User’s Manual EDID 101D & EDID 101V EDID Emulator with EDID Minder™ 68-1773-01 Rev.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 (地线)是安全设施,不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后 或桌面电源的电源线,或任何接到市电系统的电源线。 露的危险电压,有触电危险。 电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 没有用户可以更换的零件。为避免出现触电危险不要自 己试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 与厂家推荐的相同
Table of Contents About this Manual ........................................................................ 1 About the EDID 101 ...................................................................... 1 EDID 101 Features ......................................................................... 2 Mounting the EDID 101 ............................................................... 5 Tabletop placement ................................................................... 5 Rack mounting ........................
About this Manual This manual contains information about the Extron EDID 101D/EDID 101V, with instructions on how to mount and operate the unit. Throughout this manual EDID 101 is used to refer to the EDID 101D and EDID 101V. Where differences may occur, they are noted. About the EDID 101 The EDID 101D and EDID 101V are compact, economical EDID Minder™ devices that record and manage display EDID (Extended Display Identification Data). A source device normally uses EDID to identify the signal type (i.e.
Introduction EDID 101 Features EDID Minder — Enables continuous EDID communication to the input source. EDID provides information about a display identity. The EDID Minder continuous EDID communication helps ensure the source boots up properly and reliably outputs content to the display. EDID Record — Enables the device to record EDID directly from a display. Pre-programmed EDID — The EDID 101 contains pre‑programmed EDIDs with the most common display native resolutions for both 50 and 60 Hz.
DVI OUTPUT (DISPLAY) DVI INPUT (SOURCE) Mac-Mini EDID 101D DVI-DVI DVI-DVI DVI DA2 DVI DISTRIBUTION AMPLIFIER DVI-DVI DVI DA2 Projector D-SUB NPUT (SOURCE) D-SUB OUTPUT (DISPLAY) EDID 101D VGA-VGA PC EDID 101V EDID to PC VGA-VGA (No EDID Passed) AUDIO IN COMPUTER IN RGB LEVEL PEAKING MTP SERIES Twisted Pair MTP 15 HD A D MTP RL 15 HD RS VGA-VGA Projector EDID 101V Typical EDID 101 applications EDID 101D/EDID 101V • Introduction 3
Introduction, cont’d 2 1 4 3 2 L R L 232 RS R 1 DIO S AU UT TP OU L V R DIO AU UTS INP H B G 1 S UT R 2 1 V H HV V 4 3 HV HV TP OU 2 ON H B G 3 R V H 4 S UT INP B 1.
Mounting the EDID 101 The EDID 101 is housed in a 1/8 rack width, 3" deep, 1" high metal enclosure. The small form factor is ideal for connecting the EDID 101 between two devices that would otherwise be directly connected. N After the EDID 101 is mounted, the side panel may be inconvenient or impossible to access for configuration. To avoid uninstalling, program it prior to mounting. See page 10, "EDID 101D/EDID 101V Operation" for programming details.
Installation and Operation, cont’d Rack mounting procedures The unit can be mounted in the front or rear of any of these rack systems: • RSF 123 rack shelf kit for 3.5" deep products (part #60-190-20) • RSB 123 basic rack shelf kit for 3.5" deep products (part #60-604-20) • RSU 126 universal rack shelf kit for 6" deep products (part #60-190-10) • RSB 126 basic rack shelf kit for 6" deep products (part #60-604-10) • RSU 129 universal rack shelf kit for 9.
Furniture mounting The EDID 101 can be mounted under furniture using optional mounting kit MBU 125 (part #70-077-01) as follows: 1. Attach the mounting brackets to the EDID 101 with the provided machine screws as shown in the figure below. 2. Hold the EDID 101 with the attached brackets against the underside of the table or other furniture. Mark the location of the screw holes in the brackets on the mounting surface. 3. Drill 3/32" (2.4 mm) diameter pilot holes, 1/4" (6.
Installation and Operation, cont’d Panel Features EDID 101D ON 1 DVI OUTPUT (DISPLAY) RECORD g 2 60 DIGITAL Hz SIGNAL 50 ANALOG ab cd EDID SELECT POWER 12V 0.4A MAX EDID 101V DVI INPUT (SOURCE) e f ON CONFIG 1 VGA OUTPUT (DISPLAY) 2 EDID SELECT 60 RECORD Hz 50 SPARE POWER 12V 0.
Front and rear panels e Power connector — An optional external 12 VDC power supply may be connected to this 2-pole, 3.5 mm captive screw connector. N f g During normal operation the EDID 101 is powered using +5 VDC from pin 9 of a DDC compliant VGA source (EDID 101V) or pin 14 of a DVI source (EDID 101D). If the source is capable of providing power for the EDID 101, the green Power LED (a) will light when the source is connected and powered on.
Installation and Operation, cont’d EDID 101D/EDID 101V Operation The EDID 101 can either record EDID from a display device or a pre‑programmed EDID can be selected using the rotary and DIP switches. Recording a display EDID To record a new EDID into memory: 1. Turn the rotary switch (d) to position 0. N 2. Apply power to the EDID 101 by connecting a power source. N 3.
Using the pre-programmed Extron EDID Configuring the EDID 101 rotary and DIP switches allow a user to select a pre-programmed EDID based on the native rate of a display (i.e. 1280x1024 @ 60 Hz) and a desired signal type (i.e. digital), but does not necessarily force a video source to output that rate. Since EDID is not limited to reporting a single video rate (i.e. the native rate), each Extron EDID also lists other common video rates for use by the video source.
Reference Material Specifications N If you use a DVI-A to 15-pin HD adapter, the EDID 101D can be used for analog signal pass-through. Video — EDID 101D, digital signals Maximum data rate ���������������������� Maximum pixel clock ������������������� Resolution range ��������������������������� Formats ������������������������������������������� Standards ���������������������������������������� 10 Gbps (3.
General Power ���������������������������������������������� Supplied by the 5 V signal from a DVI source (pin 14), a VGA* source (pin 9), or from an external power supply N *Some VGA source devices do not provide power output. External power supply ����������������� 100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated Power input requirements ����������� 12 VDC, 0.
Reference Material, cont’d Included Parts These items are included in each order for an EDID 101: Included parts EDID 101D -or- EDID 101V Replacement part number 60-990-01 60-991-01 (4) Rubber feet (unattached) (2) Strips of Velcro (unattached) EDID 101D/EDID 101V Setup Guide Accessories Accessories 14 Part number PS 1210C 12 VDC, 1 A power supply 70-775-01 RSU 129, universal rack shelf kit for 9.5" deep products (gray) 60-190-01 RSB 129, basic rack shelf kit for 9.
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase.
Extron USA - West Headquarters +800.633.9876 Inside USA / Canada Only +1.714.491.1500 +1.714.491.1517 FAX Extron USA - East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East +800.633.9876 +800.3987.6673 +800.7339.8766 +81.3.3511.7655 +81.3.3511.7656 FAX +400.883.1568 +971.4.2991800 +971.4.2991880 FAX +1.919.863.1794 +1.919.863.1797 FAX +31.33.453.4040 +31.33.453.4050 FAX +65.6383.4400 +65.6383.