Use and Care Manual

EXTREME
STEAM
®
TURBO
HANDHELD STEAMER
INSTRUCTION BOOKLET
For your safety and continued enjoyment
of this product, always read the instruction
book carefully before using.
ALL GS108 MODELS
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety
precautions should always be taken, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING
DANGER – Any appliance is electrically
live even when the switch is off.
To reduce the risk of death by electric shock:
1. Always unplug appliance immediately
after use and before cleaning.
2. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
3. Do not place in or drop into water or
other liquids.
4. Do not reach for an appliance that has fallen
into water. Unplug immediately.
5. Use only in a dry area.
WARNING – To reduce the risk of
burns, electrocution, fire, or injury to persons:
1. This appliance should never be left
unattended when plugged in.
2. This appliance is not a toy and is not to be
used by children.
3. Close supervision is necessary when this
appliance is used near children or individuals
with certain disabilities. Unsupervised use could
result in fire or personal injury.
4. Use this appliance only for its intended
use as described in this manual. Do not
use attachments not recommended by the
manufacturer.
5. Rest the appliance on a stable surface when
placing on its base.
6. Never operate this appliance if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or damaged,
or if it has been dropped into water. Do not
attempt to repair the appliance. Incorrect
reassembly or repair could cause a risk
of fire, electric shock, or injury to persons
when the appliance is used. Return the
appliance to an authorized service center for
examination and repair.
7. Keep the cord away from heated surfaces.
Do not allow cord to contact heated surfaces.
Do not pull or twist cord. Let appliance cool
completely before putting away. Loop cord
loosely around appliance when storing.
8. To reduce the risk of electric shock, this
appliance has a polarized plug (one blade is
wider than the other). As a safety feature, this
plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety
feature.
9. Never drop or insert any object into
any opening.
10. Do not use outdoors or operate where
aerosol (spray) products are being used or
where oxygen is being administered.
11. If an extension cord is absolutely necessary,
a 15 ampere-rated cord should be used. Cords
rated for less amperage may overheat. Care
should be taken to arrange the cord so that the
cord cannot be pulled or tripped over.
12. Surfaces of this appliance are hot when
in use. Do not let heated surfaces touch eyes
or skin.
13. Do not place the steam nozzle directly on
any surface or on the appliance power cord
while it is hot or plugged in.
14. Unplug this appliance before filling or
emptying the water container and when not in
use.
15. Do not operate steamer without properly
filling the water container with distilled water.
16. Never yank cord to disconnect from
outlet; instead, grasp plug and pull
to disconnect.
17. Burns could occur from touching hot
surfaces, hot water, or steam. Use care when
removing water reservoir or when you turn a
steam appliance upside down – there may be
hot water in reservoir. Always position steamer
with head away from you and any other person
when turning on.
18. Do not hold hand in front of steam.
19. To reduce likelihood of circuit overload, do
not operate another high-wattage appliance on
the same circuit.
20. Use caution when installing or removing
an attachment, as it may contain hot water
from condensation. Ensure that the unit is off,
attachment is dry or cooled off to avoid contact
with hot water.
21. Never steam clothes you, or someone else,
are wearing.
22. When emitting steam, this appliance may
cause burns if it is used too close to the skin
or eyes, or if it is used incorrectly. To reduce
the risk of contact with hot water emitting from
the steam vents, test appliance before use by
holding it away from the body.
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
1. Fill water reservoir with distilled water.
2. Plug the unit into the electrical outlet.
3. Press the ON/OFF button located on the
back of the steamer to turn the unit on. The
HIGH SETTING light will illuminate and begin
blinking. Allow 10 seconds for the unit to
warm up. The appliance is ready to use when
the HIGH SETTING light stops blinking and
remains solid.
4. This steamer has a dry iron setting. Without
pressing the STEAM button, the soleplate of
the steamer will get hot to use as an iron.
5. The steamer has 4
steam settings. Press the
MODE button repeatedly
until you reach desired
setting. Choose LOW for
use on delicate fabrics,
up to TURBO for use on
thicker fabrics and heavily
wrinkled articles.
6. Press the STEAM button to emit steam. Pick
up steamer and begin steaming, pointing the
jets away from you and anyone in the room.
NOTE: This steamer has a SMART TOUCH
SENSOR feature. Steam will not emit until
steamer is picked up from flat surface.
7. To activate SMART TOUCH SENSOR, hold the
MODE button for 2 seconds until lights are
flashing. Once lights are flashing, the SMART
TOUCH SENSOR has been activated. Once
steamer is placed down on a flat surface,
SMART TOUCH SENSOR goes into auto pause.
To restart the steamer again, simply pick up
steamer and begin steaming.
8. Press ON/OFF button to turn unit OFF.
9. Unplug the device when it is not in use.
SANITIZING INSTRUCTIONS
1. P osition the garment steamer’s soleplate at
a minimum distance of 0.4 inch (1 cm) from
material to be treated.
2. Remain steaming in this position for 1 minute,
then move to the next area to be treated and
repeat.
ATTACHMENTS
CREASER ATTACHMENT -
Creates a crease in pants,
shirts, blouses and more.
DELICATES BONNET -
protects trims and safely steam
fine fabrics.
2-IN-1 ATTACHMENT
Silicone Band - pulls fabric
taut for better results.
Bristle Brush - ensures steam
penetrates fibers for a perfect
press, even on heavy fabrics.
