanometers to 1277.5 nanometers 1284.
QSFP+ Parameter Specification Maximum receiver sensitivity in OMA, each lane at 10.3125 Gbps. –11.5 dBm Maximum receiver reflectance –26 dBm Stressed receiver sensitivity, each lane at 10.3125 Gbps. –9.6 dBm Receive input optical power (damage threshold per lane) 3.3 dBm 40GBASE-LM4 QSFP+ specifications This transceiver operates up to 80 meters on 50 µm MMF cable plant and is compliant with channel insertion loss specified in IEEE standard 802.
QSFP+ transceiver specifications Parameter Specification Maximum insertion loss, including connectors 2.6 dB (OM3) or 2.9 dB (OM4) Minimum optical return loss 20 dB Maximum link distance 80 m Receiver characteristics Maximum average receive power, each lane 4.3 dBm Maximum input optical power Tolerates direct Tx to Rx connection Stressed receiver sensitivity –5.
QSFP+ Maximum average optical power of OFF transmitter, each lane –30 dBm Launch power in OMA minus TDP, each lane, (min.) –0.5 dBm Minimum extinction ratio at 10.3125 Gbps 5.5 dB RIN20OMA (maximum) –128 dB/Hz Maximum optical return loss tolerance 20 dB Receiver characteristics Line rate 10 Gbps Signaling rate, each lane 10GBASE 10.3125 Gbps Damage threshold per lane (min.) 3.8 dBm Lane wavelength ranges 1264.5 nanometers to 1277.5 nanometers 1284.5 nanometers to 1297.5 nanometers 1304.
QSFP+ transceiver specifications Interoperation 40GBASE-ER4 and 40GBASE-LR4 QSFP+ transceivers can interoperate with a properlyengineered link. It requires the cabling (channel) characteristics for 40GBASE-LR4 to be met, with the exception of the maximum and minimum channel insertion loss values, as shown in the following table, for the two link directions separately. Direction Min. loss Max. loss Unit 40GBASE-LR4 transmitter to 40GBASEER4 receiver 7.5 14.
Chapter 9: End of sale transceivers and cables This section contains a complete list of transceivers, BOCs, and DACs that have reached End of Sale. This list applies to all products. For more information about EOS transceivers and recommended replacements for your product or to determine existing availability for these transceivers, see Locating end of sale notices on page 68.
End of sale XFP transceivers Model Part number Date EOS Replacement 1000BASE-XD CWDM AA1419025-E5 to AA1419032-E5 June 30, 2012 1000BASE-ZX CWDM AA1419033-E5 to AA1419040-E5 June 30, 2012 — 1000BASE-XD DDI 1330 nm AA1419050-E6 September 30, 2014 — 1000BASE-XD DDI 1550 nm AA1419051-E6 September 30, 2014 AA1419057-E6 1000BASE-ZX DDI 1550 nm AA1419052-E6 September 30, 2014 AA1419065-E6 1000BASE- XD DDI 40 km AA1419053-E6 to AA1419060-E6 December 14, 2016 — 1000BASE-ZX DDI CWDM 70 km
End of sale transceivers and cables Model Part number Date EOS Replacement QSFP+ to QSFP+ DAC CABLE AA1403028-E6 June 2015 AA1404028-E6 AA1404030-E6 August 2016 — 10 meter (ACTIVE COPPER) QSFP+ to QSFP+ DAC CABLE 2 meter (PASSIVE COPPER) January 2018 Installing Transceivers and Optical Components on VOSS Comments on this document? infodev@avaya.
Chapter 10: Translations of safety messages Class A electromagnetic interference warning statement Warning: Risk of electromagnetic interference This device is a Class A product. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users are required to take appropriate measures necessary to correct the interference at their own expense. Warning: AVERTISSEMENT Le périphérique est un produit de Classe A.
Translations of safety messages Este dispositivo é um produto Classe A. Operar este equipamento em uma área residencial provavelmente causará interferência prejudicial; neste caso, espera-se que os usuários tomem as medidas necessárias para corrigir a interferência por sua própria conta. Warning: AVVISO Questo dispositivo è un prodotto di Classe A.
Laser eye safety danger statement Electrostatic alert: AVVISO ELETTROSTATICO Le scariche elettrostatiche (ESD) possono danneggiare i circuiti elettronici. Non toccare i componenti elettronici senza aver prima indossato un braccialetto antistatico o un altro dispositivo in grado di dissipare l'energia statica. Laser eye safety danger statement Danger: Risk of eye injury by laser Fiber optic equipment can emit laser or infrared light that can injure your eyes.
Translations of safety messages O laser pode causar ferimentos no olho O equipamento de fibra ótica pode emitir laser ou luz infravermelha que pode causar danos a sua vista. Nunca olhe para dentro da fibra ótica ou da porta do conector. Tenha sempre em mente que os cabos de fibra ótica estão ligados a uma fonte de luz. Danger: PERICOLO Rischio di ustioni agli occhi dovute al laser Le apparecchiature con fibre ottiche possono emettere raggi laser o infrarossi in grado di provocare ferite agli occhi.
