Quick Install Guide

ManualsBrandsExtreme Networks ManualsComputers & AccessoriesHigh-performance 10/40 Gigabit Ethernet Switch

Confirm that you have the following tools and cables:

• Phillips #2 screwdriver

• RJ-45 console port cable

• ESD cable

Virtual Services Platform

7200 Series

Quick Install Guide

1. Virtual Services Platform (VSP) 7200 Series switch

2. Rack-mounting hardware that includes:

a. Rack-mount brackets

b. Screws to attach brackets to the switch

c. Screws to attach the switch to the equipment rack

3. AC power cord or DC power supply wiring assembly

(Note: A power cord is not included with the “A” variants of

the switch.)

4. Documentation that includes this poster, regulatory

information, how to locate software, and how to locate

Release Notes.

This poster provides information and instructions to install

and commission a factory-supplied Extreme Networks

Virtual Services Platform 7200 switch. You can download all

documents referenced in this guide at

http://www.extremenetworks.com/support/documentation/.

Note: Observe ESD precautions when unpacking.

Optionally order a redundant PSU to provide redundancy and

load sharing. Make sure you order the correct power supplies

and fan trays so the air flow directions match (either

front-to-back or back-to-front).

VSP 7200 AC power specifications:

VSP 7200

model

Primary

PSU

Redundant PSU

(to be ordered if required)

VSP 7254XSQ - fiber switch

Model EC7200x1B-E6

All Ports Enabled

Ships with one back-to-front

AC PSU and back-to-front fan

modules

Model EC7200x1F-E6

All Ports Enabled

Ships with one front-to-back

AC PSU and front-to-back fan

modules

Model EC7200x3B-E6

24x10G+4x40G Ports Enabled

Ships with one back-to-front

AC PSU and back-to-front fan

modules

Model EC7200x3F-E6

24x10G+4x40G Ports Enabled

Ships with one front-to-back

AC PSU and front-to-back fan

modules

460W AC

power supply

Replacement

order code:

EC7205?1B-E6

(back-to-front),

EC7205?1F-E6

(front-to-back)

460W AC power supply

Order code:

EC7205?1B-E6

(back-to-front),

EC7205?1F-E6

(front-to-back)

• “A”: No power cord included.

• “B”: Includes European

“Schuko” power cord

common in Austria,

Belgium, Finland, France,

Germany, The Netherlands,

Norway, and Sweden.

• “C”: Includes power cord

commonly used in the

United Kingdom and Ireland.

• “D”: Includes power cord

commonly used in Japan.

• “E”: Includes North

American power cord.

• “F”: Includes Australian

power cord.

VSP 7254XTQ - copper switch

Model EC7200x2B-E6

All Ports Enabled

Ships with one back-to-front

AC PSU and back-to-front fan

modules

Model EC7200x2F-E6

All Ports Enabled

Ships with one front-to-back

AC PSU and front-to-back fan

modules

Model EC7200x4B-E6

24x10G+4x40G Ports Enabled

Ships with one back-to-front

AC PSU and back-to-front fan

modules

Model EC7200x4F-E6

24x10G+4x40G Ports Enabled

Ships with one front-to-back

AC PSU and front-to-back fan

modules

800W AC

power supply

Replacement

order code:

EC7205?0B-E6

(back-to-front),

EC7205?0F-E6

(front-to-back)

800W AC power supply

Order code:

EC7205?0B-E6

(back-to-front),

EC7205?0F-E6

(front-to-back)

Refer to the note above for

country code information.

The VSP 7200 supports two field-replaceable power supplies. One

power supply ships with the unit and you can optionally install a

second power supply for redundancy. If you install a second power

supply, the load is shared equally and neither one acts as a primary

power supply.

Use this procedure to install either the primary or redundant

power supply.

Notes:

• Extreme Networks does not support installing a combination of

AC-input and DC-input power supplies in the same chassis.

• There are two power supply slots (PSU1 on the left and PSU2 on

the right). If you only have one power supply, you can install it in

either PSU1 or PSU2.

• The switch ships with filler panels covering the power supply

slots. If you’re not installing a second power supply, you must

leave one of the filler panels in place for proper cooling.

• You can hot swap power supplies while the switch is

operational. One power supply is required for continued switch

operation.

Remove the power supply cover by pushing the tab on the

spring latch to the left and pulling on the extraction handle.

(Save the filler panel for possible future use.)

Insert the power supply into the slot.