USING ATTACHMENTS
With the garment steamer off and cool, snap
the Silicone Band, creaser or delicates bonnet
attachment over the steam head, ensuring it
is firmly affixed. At this point, for the 2-in-1
attachment, the Silicone Band can be used or
you can choose to affix either the Bristle Brush
insert into the channel on the top of the Silicone
Band attachment, as desired. NOTE: Only one
function of the 2-In-1 attachment can be used
at a time.
CAUTION: Use extreme care when changing
the attachments after the unit has been in
use, as the steam head will continue to be
hot.
STEAMING TIPS
1. First, test unit on an inconspicuous area of the
item to be steamed using the lowest STEAM
setting to ensure fabric can tolerate the effects
of steam. If there is no evidence of damage,
you can proceed to use the steamer on that
item.
2. To prepare your fabric for steaming, brush it
with the brush attachment. This will loosen the
fibers and allow better steam penetration.
3. Hang your garment or fabric. NOTE: Avoid
using metal clothes hangers, if possible.
CAUTION: If hanging garment on a door
while steaming, be careful not to damage
the door with steam.
4. Pass the steam jets just above the fabric
where the wrinkles are. It may take a few
passes to remove the wrinkles completely.
5. For heavier fabrics or severely wrinkled
fabrics, you may position the steamer head
directly on the fabric for a few seconds to
remove wrinkles. Be cautious when working
with delicate fabrics.
6. After use, turn unit off by depressing the
STEAM button. Then press the ON/OFF button
to the OFF position. With dry hands, unplug
your garment steamer from the outlet. Empty
any remaining water from the tank to avoid
leakage. BE SURE TO PRESS THE ON/OFF
BUTTON TO THE OFF POSITION PRIOR TO
UNPLUGGING THE UNIT.
7. When steaming, always keep the unit in
motion. Do not continuously hold steamer
over one area or touch steamer jets directly
to fabric for more than a few seconds, as
this can cause damage, including shrinkage,
melting, or color shift on certain types of
material.
8. In the case of heavier, durable fabrics, such
as wool coats or bedding, the TURBO setting
and slower passes with the steamer may
be necessary to achieve desired results. As
always, start by testing on an inconspicuous
area of the item to be steamed, using the
regular steam setting to ensure fabric can
tolerate the effects of steam, and adjust your
technique as needed to obtain the results
desired.
GETTING TO KNOW YOUR STEAMER
ON/OFF
button
STEAM
button
SETTING
indicator
lights
MODE
button
Soleplate
Water
reservoir
Built-in
stand
2-IN-1 ATTACHMENT
(A) Silicone Band -
Pulls fabric taut for
easier steaming.
(B) Bristle Brush -
Loosens fibers for better
steam penetration.
B.
A.
C.
D.
(C) Delicates Bonnet -
Helps protect delicate fabrics
and trims.
(D) Creaser -
For perfect pleats and folds.
CONAIR GARMENT
STEAMING ACCESSORIES
(sold separately)
Door Press Pad
Model GDPP1
Steaming Mitt
Model GPP1
Fabric Shaver
Model CLS1X
LIMITED ONE-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option)
your unit free of charge for 12 months from the
date of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return the
defective product to the service center listed,
together with your purchase receipt.
California residents need only provide proof of
purchase and should call 1-800-3-CONAIR
for shipping instructions. In the absence of a
purchase receipt, the warranty period shall be
12 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE 12-MONTH DURATION OF
THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER. Some states do
not allow the exclusion or limitation of special,
incidental, or consequential damages, so the
above limitation may not apply to you. This
warranty gives you specific legal rights, and you
may also have other rights, which vary from
state to state.
FEDERAL COMMUNICATIONS
COMMISSION NOTICE
WARNING: Changes or modifications to this
unit not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) This device must
accept any interference received, including
interference that may cause undesired
operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
SUPPLIER’S DECLARATION
OF CONFORMITY
Brand: Conair
®
Model No.: GS108
Description: Handheld Steamer
Responsible Party: Conair Corporation,
1 Cummings Point Road, Stamford, CT 06902
[phone]
Standards: FCC Part 15 Subpart B, ANSI
C63.4-2014
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that
may cause
undesired operation.
DATE OF ISSUE: 10/09/2020
IMPORTANT
FOR HOUSEHOLD USE ONLY
FILLING INSTRUCTIONS
1. Make sure the unit is unplugged.
2. Stand the unit on a table and grasp with one
hand.
3. Pull the reservoir out, away from the steamer
body.
4. The rubber inlet cover is located on the top
of the water reservoir.
5. Open the inlet cover and fill the reservoir
with distilled water (which can be found in
grocery stores). We recommend that you
use distilled water only, as this will prevent
mineral deposits in the boiler that can reduce
performance or clog the water system.
6. Close the inlet cover and return the reservoir
to its place, making sure that it snaps in
place and is secure.
Rubber Inlet Cover
Due to continuing product improvements,
the actual product purchased may differ
slightly from the one shown.
Service Center
Conair Corporation
Service Department
7475 N. Glen Harbor Blvd.
Glendale, AZ 85307
For information on any Conair product, call
1-800-3-CONAIR or visit us on the web at
www.conair.com
Please register this product at
www.conair.com/registration
©2021 Conair Corporation
Made in China
21PA075297
IB-16995