User’s Guide DVI DA Plus Series DVI Distribution Amplifiers 68-1536-01 Rev.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
Quick Start Guide — DVI DA Plus Series To install, connect cables, and operate any of the DVI DA Plus Series distribution amplifiers, follow these steps: Step 1: Install Install the distribution amplifier on a desk, under a desk, or in a rack (see page 2-2). Step 2: Connect Power Cables Connect the 12 VDC power supply (provided with the unit) to the unit's power receptacle, using the two pole, 3.5mm captive screw connector (see page 2-8). POWER 12V 1.
Quick Start Guide — DVI DA Plus Series, cont’d Step 3: Connect DVI Cables Connect a DVI cable from the Input connector to the video source device (see page 2-9). Connect a DVI cable from the distribution amplifier to the desired display device(s) (see page 2-9). us 8 Pl I DA DV 8 7 6 5 UT TP I-D DV OU 4 3 2 1 UT I-D INP DV Extron DVI DA8 Plus R WE PO 12V MAX A Display with DVI Input 0.
Table of Contents Chapter One • Introduction ..................................................... 1-1 About This Manual .................................................................... 1-2 About the DVI DA Plus Series . ............................................... 1-2 DVI DA Plus Series Features .................................................... 1-3 Chapter Two • Installation and Operation . .................. 2-1 Installation Overview . ...........................................................
Table of Contents, cont’d ii DVI DA Plus Series • Table of Contents
DVI DA Plus Series 1 Chapter One Introduction About this manual About the DVI DA Plus Series DVI DA Plus Series Features
Introduction About This Manual This manual describes the installation, operation, and specifications of the Extron DVI DA4 Plus, DVI DA6 Plus, and DVI DA8 Plus Distribution Amplifiers. Unless stated otherwise, all references to the "distribution amplifier" or "DVI DA Plus Series" in this manual refer to the features or operation of all three models.
DVI DA Plus Series Features EDID Minder — The EDID Minder maintains continuous EDID (Extended Display Identification Data) communication with the attached source. This ensures that the DVI source powers up correctly and maintains a proper video output, even if the display is off. High Resolution DVI-D input — The distribution amplifiers accept one single link DVI-D input, with a resolution range up to 1920 x 1200 or 1080p @ 60 Hz.
Introduction, contd 1-4 DVI DA Plus Series • Introduction
DVI DA Plus Series 2 Chapter Two Installation and Operation Installation Overview Mounting the Distribution Amplifier Front Panel Features Rear Panel Features Operation Troubleshooting
Installation and Operation Installation Overview All three distribution amplifiers can be mounted on tabletops, under furniture, and in racks by following these steps: 1. Ensure that the input sources, the distribution amplifier and the output display(s) are all turned off and all power sources and signal cables are disconnected. 2. Mount the unit as described in "Mounting the Distribution Amplifier", below. 3. Connect the cables (see page 2-9). 4.
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted equipment. Pay particular attention to supply connections other than direct connections to the branch circuit (such as the use of power strips). Rack mounting the DVI DA4 Plus The DVI DA4 Plus can be mounted on the following (optional) rack shelves: • RSF 123 (3.5" deep, 1U rack shelf kit: part # 60-190-20) • RSB 123 (3.
Installation and Operation, cont’d Rack mounting the DVI DA6 Plus and DVI DA8 Plus The DVI DA6 Plus and DVI DA8 Plus distribution amplifiers can be mounted using the Extron MBD 149 rack mount kit (provided) as follows: 1. Remove rubber feet if these have been installed on the bottom of the unit. 2. Secure one bracket to each side of the distribution amplifier with the provided bracket mounting screws (four #8 screws for each bracket — see the figure below).
Under-desk mounting Mount the DVI DA6 Plus or DVI DA8 Plus (not shown) under furniture, using the optional Extron MBU 149 under-desk mounting kit (part # 70-222-01). Mount the DVI DA4 Plus using the optional Extron MBU 125 under-desk mounting kit (part # 70-077-01) as shown in the figure below. Follow the same instructions with either kit: Under furniture mounting the DVI DA4 Plus To mount the unit under a desk or table: 1. If necessary, remove rubber feet from the bottom of the unit. 2.
Installation and Operation, cont’d Front Panel Features The front panels for the DVI DA4 Plus (upper panel) and the DVI DA6 Plus/DVI DA8 Plus (lower panel) are shown below: DVI DA PLUS DVI DISTRIBUTION AMPLIFIER 1 DVI DA Plus SERIES DVI DISTRIBUTION AMPLIFIER 1 Front panel features a 2-6 LED indicator — This LED indicator illuminates amber when the unit is receiving power but no input signal. When the unit detects an input signal, the LED illuminates green.