Verify that the power supply is fully seated in the slot (AC PSU

shown). The spring latch should engage and move back to its

original position.

Notes:

• The chassis design prevents an incorrect installation of a

power supply. If you insert a power supply upside down, it will

not fully insert.

• The spring latch design ensures that you remove the power

cord before removing a power supply from the chassis. If you

don’t remove the cord, you cannot move the latch to the left

to release the hooks from the chassis.

4. After you install a power supply, proceed with connecting either

the AC power cord or the DC power supply wiring assembly.

5. Check the LED on the power supply. If it is off, the power

supply is not operating. If it is green, the power supply is

operating normally.

The VSP 7200 comes with three 12-V fan trays for either

front-to-back or back-to-front air flow switch cooling. Make sure

you order the correct power supplies and fan trays so the air

flow directions match (either front-to-back or back-to-front).

Refer to the following part numbers to ensure that you install

the correct fan trays in your switch. Both the VSP 7254XSQ

(fiber switch) and the VSP 7254XTQ (copper switch) use the

same fan tray models:

• EC7200BTF-E6 — 12 V BACK2FRONT SPARE FAN TRAYS

(INC 3 FAN TRAY KITS)

• EC7200FTB-E6 — 12 V FRONT2BACK SPARE FAN TRAYS

(INC 3 FAN TRAY KITS)

Important:

All three fans must be installed at all times to ensure proper

ventilation. If a fan fails, leave it in place until you can replace it.

Leaving a fan bay unpopulated impairs the ability of the

remaining fans to cool the chassis.

1. Insert the fan trays into the chassis.

There are two ways to install an VSP 7200 switch in an

equipment rack. Refer to one of the following sections:

• Mount the switch using the supplied bracket.

• Mount the switch using the optional slide rack mount kit.

Note: For more information, see Installing the Installing the

Virtual Services Platform 7200 Series, NN47228-302.

VSP 7200 DC power specifications:

VSP 7200

model

Primary

PSU

Redundant PSU

(to be ordered if required)

VSP 7254XSQ -

fiber switch

Model EC720001F-E6

ships with one

front-to-back DC PSU.

800W DC power

supply

Replacement

order code:

EC8005001-E6

(front-to-back)

800W DC power supply

Order code:

EC8005001-E6 (front-to-back)

VSP 7254XTQ -

copper switch

Model EC720002F-E6

ships with one

front-to-back DC PSU.

800W DC power

supply

Replacement

order code:

EC8005001-E6

(front-to-back)

800W DC power supply

Order code:

EC8005001-E6 (front-to-back)

2. Verify that each fan tray is fully seated in the chassis. The

spring latch should engage and return to its original position.

3. Check the Fan LED on the front of the chassis. Solid green

indicates that all fan trays are operating normally. Blinking

amber indicates that a fan tray failed.

4. If a fan tray fails, enter the following command to determine

which one failed.

show sys-info fan

This command shows the status of each fan tray: up, down, or

Not Present when a fan is removed.

5. Remove the fan tray that failed by pushing the tab on the

spring latch to the left and pulling on the fan’s extraction

handle. You can hot swap fan trays while the switch

is operational.

6. Enter the following command to check the temperature

sensors inside the switch.

show sys-info temperature

Before you start

Unpack the equipment and

verify package content

Verify power supply unit (PSU)

specifications

Install power supply unit

Install fan trays

Mount the VSP 7200 switch

Link/Act

VSP 7254XTQ

PWR

Status

RPS

Fan

USB

Link/Act

Summary of content (2 pages)

PAGE 1
3 Verify power supply unit (PSU) specifications Optionally order a redundant PSU to provide redundancy and load sharing. Make sure you order the correct power supplies and fan trays so the air flow directions match (either front-to-back or back-to-front). VSP 7200 AC power specifications: Virtual Services Platform 7200 Series Quick Install Guide This poster provides information and instructions to install and commission a factory-supplied Extreme Networks Virtual Services Platform 7200 switch.
PAGE 2
Prepare the rack • Ensure that there is enough rack space to accommodate a 1RU switch (4.45 cm). • The rack is bolted to the floor and braced if necessary. • The rack is grounded to the same grounding electrode used by the power service in the area. The ground path must be permanent and must not exceed 1 Ohm of resistance from the rack to the grounding electrode. Mount the switch using the supplied bracket Caution: It is recommended using the mounting brackets with a shelf.