Quick Reference Guide

ManualsBrandsExtreme Networks ManualsComputers & Accessories802.11ac Wave 2 Access Point

Installing the ExtremeWiNG 802.11 a/ac+b/g/n

Indoor AP7632 Access Point

Overview of the AP7632

The AP7632 is an 802.11ac Wave 2 Access Point featuring dual 2x2:2 radios.

The all-metal design of the AP supports high operating temperatures, external

antennas, and flexible mounting options for wall mount, ceiling mount, beam

or T-bar. The AP can be powered by 802.3af or by using a 12VDC wall brick.

The AP7632 model has the following features:

• Radios: 2 radios (2.4GHz and 5GHz); 1 IoT Radio (2.4 GHz)

•Console Port: RJ45

• One RJ45, 10/100/1000 Ethernet Port (LAN1) with PoE

•LEDs: 4 (see Figure 2)

•One Reset button

• Power: PoE 802.3af; 12VDC power in connector (see Table 1)

• Antennas:

–Three external antennas (two dual band antennas and one IoT

antenna)

– Three RSPMA mount style antenna connectors

• External USB 2.0 port with features to support a locking module

•Safety Hangar provision

• Temperature:

– -20 to +55°C ambient temperature anywhere

– -20 to +65°C ambient temperature near sea level

• Enclosure: All metal - no plastic

In Figure 1, the top image indicates the top view of AP7632 and the bottom

one indicates the side view of AP7632.

Figure 1 Top and Side View of AP7632

Table 1 shows ways to power the AP7632.

Table 1 Powering the AP7632

Note: The AP7632 requires a minimum base firmware of WiNG 5.9.1.

2.4G/5G Radio 1 and 2

GE1/PoE

Console RJ45 connector

Reset button

Optional 12V DC power supply connector

BLE Radio

Kensington Lock Slot

2.4G/5G Radio 1 and 2

USB Port

Power Source

Description

Power over

Ethernet

(PoE)

Power is provided through the RJ45 Ethernet port (GE1 port)

to the right of the 12V DC port. This is the preferred method

of powering the AP on ceiling and high wall installations.

Figure 2 shows the LEDs on the front of the AP7632.

Figure 2 LEDs on AP Front Face

Green LEDs indicate 2G Wi-Fi Radio, Amber LEDs indicate 5.2G Wi-Fi Radio,

and Blue LED indicates the IoT Radio. The Status LED is Green only during

boot up and remains off during normal use.

For detailed installation information about the AP7632, see the Extreme

Networks WiNG AP7632 Installation Guide.

Verifying the AP7632 Box Contents

Verify the contents of the box and ensure that the following items are

available:

Mounting and Connecting the AP

Use these instructions as guidelines for mounting and connecting the AP7632

easily and safely.

The AP7632 comes with a Mounting Bracket (ordering part #37201) that can

be used to mount the AP on a flat surface. You can also purchase an optional

flat metal indoor bracket (ordering part #37210) for easy installation.

You also have an option to purchase the optional adapter if you want to mount

the AP on a suspended or drop ceiling.

For more information about installing the optional bracket and the adaptor,

see the Extreme Networks WiNG AP7632 Installation Guide.

For installation videos of the AP, see www.extremenetworks.com/support/

Mounting the AP on a Dry or Wood Wall/Solid Flat

Ceiling

To install the AP on a dry wall or flat surface:

Option 1: Using the Main Bracket

1 Use the main bracket as a template and mark the hole centers on the wall.

2 Drill two holes 81mm (3.200”) apart from each other on the wall where you

want to mount the AP.

3 Insert the screws through the bracket and into the holes. Use the screw-in

anchors if needed.

4 Insert the Ethernet cable’s RJ45 connector into the LAN1/GE1 port.

5 Slide the AP onto the bracket’s four feet. Ensure that the AP is secured in

place and tightened.

External 12V

DC power

supply

(optional)

The AP7632 can also be powered by an external DC power

supply plugged into an AC source. Plug the supply’s input

jack into the DC-In port (callout 5 in Figure 1).

IoT Radio

Status

Radio 2, 5GHz

Radio 1, 2.4GHz

Table 2 Contents of the AP7632 Box

Quantity Item

1 AP7632 Quick Reference Guide

1 Mounting Bracket for 802.11ac Indoor AP assembled onto the AP

1 Cloud Quick Start Card

The following hardware is included:

2 Phillips Pan-head wood screws

2 Screw-in anchors

Electrical Hazard: Only qualified personnel should perform

installation procedures.

Note: Remove the main bracket from the AP to use it as a template.

Note: The four feet of the bracket must be horizontal and pointing to

the right. The flat part of the large surface must be touching the wall.

Power Source

Description

Option 2: Mounting the AP directly to the wall using 2 screws

1 Remove the main bracket attached to the back of the AP.

2 Drill two holes 104mm (4.100”) apart from each other on the wall.

3 Insert the screws into the holes and use the screw-in anchors if needed.

4 Insert the Ethernet cable’s RJ45 connector into the GE1 port (Figure 1; side

view). Attach the optional DC adaptor if there is no PoE on the Ethernet

cable.

5 Insert the keyholes of the AP onto the screws and slide it down till it is

firmly held by the screw heads. If the AP is loose, unmount the AP and

decrease the distance between the screw head and the wall. Remount the

AP.

Figure 3 Attaching AP to a Wall using 2 screws

Option 3: Using an optional Flat Metal Indoor Bracket

1 Attach the Flat Metal Indoor bracket to the main bracket. Keep the adaptor

to the center of the bracket, push and rotate it (Figure 4).

