AP-7622 Access Point Installation Guide Published October 2017 9035128-03 9035128-03 Published October 2017 9035128-03
Copyright © 2017 Extreme Networks, Inc. All Rights Reserved. Legal Notices Extreme Networks, Inc. reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice.
Contents Introduction ...............................................................................................................3 Warnings ...............................................................................................................................................................................3 Site Preparation .................................................................................................................................................................
Contents Power Supply ..............................................................................................................................................................................24 Radio Frequency Interference Requirements—FCC ........................................................................................ 25 Radio Transmitters (Part 15) ................................................................................................................................................
1 Introduction The Access Point’s unique WiNG 5 software enables the Access Point to function as either a Standalone Access Point, an Adaptive Access Point or a Virtual Controller. If new to Access Point technology, refer to the WiNG Access Point System Reference Guide to familiarize yourself with the feature set supported by the WiNG operating system. This document is written for the qualified network device installer.
Introduction • One 2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio The GE1/POE accepts 802.3at or 802.3af compliant power from an external source. NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended for Gigabit operation. AP-7622 Antennas An AP-7622 internal antenna Access Point supports the following: 2.4 GHz Gain (dBi) 5 GHz Gain (dBi) 3.64dBi 5.
2 Hardware Installation Installation Instructions An AP-7622 Access Point mounts either on a wall or on a suspended ceiling T-Bar. To prepare for the installation: To prepare for the installation: 1 Match the part number on the purchase order with the part numbers in the packing list and on the case of the Access Point. 2 Verify the contents of the box include the intended AP-7622 Access Point, and the included hardware matches the package contents. Part Number Description AP-7622-68B30-US 802.
Hardware Installation Access Point Placement For optimal performance, install the Access Point away from transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls or floors block transmission. Install the Access Point in an open area or add Access Points as needed to improve coverage. Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough.
Hardware Installation the AP is operating using injector supplied power, the AP will not automatically reboot if an AC adapter is connected. The Access Point continues to operate with power supplied from the AC adapter without change to the Access Point operating configuration. If using AC adapter supplied power and a change to the AP’s operating configuration is warranted, the Access Point needs to be manually rebooted by the customer.
Hardware Installation • The Power Injector isn’t a repeater, and does not amplify the Ethernet signal. For optimal performance, ensure the Power Injector is placed as close as possible to the data port. CAUTION To avoid problematic performance and restarts, disable POE from a wired switch port connected to an Access Point if mid-span power sourcing equipment (PSE) is used between the two, regardless of the manufacturer of the switch.
Hardware Installation 1 Measure and mark two holes 89mm (3.5") apart at the intended deployment orientation of the unit. NOTE When pre-drilling a hole the recommended hole size is 4mm (0.16in.). 2 Drill pilot holes at the locations marked on the wall.. 3 Cable the Access Point using the Power Injector solution, approved AP-7622 power supply or a POE enabled switch.
Hardware Installation 4 Verify the Access Point is receiving power by observing the LEDs are lit or flashing. 5 Secure the AP-7622 to the wall using oval head screws. 6 The Access Point is ready to configure. Ceiling Mount Instructions A ceiling mount requires holding the AP-7622 up against a T-Bar of a suspended ceiling grid and twisting the unit on to the T-Bar. If deploying the AP-7622 on a sculpted ceiling TBar, the Access Point mounting kit (Part No. KT-135628-01) can be used as well.
Hardware Installation 7 Rotate the Access Point 45 degrees counter-clockwise. The clips click as they fasten to the T-Bar. 8 The Access Point is ready to configure. AP-7622 Beam Clip When needed, an AP-7622 can also be ceiling mounted using a beam clip. If utilizing a beam clip, attach the beam clip to the AP-7622’s integrated mounting bracket. Then connect the Access Point to the ceiling beam.
Hardware Installation LED Indicators The AP-7622’s three LED activity indicators are located on the front of the housing and are visible through the enclosure. The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz 802.11ac (amber) radio, 2.4 GHz 802.11n (green) radio and Bluetooth activity (blue) radio. NOTE LED behavior for the AP-7622 are identical in both WLAN and client bridge modes.
