- Extron 60-1043-12 XTP Transmitter Manual
1
Product Category
XTP T HDMI and XTP R HDMI • Setup Guide
This guide provides instructions for an experienced installer to install and connect the Extron XTP T HDMI transmitter and XTP R HDMI receiver.
Transmitter Connections Receiver Connections
a DC power connector
b HDMI input connector
c HDMI Loop-thru connector
d Analog audio input connector
e RS-232/IR Over XTP
connector
f XTP output connector
g LAN connector
h DC power connector
i XTP input connector
j LAN connector
k RS-232/IR Over XTP connector
l HDMI output connector
m Analog audio output connector
n S/PDIF audio output connector
o Relay connectors
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required.
Step 2 — Connecting inputs
a. Connect a digital video source to the female HDMI connector of the XTP T HDMI (see b above). It can accept HDMI, DVI (with an
appropriate adapter), or DisplayPort video signals.
NOTES:
• Use an Extron LockIt
®
Locking Bracket to secure HDMI cables to the connectors.
• Video input from a DisplayPort source must be a dual mode DisplayPort source.
b. Connect a digital video display to the HDMI loop-thru connector on the transmitter to locally display the input source. Displays that are not
HDCP compliant display a green screen when HDCP encrypted content is sent to them (see c above).
c. Connect balanced or unbalanced stereo audio to the
3.5 mm, 5-pole captive screw connector (see d above).
Step 3 — Connecting Throughput Devices
a. Connect a twisted pair cable between the XTP connectors on
the transmitter and receiver (see f and i above).
ATTENTION: Do not connect these connectors to a computer data or telecommunications
network.
The XTP T HDMI and XTP R HDMI are compatible with CAT 5e, 6, 6a, and 7 shielded twisted pair
(F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable. Extron recommends using
the following practices to achieve full transmission distances up to 330 feet (100 m) and reduce
transmission errors.
z Use Extron XTP DTP 24 SF/UTP cable for the best performance. If not using XTP DTP 24
cable, at a minimum, Extron recommends 23 AWG, solid conductor, STP cable with a minimum
bandwidth of 400 MHz.
z Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.
z Limit the use of more than two pass-through points, which may include patch points, punch
down connectors, couplers, and power injectors. If these pass-through points are required, use
CAT 6 or 6a shielded couplers and punch down connectors.
NOTE: When using CAT 5e or CAT 6 cable in bundles or conduits, consider the following:
• Do not exceed 40% ll capacity in conduits.
• Do not comb the cable for the rst 20 m, where cables are straightened, aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook and loop fasteners.
• Separate twisted pair cables from AC power cables.
Signal LED — Lights on the transmitter when it is transmitting a video signal or a test pattern. Lights on the receiver when it receives an
active XTP input signal from the transmitter.
Link LED — Lights yellow when a valid link between an XTP input and output is established.
TIA/EIA T 568 B
Pin Wire Color
1 White-orange
2 Orange
3 White-green
4 Blue
5 White-blue
6 Green
7 White-brown
8 Brown
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Do not tin the wires!
Unbalanced Stereo InputBalanced Stereo Input
Tip
Ring
Tip
Ring
Sleeves
Tip
Sleeve
Sleeve
Tip
LR
LR
POWER
12V
HDMI
1.0 A MAX
Rx GTx
RS-232 IR
RxTx
−+−+
LR
LOOP-THRU
RESET
AUDIO
OFF
ON
AUDIO
LAN
SIG LINK
XTP OUT
INPUTS
OVER XTP
POWER
12V
1.0 A MAX
Rx GTx
RS-232 IR
RL
RxTx
-+-+
1
2
AUDIO
ON
AUDIO
RESET
OVER XTP
OUTPUTS RELAYS
SIG LINK
XTP IN
LAN
HDMI
OFF
S/PDIF
XTP R HDMI Rear Panel
XTP T HDMI Rear Panel
g
a
b
k
m
n
h
ij
f
d
c
o
e
l