Connector cleaning safety danger statement Danger: PERIGO Risco de ferimento nos olhos Ao inspecionar um conector, verifique se as fontes luminosas estão desligadas. A fonte luminosa usada nos cabos de fibra ótica pode causar danos a seus olhos. Danger: PERICOLO Rischio di lesioni agli occhi Quando si esamina un connettore, assicurarsi che le sorgenti di luce siano spente. La sorgente di luce utilizzata nei cavi a fibre ottiche potrebbero danneggiare gli occhi.
Translations of safety messages arbeiten. Zum Schutz vor Augenirritationen tragen Sie eine Schutzbrille, wenn Sie mit Isopropanol arbeiten. Danger: PELIGRO Riesgo de lesiones Cuando inspeccione un conector, controle que las fuentes de luz estén apagadas. La fuente de luz que utilizan los cables de fibra óptica puede ocasionar daños en la vista. Cuando trabaje con el pulverizador de aire envasado, utilice gafas de seguridad para evitar el ingreso de residuos en los ojos.
Optical fiber connector damage warning statement Warning: AVERTISSEMENT Risques d'endommagement de l'équipement N'exercez pas de pression sur les câbles de fibres optiques. Ne placez pas de câbles de fibres optiques dans la même caisse ou dans le même fourreau que des câbles électriques lourds car leur poids risquerait de les endommager. Warning: WARNUNG Risiko von Geräteschäden Das Glasfaserkabel darf nicht zerdrückt werden.
Translations of safety messages To prevent further contamination, clean fiber optic equipment only when you see evidence of contamination. To prevent contamination, cover the optical ports of all active devices with a dust cap or optical connector. To avoid the transfer of oil or other contaminants from your fingers to the end face of the ferrule, handle connectors with care.
SFP damage warning statement Warning: AVISO Risco de danos ao equipamento Para evitar contaminação futura, limpe o equipamento ótico apenas quando houver evidência de contaminação. Para evitar a contaminação, verifique se as portas óticas de todos os dispositivos ativos estão cobertas com uma proteção contra pó ou conector ótico. Para evitar a transferência de óleo ou outro agente contaminador de seus dedos para a extremidade final da ponteira, manuseie os conectores com cuidado.
Translations of safety messages Die SFPs sind so konstruiert, dass ein falsches Einsetzen verhindert wird. Lässt sich ein SFP auch auf Druck hin nicht einsetzen, versuchen Sie nicht, es gewaltsam einzusetzen, sondern drehen Sie es um, und setzen Sie es erneut ein. Warning: ADVERTENCIA Riesgo de daños en los equipos Los módulos SFP cuentan con cuñas que no permiten insertarlos de forma incorrecta. Si el módulo SFP opone resistencia a la presión, no lo fuerce; gírelo e insértelo nuevamente.
Chapter 11: Resources Support Go to the Avaya Support website at http://support.avaya.com for the most up-to-date documentation, product notices, and knowledge articles. You can also search for release notes, downloads, and resolutions to issues. Use the online service request system to create a service request. Chat with live agents to get answers to questions, or request an agent to connect you to a support team if an issue requires additional expertise.
Resources About this task Videos are available on the Avaya Support website, listed under the video document type, and on the Avaya-run channel on YouTube. Procedure • To find videos on the Avaya Support website, go to http://support.avaya.com and perform one of the following actions: - In Search, type Avaya Mentor Videos to see a list of the available videos. - In Search, type the product name. On the Search Results page, select Video in the Content Type column on the left.
Subscribing to e-notifications 5. Select any of the following to narrow your search: • Whole Words Only • Case-Sensitive • Include Bookmarks • Include Comments 6. Click Search. The search results show the number of documents and instances found. You can sort the search results by Relevance Ranking, Date Modified, Filename, or Location. The default is Relevance Ranking.
Resources 6. Click OK. 7. In the PRODUCT NOTIFICATIONS area, click Add More Products. 8. Scroll through the list, and then select the product name. 9. Select a release version. 10. Select the check box next to the required documentation types. January 2018 Installing Transceivers and Optical Components on VOSS Comments on this document? infodev@avaya.
Subscribing to e-notifications 11. Click Submit. January 2018 Installing Transceivers and Optical Components on VOSS Comments on this document? infodev@avaya.
Glossary attenuation The decrease in signal strength in an optical fiber caused by absorption and scattering. Avaya command line interface (ACLI) A textual user interface. When you use ACLI, you respond to a prompt by typing a command. After you enter the command, you receive a system response. bit error rate (BER) The ratio of the number of bit errors to the total number of bits transmitted in a specific time interval.
media media A substance that transmits data between ports; usually fiber optic cables or category 5 unshielded twisted pair (UTP) copper wires. metropolitan area network (MAN) A broadband network that covers an area larger than a Local Area Network. multimode fiber (MMF) A fiber with a core diameter larger than the wavelength of light transmitted that you can use to propagate many modes of light. Commonly used with LED sources for low speed and short distance lengths.