Hardware Installation Task Green Amber Blue Sensor with Server Connected On 1 second, Off 1 second On 1 second, Off 1 second N/A Synced with Amber LED Synced with Green LED On 1 second, Off 5 seconds On 1 second, Off 5 seconds Synced with Amber LED Synced with Green LED Locate AP Mode Irregular Blink Rate, Green/Amber/Blue Irregular Blink Rate, Green/Amber/Blue Irregular Blink Rate, Green/Amber/Blue Bluetooth Radio Enabled N/A N/A Solid Blue Bluetooth Radio Disabled N/A N/A Off Se
Hardware Installation AP-7622 Access Point Installation Guide 14
3 Basic Configuration Once the Access Point is installed and powered on, complete the following WiNG Assist configuration steps to get the Access Point up and running with minimal administrative intervention. Startup Assist updates existing settings. To delete or revise existing Startup Assist settings, either rerun Startup Assist or navigate to where those parameters appear in the user interface and update them accordingly.
Basic Configuration If logging in using a factory default configuration, Startup Assist automatically displays. If Startup Assist does not automatically display, it can be invoked at any time from the upper-left of the Basic Configuration screen. NOTE Startup Assist automatically sets the radio transmit power and enables Auto Channel selection. The Access Point's name is automatically assigned based on the Access Point type and the last three octets of the device's hard coded MAC address.
Basic Configuration regulatory restrictions concerning electromagnetic emissions and the maximum RF signal strength that can be transmitted. NOTE Country Name can not be changed when deployed in the United States or Canada. • Timezone - Use the drop-down menu to specify the geographic timezone where the AP-7622 is deployed. Different geographic time zones have daylight savings clock adjustments, so specifying the timezone correctly is important to account for geographic time changes.
Basic Configuration AP-7622 Access Point Installation Guide 18
4 AP-7622 Access Point Specifications Electrical Characteristics An AP-7622 has the following electrical characteristics: Operating Current & 12VDC, 1A, 2.5mm barrel connector, center positive Voltage Power over Ethernet 48VDC, .25A, PoE Physical Characteristics An AP-7622 Access Point has the following physical characteristics: Dimensions 7.1 in. L x 6.5 in. W x 1.6 in. H 180 mm L x 165 mm W x 41 mm H Weight 0.85 lbs/0.
AP-7622 Access Point Specifications AP-7622 Access Point Installation Guide 20
5 Regulatory Information Regulatory Information This guide applies to the following Model Number AP-7622. Extreme Networks devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following Website: www.extremenetworks.com/support Any changes or modifications to Extreme Networks equipment, not expressly approved by Extreme Networks could void the user's authority to operate the equipment.
Regulatory Information Declaration of Conformity in Languages of the European Community Hereby, Extreme Networks, Inc. declares that the radio equipment type Wireless LAN Access Point is in compliance with Directive 1999/5/EC. The full text of the EU declaration of conformity is available at the following Internet address: http://www.extremenetworks.com/ Country Selection Select only the country in which the device will be used. Any other selection will make the operation of this device illegal.
Regulatory Information Health and Safety Recommendations Ergonomic Recommendations CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.
Regulatory Information • If you have any reason to suspect that interference is taking place, turn OFF your device. Other Medical Devices Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device. RF Exposure Guidelines Safety Information Reducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied.
Regulatory Information recommended ambient temperature greater than 50 degrees C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous. The product is to be connected to PoE networks without routing to the outside plant. Radio Frequency Interference Requirements—FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
Regulatory Information This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Regulatory Information Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz. Bluetooth® Wireless Technology for use throughout the EEA has the following restrictions: • Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 2.4835 GHz. Statement of Compliance Extreme Networks hereby declares that this radio equipment is in compliance with Directive 2011/65/EU and 1999/5/EC or 2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017).
Regulatory Information Australia Use of 5GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65GHz. Brazil Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em Sistemas devidamente autorizados. Chile Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas.
Regulatory Information China 通过访问以下网址可下载当地语言支持的产品说明书www.extremenetworks.com/support. Eurasian Customs Union Hong Kong In accordance with HKTA1039, the band 5.15GHz - 5.35GHz is for indoor operation only. Mexico La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Regulatory Information Thailand เครื่องโทรคมนาคมและอุปกรณนี้ มีความสอดคลองตามขอกําหนดของ กทช. Taiwan 台灣 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及乾擾合法通信；經發現有干擾現象時，應立即 停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線電通信。 低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 使用此產品時應避免影響附近雷達系統之操作。 無線基地台（專業安裝） • “本公司於說明書中提供所有必要資訊以指導使用者/安裝者正確的安裝及操作”警 語。並於該中文使用說明書及器材上標示。 • “本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者 ”警語。 電磁波曝露量MPE標準值 1mW/cm² ; 送測產品實測值為 : 0.
Regulatory Information When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately. It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment.