2 Hold the AP to the surface to which it needs to be attached and use the

optional adapter’s end holes as a template to mark the attachment holes.

3 Drill two holes on the solid surface (wall or ceiling) where you want to

mount the AP.

4 Connect the LAN/Ethernet cable to the back of the AP.

5 Hold the AP, insert and tighten the 2 screws until you lock it into place.

Figure 4 Attaching the optional Flat Metal Indoor Bracket to

the main bracket

Option 4: Using an optional Wall and Box bracket

Remove the main bracket from the AP. Follow the procedure mentioned in

ExtremeWireless AP7632 Installation Guide to mount the AP on a Wall and

Box bracket.

Mounting the AP to a Bracket on a Junction or Gang

Box

To mount the AP to a Bracket on a Junction or Gang box, use the Wall and Box

Bracket (needs to be purchased separately).

1 Remove the main bracket from the AP.

2 Follow the procedure mentioned in ExtremeWireless AP7632 Installation

Guide to mount the AP on a Wall and Box bracket.

Mounting the AP to a Suspended or Drop Ceiling

1 Attach the T-bar adaptor by pushing down the main bracket’s angled

locking tabs, pulling up on the T-bar adaptor’s locking pin, and

Note: Leave 1/8” gap between the screw head and the wall.

Note: Mounting the AP to a flat ceiling/wall requires the optional Flat

Metal Indoor Bracket (Purchasing Part #37210), which must be

purchased separately.

Note: Mounting the AP to a flat ceiling/wall requires either the Main

Bracket (Option 1), Flat Metal Indoor Bracket (Option 3), or the

optional Wall and Box Bracket (Option 4 - purchasing part #30516),

which must be purchased separately.

Note: The slot and lock cuts in the rear of the AP (visible when the

main plate is removed) are used for mounting the Wall and Box

bracket. The unlock tab on the bracket should be pointed up. In this

position, the AP7632 can be mounted with the antennas facing

upward or downward.

Note: Mounting the AP to a suspended or drop ceiling requires the

optional adapter (Universal Mounting Kit for EWLAN APs; purchasing

part # KT-135628-01), which must be purchased separately.

simultaneously rotating the adaptor onto the Main Bracket until the locking

pin clicks in place.

2 Slide the T-bar holder onto the T-bar and replace the tiles to hold the

adaptor onto the T-bar.

3 Hold the AP and rock it back and forth to ensure that it is securely

mounted.

4 Attach the Ethernet cable’s RJ45 connector to the LAN1/GE1 port.

The optional WS-MBI-DCMTR01 (purchasing part #30518) adaptor can also be

used for T-bar installations without the mounting bracket. For detailed

instructions, refer ExtremeWireless AP7632 Installation Guide.

Connecting a Power Supply to the AP7632

If you need to power the AP7632 with an external 12V DC power supply, you

can plug the power cord into the power connector (callout 5 in Figure 1) on the

back of the AP. There is no wall mount for the 12V DC power supply. When the

device is powered on, the power LED on the front face of the AP is lit. Refer to

the Extreme Networks WiNG AP7632 Installation Guide for

information about optional power supplies.

LAN/Console Connections

The AP7632 has one GE1 (Ethernet) port and a Console port. Refer to Figure 1

for the location of these ports. During administration and maintenance

through the GE1 or Console, the AP must still have a power connection

through either an Ethernet PoE cable or a DC power supply.

Professional Installation Instruction

Installation personal

This product is designed for specific application and needs to be installed by a

qualified personal who has RF and related rule knowledge. The general user

shall not attempt to install or change the setting.

Installation location

The product shall be installed at a location where the radiating antenna can be

kept 36 cm from nearby person in normal operation condition to meet

regulatory RF exposure requirement.

External antenna

Use only the antennas which have been approved by the applicant. The non-

approved antenna(s) may produce unwanted spurious or excessive RF

transmitting power which may lead to the violation of FCC/IC limit and is

prohibited.

Installation procedure

Please refer to user’s manual for the detail.

Instructions d'installation professionnelle

Installation

Ce produit est destine a un usage specifique et doit etre installe par un

personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant.

L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.

Emplacement d'installation

En usage normal, afin de respecter les exigences reglementaires concernant

l'exposition aux radiofrequences, ce produit doit etre installe de facon a

respecter une distance de 36 cm entre l'antenne emettrice et les personnes.

Antenn externe

Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation

d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non

essentiel depassant les niveaux limites definis par FCC/IC, ce qui est interdit.

Procedure d'installation

Consulter le manuel d'utilisation.

Warning: Please carefully select the installation position and make sure that

the final output power does not exceed the limit set force in relevant rules. The

violation of the rule could lead to serious federal penalty.

Warning: Avertissement: Choisir avec soin la position d'installation et

s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La

violation de cette regle peut conduire a de serieuses penalites federales.

Summary of content (2 pages)

PAGE 1
Installing the ExtremeWiNG 802.11 a/ac+b/g/n Indoor AP7632 Access Point Overview of the AP7632 The AP7632 is an 802.11ac Wave 2 Access Point featuring dual 2x2:2 radios. The all-metal design of the AP supports high operating temperatures, external antennas, and flexible mounting options for wall mount, ceiling mount, beam or T-bar. The AP can be powered by 802.3af or by using a 12VDC wall brick.
PAGE 2
Operational Description of Antenna Configuration and RF Output Power Setting Per KDB 353028 D01 Antennas Part 15 Transmitters v01 requirement, Applications must contain an exhibit listing each antenna, the antenna gain, antenna type, and antenna manufacturer/vendor and output power that can be used for the device, that the info listed below are correct and represent the product in consideration under this filing.