41 inch Painted Steel Tool Cart Model: EX4106TC 41” 6 Drawer Flip Top Tool Cart with Bumpers Model: EX4106TCS 41” 6 Drawer Sliding Top Tool Cart with Bumpers Extreme Tools, Inc. 740 Frontenac Road Naperville, Illinois 60563 630.369.9303 www.ExtremeTools.
Tool Cart with Flip Top Parts List EX4106TC 7 16 8 14 1 6 12 10 11 9 3 15 2 4 17 Optional Caster Locking Bracket
Tool Cart with Flip Top Parts List EX4106TC ITEM NO. PART NUMBER DESCRIPTION QTY. 1 EX4125TC-00 BODY WELDMENT 1 2 SW-150LB-2087B (OL) OUT. SLIDE (150#) 7 3 Z-DL4125TC DRAWER LINER 6 4 Z-CA6SB(CR) 6 X 2 CHROME CASTER (S/B) 4 5 Z-PR.188 3/16" SS POP RIVET 11 6 Z-SCM6-12MM M6-1.0X12 SOCKET HEAD SCREW 4 7 EX4125TC-40R LID ASSY - TC 1 8 GAS STRUT (350m13.
Tool Cart with Sliding Top Parts List EX4106TCS 4 5 16 17 5 8 10 17 9 18 10 19 1 12 11 20 3 21 20 Optional Caster Locking Bracket 12
Tool Cart with Flip Top Parts List EX4106TC ITEM NO PART NUMBER DESCRIPTION QTY 1 3 4 EX4125TX-00 (ST) SW-100LB-2087B SET EX4125TC-38STA BODY WELDMENT 100LBS., 20.87'' BB SLIDE (SET) SLIDING TRAY ASSEMBLY-RH 1 9 2 5 Z-HNDL4125TC SS TUBULAR HANDLE-4106TC 1 6 7 8 9 10 11 EX4125TC-44 Z-M4-6MS 304005 DR1-4125TC DR2-4125TC DR3-4125TC LOCK COVER M4-0.
ASSEMBLY Handle Installation NOTE: Install the handle first to make it easier to move the tool cabinet. Position the handle over the holes in the cabinet and attach with the provided (4) M6 Socket Head Screws. Tighten securely. Caster Installation NOTE: Lock the lid / sliding top and drawers BEFORE proceeding! Tool Cart is heavy. Installation requires assistance of another adult to complete this step.
Installing OPTIONAL Caster Locking Bracket To convert two of the casters from swivel to fixed, the OPTIONAL Caster Locking Bracket must be installed. 1. To install, first locate the (2) casters that are on the opposite side of the cart from the side handle. Fixed casters must be located opposite the side handle. Handle Casters 2. With the cart standing upright, move the cart so the brakes on the casters are facing the back of the cart - ALL CASTER BRAKES SHOULD BE FACING THE BACK OF THE CART.
3. Engage the brakes on all (4) casters. Locate the casters on the opposite side from the side handle. Loosen the (2) bolts & washers closest to the outer edge of the cart. DO NOT REMOVE BOLTS! ONLY LOOSEN THE BOLTS! 4. Slide the open slots of the Caster Locking Bracket into the gap between the washer and the caster plate. The long part of the bracket will slide in between the caster forks to prevent them from turning. Securely tighten the bolts. Installed Caster Locking Bracket 5.
OPERATING PROCEDURE Drawer Removal Pull drawer out so that it is almost fully extended. Push up on the black lever on one drawer slide and at the same time push down on the lever on the other side. With the levers in these positions, pull the drawer out until it releases from the drawer slides. Drawer Replacement Extend the drawer slides. Careful align the brackets on the sides of the drawers with the slots of the cabinet slides.
SAFETY WARNING Do not attempt to lift the cabinet by its side handle using chains, ropes or lifting device. Side handle may fail resulting in personal injury or damage to the product! Use a forklift or similar lifting device with forks placed under the bottom of the tool box to move if tool box cannot be moved by two people.