User’s Guide P/2 DA4xi P/2 DA6xi VGA Distibution Amplifiers www.extron.com Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Description The P/2 DA4xi and P/2 DA6xi VGA-UXGA are high performance distribution amplifiers featuring one input/four outputs and one input/six outputs, respectively. Both P/2 DA units accept a VGA-UXGA video signal from a computer and distribute the signal to individually buffered outputs and one buffered loop-through. Each output is extendable up to 250' (76.2 m) with Extron’s VGA cables. Examples of typical installations are shown in the diagrams on the following pages.
P/2 DA4xi and P/2 DA6xi, cont’d b. Mount the unit on the rack shelf, as shown above, using two 4-40 x 3/16 screws in opposite (diagonal) corners to secure the case to the shelf. 6" Deep Rack Shelf 1/2 Rack Width Front False Faceplate VG Front false faceplate uses 2 screws. 4. Connect a monitor to the Local Monitor output of the distribution amplifier. 5. Connect LCD panels, VGA-UXGA monitors, or projectors to the other outputs as desired. 6. Connect power to the distribution amplifier. 7.
P/2 DA4xi and P/2 DA6xi, cont’d 1 Power LED: A green LED indicates that the distribution amplifier is receiving power. Rear panel features 5 3 4 INPUT (LOCAL MONITOR) P/2 DA6xi VG A 100-240V D IS TR IB 0.2A U 1 TI O N A M PL IF IE 5 4 6 R 3 VIDEO GAIN 1V P/2 DA6xi 2 .7V 3 OUTPUTS 50/60 Hz P/2 DA4xi 3. Hold the unit against the underside of the surface through which it will be mounted. Mark the four screw holes on the underside of the surface to which you are mounting the device.
P/2 DA4xi and P/2 DA6xi, cont’d To make input and output connections to other devices, do the following: 1. Turn off the PC and local monitor. 2. Connect the input cable of the P/2 distribution amplifier (DA) to the computer's VGA-UXGA output. If you wish to send RGBHV, RGBS, RGBsB, RsGsBs, component video, S-video, or composite video signals, use a standard SY breakout cable to make the connection. See the illustrations below.
P/2 DA4xi and P/2 DA6xi, cont’d Video Sync Gain ............................................... 0 dB or +3 dB (when input is 0.7 Vp-p, output is 0.7 V or 1.0 V, switchable) Bandwidth .................................... 300 MHz (-3 dB), fully loaded Video input Number/signal type ................... 1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, composite video Connectors .................................... (1) 15-pin HD female (optional Mac/VGA adapters are available) Nominal level ...
P/2 DA4xi and P/2 DA6xi, cont’d This page is intentionally left blank. 10 P/2 DA4xi/6xi • Installation This page is intentionally left blank.
P/2 DA4xi and P/2 DA6xi, cont’d This page is intentionally left blank.
