User’s Guide DVI 104 Tx/Rx Fiber Optic Transmitter and Receiver 68-1549-01 Rev.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 （地线）是安全设施，不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 或桌面电源的电源线，或任何接到市电系统的电源线。 露的危险电压，有触电危险。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
Description The DVI 104 Tx and DVI 104 Rx are fiber optic transmitter/ receiver units that extend DVI signals up to 1,640' (500 m) using four multi-mode fiber optics cables. The transmitter plugs directly into the source device and the receiver plugs directly into the display device. The transmitter/receiver pair can handle DVI video signals with resolutions up to 1920 x 1200 or 1080p @ 60 Hz. Optional four-fiber Multi Mode cables are available in varying lengths.
DVI 104 Tx/Rx, cont’d Features Power Supply — Separate power supplies are provided for both the transmitter and receiver. Power LEDs — The LEDs are on the top and bottom panels of both the receiver and transmitter. They illuminate blue when the unit is receiving power. No mounting hardware required — The units plug directly into the source device (transmitter) or output device (receiver) and take up very little space.
b LC Jacks — Four fiber optic cables connect the transmitter to the receiver. The cables connect to the four female LC jacks in each of the units. A label on the top panel identifies the unit as the transmitter or receiver and identifies the fiber optic port numbers and the power input. N For the transmitter, port 1 is closest to the power input and port 4 is furthest away. For the receiver, the ports are in the reverse orientation: port 4 is closest to the power input and port 1 is furthest away.
DVI 104 Tx/Rx, cont’d Rear panel features 1 3 6 8 3 Male Connector 9 c 17 19 22 24 A single-link DVI-D male connector is used to connect the transmitter to the source and the receiver to the output device.
f Label — a label on the top panel identifies the unit as the transmitter or receiver and also identifies the fiber optic port numbers and the power input. Bottom panel features The bottom panels of both the transmitter and receiver have a label that identifies the unit’s serial number and a second power LED that lights blue when the unit is receiving power.
DVI 104 Tx/Rx, cont’d Setup and Operation By default, the transmitter/receiver pair are set to extend video signals with a resolution of 1600 x 1200 @ 60 Hz. For display devices that support this resolution and refresh rate, proceed to step 7. Otherwise, it is necessary for the transmitter to capture and store the EDID of the display device, which is explained in steps 1-6. 1.
7. Apply power to the receiver by inserting the cable from the external power supply into the input jack. The LED should illuminate a solid blue. 8. Ensure that the display device is still powered on, connect the receiver directly to the DVI input, and tighten the thumbscrews. 9. Ensure that the PC or source is powered off, connect the transmitter directly to the DVI input, and tighten the thumbscrews. 10.
DVI 104 Tx/Rx, cont’d Trouble Shooting Display does not show an image • Ensure that all plugs and jacks used by the external power supplies are firmly connected. If the cable is loose or slips out of the slot easily, move the release catch from its normal position above the locking catch, to the adjusted position under the locking catch (see the figure below). This provides the extra leverage required to keep the locking catch in place and hold the cable securely.
Screen is distorted or displays noise • Ensure that the cable length does not exceed 1,640' (500 m). • Ensure that the cables are high quality Multi Mode cable and are terminated with securely fitting plugs. • Ensure that the graphic resolution is correctly set (see “Setup and Operation”). • View the “Display Properties” of the source device to check the output resolution. The resolution and refresh rate must match the capabilities of the display device and must not exceed 1920 x 1200 at 60 Hz.
DVI 104 Tx/Rx, cont’d Specifications N The DVI 104 TX/RX consists of a transmitter (DVI 104 TX) and a receiver (DVI 104 RX) with fiber optic cables linking the two units. N These transceivers are Class 1 laser products. They meet the safety regulations of IEC-60825, FAD 21, CFR 1040.10, and FDA 21 CFR 1040.11. Optical fiber interconnection between transmitter and receiver Number/type................................. 4 fiber optic, multimode Connectors......................................
Cooling............................................ Mounting Rack mount......................... Furniture mount................. Enclosure type ............................... Enclosure dimensions . ................. Convection, no vents No No Plastic 0.6" H x 1.5" W x 2.3" D (1.5 cm H x 3.9 cm W x 5.9 cm D) (Depth excludes DVI connector.) Product weight............................... 0.7 lbs (0.3 kg) per TX/RX pair Shipping weight............................. 1 lb (<1 kg) per TX/RX pair Vibration . ....
DVI 104 Tx/Rx, cont’d Parts Included parts Included Parts Replacement part number DVI 104 Tx/Rx 60-977-01 (2) 5 VDC Power Supply DVI 104 Tx/Rx User’s Guide Fiber optic cables 12 Accessories Part number 4-fiber MM LC-LC - 10 m (32.8') 26-652-01 4-fiber MM LC-LC - 20 m (65.6') 26-652-02 4-fiber MM LC-LC - 30 m (98.4') 26-652-03 4-fiber MM LC-LC - 40 m (131.2') 26-652-04 4-fiber MM LC-LC - 50 m (164.0') 26-652-05 4-fiber MM LC-LC - 60 m (196.9') 26-652-06 4-fiber MM LC-LC - 70 m (229.
Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Dubai +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.
