User’s Manual CVEQ 100 Series and SVEQ 100 Series Composite Video or S-Video and Audio Line Drivers with Gain and Equalization www.extron.com Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort, The Netherlands +800.3987.6673 +31.33.453.4040 FAX +31.33.453.4050 Extron Electronics, Asia 135 Joo Seng Rd. #04-01 PM Industrial Bldg., Singapore 368363 +800.7339.8766 +65.6383.4400 FAX +65.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 (地线)是安全设施,不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后 或桌面电源的电源线,或任何接到市电系统的电源线。 露的危险电压,有触电危险。 电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
Quick Start Guide — CVEQ/SVEQ 100 Series C Installation and service must be performed by authorized personnel only. These line drivers must be used with UL approved, grounded electrical boxes. To install and set up the line driver, follow these steps and see the appropriate sections of this manual for details. Step 1 Turn the input and output devices off and unplug their power cords. Verify that the line driver is disconnected from the power source before proceeding.
Quick Start — CVEQ/SVEQ 100 Series, cont’d When using long cables, follow these steps: a. Supply the color bars test signal to the input. (Recommendation: use an Extron VTG 300 Video Test Generator to generate the test signal.) b. Adjust the Gain control(s) for the output until the signal level at the far end is the same as the input (or the display shows the correct brightness and contrast). c.
Table of Contents, cont’d Appendix B • Dimensions and Template ...................... B-1 Decora Models Dimensions . ................................................... B-2 Cut-out Template ........................................................................ B-3 All trademarks mentioned in this manual are the properties of their respective owners. 68-1442-01 Rev.
Introduction About this Manual This manual contains information about the Extron composite video CVEQ 100 Series, and the S-video SVEQ 100 Series of high performance 1-input, 1-output video line drivers. Both series of line drivers support stereo or dual mono audio (balanced or unbalanced). These line drivers can drive video signals up to 1000 feet using Extron MHR cable.
Installation Application Examples Extron SI 26X Two-way Ceiling Speakers To get started, refer to the "Quick Start Guide" at the beginning of this manual. C Audio Installation and service must be performed by authorized personnel only. L 2 4/8 A 12 MP UTS RS TP KE OU SPEA ms R S-video Oh L US C TE MO UTS RE INP E R L Extron SI 26 Surface-mount Speakers UT TP OU Y T PU IN Extron MPA 122 Mini Power Amplifier V 10 L/MUT VO L WER PO R .
Installation Installation Instructions The following sections explain the installation of the CVEQ 100 and SVEQ 100 series of line drivers. Installing the CVEQ 100/SVEQ 100 Mounting the CVEQ 100 and SVEQ 100 The CVEQ 100 composite video line driver and the SVEQ 100 S-video line driver can be set on a table, mounted on a rack shelf, mounted under a desk or table, mounted through furniture (CVEQ 100 only), or mounted on the back of a rack (SVEQ 100 only).
QuarterRackStandardShelf Installation QuarterRackUnderdeskMounting 1U Universal Rack Shelf 1/2 Rack Width Front False Faceplate 1/4 Rack Width Front False Faceplate Furniture mounting — under-desk To mount the line driver under furniture, use the optional VersaTools under-desk mounting kit for the SVEQ 100 (Extron MBU 123, part #70-212-01) or the optional under-desk kit for the CVEQ 100 (Extron MBU 125, part #70-077-01). Both front false faceplates use 2 screws.
Installation 9. Attach input and output cables. See chapter 3. Back of the rack mounting (SVEQ 100 only) The SVEQ 100 can be mounted to the rear of a rack using the BackofRackMountingEars Extron VersaTools MBB 100 back of the rack mounting kit (part #70-367-01). The kit allows the product to be vertically mounted to the front or rear rack supports and facing either towards the front or the rear of the rack. Preparing the CVEQ 100 for through-desk mounting 1.
Installation, cont’d Installing the CVEQ 100 AAP/SVEQ 100 AAP The CVEQ 100 AAP and SVEQ 100 AAP are double space high architectural adapter plate products that mount in a wall or furniture using an optional mounting frame. 1. Remove power from the line driver by disconnecting the power supply. 2. Attach the mounting frame to wall box. 3. Route output cables through the wall box and frame and connect them to the line driver. 4.
Installation, cont’d Installing the CVEQ 100 MAAP/SVEQ 100 MAAP The CVEQ 100 MAAP and SVEQ 100 MAAP are three space high mini architectural adapter plate products that mount in a wall or furniture using an optional mounting frame or European cable channel system. Mounting in an external wall box 1. Remove power from the line driver by disconnecting the power supply. 2. Attach the mounting frame to the wall box. 3. Route output cables through the wall box and frame, and connect them to the line driver.
Installation, cont’d Installing the CVEQ 100 D/SVEQ 100 D The CVEQ 100 D and SVEQ 100 D are wall-mounted products and can be mounted into an electrical wall box. This section includes site preparation, wall box installation, and the mounting of the line driver in the wall box. Wall Stud Installation Cable Wall Stud Installation Cable Cable Clamp Cable Clamp Screws or Nails Screws or Nails N The line driver must be installed into an Underwriters Laboratories (UL) approved electrical wall box.
Installation, cont’d 4. Mount the line driver to the wall box with machine screws as shown in the following illustration. 3. Check the video source’s user’s guide or contact Extron to determine if there are special requirements to output video to the external video port. 4. Call the Extron S3 Sales and Technical Support Hotline if the image still does not appear or there is no sound. If the image is not displayed correctly 1.
