Owner’s Manual Professional Steel Hutches Models: RX723001HC 72”W x 30”D RX553001HC 55”W x 30”D 72 inch Steel Top Hutch Extreme Tools, Inc. 740 Frontenac Rd. Naperville, Illinois 60563 630.369.9303 www.ExtremeTools.net sales@extremetools.
3 18 17 18 1 13 21 13 17 16 27 19 14 22 RX723001HC Parts List 15 20 16 22 RX553001HC Parts List 28 ITEM NO PART NUMBER DESCRIPTION QTY ITEM NO PART NUMBER DESCRIPTION QTY 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 7225HC-01 7230HC-02 7230HC-05 Z-M5X16SHDS Z-M10PLUG GAS STRUT (350) POWER STRIP RUBBER GROMMET-2 7225HC-20 Z-SMS Z-M5X16PHMS Z-RB12M 7225HC-22 Z-M8-1.25-20SHS Z-WAFM8 7225HC-10 7225HC-13 RXPTUSL Z-M4-0.5LN Z-MSM4-0.
Step 1: Attach Splicer Posts to Side Panels Step 2: Install Side Panels on Roller Cabinet a. Slide Splicer Post Assembly (#9) into bottom opening of the left-hand Side Panel Assembly(#2). a. Remove plastic end caps from the top of the trim located at the front corners of the roller cabinet. NOTE: If the hutch is going to be used over the stainless steel surface, then remove the spacer on the bottom of the side panel. b.
Step 3: Secure Side Panels Step 4: Install Adjustable Shelf a. Loosely install one Hold-Down Bracket (#14) on each side using one flat washer (#16) and one M8 bolt (#15) for each side. a. Determine the desired height for the Adjustable Shelf. Pre-thread (2) screws (#11) about halfway in on left-hand and right-hand sides. If attaching the side locker or side box, do not use Hold-Down Bracket on that side. b. Locate the (2) open slots on each side of the shelf.
Step 5: Install Back Panel Step 6: Secure Back Panel a. Pull MDF board/Stainless Steel Top forward approximately 1/8” from Back Raised Edge (aka: Fence Rail.) c. Use (6) M5 screws (#11) on each side to fasten the back panel to side panel assemblies. b. Lift Back Panel into place behind the two side panels. (BACK PANEL is HEAVY and requires 2 people to place!) Slide the bottom edge of the Back Panel between the MDF/Stainless Steel Top and rear fence rail of roller cabinet.
Step 7: Attach Spacer Panel Step 8: Attach Gas Struts to Lid a. After the back panel has been installed, attach the spacer panel to the top section of the back panel. Use (3) M5x16mm pan head screws to secure spacer panel to top section of back panel. Use (4) addtional screws to attach the spacer to the top of both side panels. a. Lay the lid down on packaging material so that the front of the lid is face down. Be sure to use packaging material under the lid so that it does not get scratched or damaged.
Step 9: Install the Lid onto the body of the Hutch Step 10: Secure Lid to Body of Hutch LID is HEAVY! a. Use the Allen wrench (supplied with the parts) to drive the prethreaded M5-16mm Sock Head Screw (#4) into the round opening on the side of the lid. LID INSTALLATION REQUIRES ASSISTANCE to LIFT and MAY REQUIRE the USE of MECHANICAL EQUIPMENT to PROPERLY POSITION! b. Insert one plastic hole plug (#5) in each of the socket head screw openings. a.
Step 11: Secure Gas Strut to Side of Hutch Step 12: Final Details a. Prop open the lid so that it cannot fall. a. If you did not install the Hold Down Bracket in Step 3, then do so now. b. Install the male fitting on the piston end of the gas strut into the opening near the inside top of the side panel. b. Securely tighten ALL screws and bolts! c. Repeat for the gas strut on the other side.