Rear Panel Features The rear panels for the DVI DA4 Plus (top panel), the DVI DA6 Plus (middle panel), and DVI DA8 Plus (bottom panel) are shown below: DVI DA4 Plus POWER 12V 1.0A MAX DVI-D INPUT 2 3 DVI-D OUTPUT 1 2 3 4 4 DVI DA6 Plus POWER 12V 1.5A MAX 2 DVI-D OUTPUT DVI-D INPUT 1 2 3 3 4 5 6 5 6 4 DVI DA8 Plus POWER 12V 1.5A MAX DVI-D OUTPUT DVI-D INPUT 1 2 3 4 7 8 Rear panel features b c d Power input — Connect the external power supply (provided) to the 3.
Installation and Operation, cont’d Power supply input Connect the two pole, 3.5 mm captive screw connector from the power supply (provided with the unit) to this orange socket on the rear panel. POWER 12V 1.0A MAX Back Panel Power Receptacle DC Power Cord Captive Screw Connector Ground +12 VDC AC Power Cord External Power Supply (12 VDC, 2 A ) The external power supply in the illustration above (12 VDC, 2A) is for use with the DVI DA4 Plus.
Input cable connections Connect a single link DVI-D source device, with a resolution range up to 1920 x1200 or 1080p @ 60 Hz, to the female DVI-I input, using a DVI cable. N Although these distribution amplifiers have DVI-I connectors, they are only compatible with single-link DVI-D video signals. Input EQ conditions input signals to ensure the integrity of the signals delivered to the output devices.
Installation and Operation, cont’d DVI connector pin assignments The illustration below shows the pin assignments for the DVI-I connectors. N Although DVI-I dual link connectors are used, these distribution amplifiers are only compatible with singlelink DVI-D video signals.
Operation 1. Connect the captive screw connector from the supplied 12 VDC power supply into the power receptacle on the rear panel. Do not power on the power supply yet. 2. Connect the source device to the DVI input receptacle on the rear panel. 3. Run cables from the display device(s) and connect them to the DVI output receptacles on the rear panel. 4. Power on the display device(s). 5. Power on the distribution amplifier. The LED will light amber to show that the unit is receiving power. 6.
Installation and Operation, cont’d Troubleshooting No output signal — Check that the front panel LED is on (amber shows that the unit is receiving power, green shows that it is also receiving an input signal). If LED is not lit, check the power supply and/or video input connections to the unit (see page 2-6). No output signal or poor quality signal — Check the integrity of the cabling from the source device to the distribution amplifier and from the distribution amplifier to each of the display devices.
DVI DA Plus Series A Appendix A Reference Information Specifications Included Parts Accessories
Reference Information Specifications N *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. Video Maximum data rate....................... Maximum pixel clock.................... Resolution Range........................... Formats............................................ Standards......................................... 4.95 Gbps (1.65 Gbps per color) 165 MHz Up to 1920 x 1200 or 1080p @ 60 Hz RGB and YCbCr digital video DVI 1.0, HDMI 1.
Enclosure dimensions DVI DA4 Plus.....................1.75" H x 8.75" W x 3.0" D (1U high, half rack wide) 4.4 cm H x 22.2 cm W x 7.6 cm D (Depth excludes connectors.) DVI DA6 Plus, DVI DA8 Plus 1.75" H x 17.5" W x 8.5" D (1U high, full rack wide) 4.4 cm H x 44.4 cm W x 21.6 cm D (Depth excludes connectors.) Product weight............................... 2.8 lbs (1.3 kg) Shipping weight............................. 5 lbs (3 kg) Vibration..........................................
Reference Information Included Parts These items are included in each DVI DA Plus series amplifier: Included parts Replacement part number DVI DA4 Plus 60-846-01 DVI DA6 Plus 60-932-01 or DVI DA8 Plus 60-933-01 12 VDC, 2A Desktop power supply with orange captive screw attached (for use with DVI DA4 Plus) 28-181-05LF 12 VDC, 3A Desktop power supply with orange captive screw attached (for use with DVI DA6 Plus and DVI DA8 Plus) 28-113-05LF (1) IEC cord (4) Rubber feet (not attached) MBD 149 rack m
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron EMEA Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.