Installation, cont’d CVEQ 100 and SVEQ 100 Series 3 Chapter Three Operation Front Panel Features and Operation Rear Panel Features and Operation Replacing the Decora Faceplate (CVEQ 100 D and SVEQ 100 D) 2-18 CVEQ 100 and SVEQ 100 Series • Installation
Operation Front Panel Features and Operation GAIN V ID E O IN 1 EQ 4 A U D IO IN CVEQ 100 VIDEO LINE DRIVER 1 2a CVEQ 100 Front Panel 3 L R CVEQ 100 M AAP CVEQ 100 MAAP Front Panel 6 GAIN Y C GAIN EQ S -V ID E O IN 1 SVEQ 100 5 S-VIDEO LINE DRIVER 1 2a 3 A U D IO IN SVEQ 100 Front Panel 2b L R SVEQ 100 M AAP V ID E O IN A U D IO IN SVEQ 100 MAAP Front Panel 6 L R C V E Q 100 A A P 1 CVEQ 100 AAP Front Panel 6 4 Faceplate 1 S-V ID E O IN AUDIO IN VIDEO IN 3-2 6 R 5
Operation a Ç É c d e Power indicator LED — This LED lights: • Amber when the line driver is receiving full power (this applies to all models except the CVEQ 100 and SVEQ 100, which light green instead). • Green when the line driver is receiving a video signal (this only applies to the D, AAP, and MAAP models).
Operation Rear Panel Features and Operation L L VIDEO 2a 1 5 OUTPUT INPUT 12V 0.
Operation, cont’d 9 1 R DUAL MONO 5 L G A IN STEREO EQ 7 V ID E O 6 A U D IO O U T P U T 9 POW ER 1 2V 0 .2 A M A X 4a 1 CVEQ 100 MAAP Rear Panel R DUAL MONO 1 9 5 L G A IN A U D IO O U T P U T Y STEREO EQ 7 7 CVEQ 100 D Rear Panel 4a 9 6 6 5 POW ER 1 2V 0 .
Operation, cont’d f Tip (+) Sleeve ( ) Ü á Video output connector — Connect a composite video output device to this female BNC connector. S-video Y connector (luma, white cable) — Connect the luma of an S-video output device to this female BNC connector. g S-video C connector (chroma, yellow cable) — Connect the chroma of an S-video output device to this female BNC connector. e Audio output connector — Wire a balanced/unbalanced audio output device to this 3.
Operation, cont’d C Power supply voltage polarity is critical. Incorrect voltage polarity can damage the power supply and the line driver. Identify the power cord negative lead by the ridges on the side of the cord. To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter. W The two power cord wires must be kept separate while the power supply is plugged in. Remove power before wiring.
Operation, cont’d CVEQ 100 and SVEQ 100 Series A Appendix A Specifications, Part Numbers, and Accessories Specifications Included Parts Optional Accessories 3-14 CVEQ 100 and SVEQ 100 Series • Operation
Specifications, Part Numbers, and Accessories Specifications Video Gain.................................................. Composite video and Y of S-video: -1 dB to +3 dB (x0.9 to x1.4), adjustable C of S-video: 0 dB to +10 dB (x1 to x3), adjustable Equalization.................................... 0 dB to +7 dB (x1 to x2) at 5 MHz, adjustable Bandwidth (Y of S-video).............. 185 MHz (-3 dB) Output cable driving distance......
Specifications, Part Numbers, Accessories, cont’d Audio output Number/signal type CVEQ 100, SVEQ 100......... 1 stereo, balanced/unbalanced All other models................. 1 stereo or dual mono (switch-selectable), balanced/unbalanced Connectors...................................... (1) 3.5 mm captive screw connector, 5 pole Impedance....................................... 50 ohms unbalanced, 100 ohms balanced Nominal level.................................
Specifications, Part Numbers, Accessories, cont’d Shipping weight CVEQ 100, SVEQ 100......... 3 lbs (2 kg) All other models................. 2 lbs (1 kg) Vibration.......................................... ISTA 1A in carton (International Safe Transit Association) Listings............................................ UL, CUL Compliances.................................... CE, FCC Class A, VCCI, AS/NZS, ICES MTBF................................................ 30,000 hours Warranty............................
Specifications, Part Numbers, Accessories, cont’d These items are included in each order of the CVEQ 100 MAAP or SVEQ 100 MAAP.
Specifications, Part Numbers, Accessories, cont’d These items are optional accessories for the CVEQ 100 D or SVEQ 100 D.
Specifications, Part Numbers, Accessories, cont’d CVEQ 100 and SVEQ 100 Series B Appendix B Dimensions and Template Decora Models Dimensions Cut-out Template A-12 CVEQ 100 and SVEQ 100 Series • Specifications and Parts
Dimensions and Template Cut-out Template Decora Models Dimensions Dimensions are shown in inches [mm}. N Always check and go by the dimensions given in this .000 [0.000] 1.700 [43.00] appendix. The template is not full size. Cut-Out Template for the Extron CVEQ 100 D & SVEQ 100 D .060 [1.524] .600 [15.500] .100 [2.540] 2.79" (7.09 cm) 2.830 [71.882] 0.000 [0.000] 2.720 [69.088] Wall Plate 2.040 [51.816] 1.465 [37.211] 1.75" (4.5 cm) 0.790 [20.066] Location of Line Driver 0.110 [2.794] 2.
Dimensions and Template B-4 CVEQ 100 and SVEQ 100 Series • Dimensions and Template