User Manual

ManualsBrandsExtron Electronics ManualsHardwareCable Cubby 700

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

Cable Cubby 500 and 700 • Installation Guide

This guide provides instructions for an experienced installer to install and connect the Extron

Cable Cubby 500 and 700 Cable Access Enclosures.

The Cable Cubby units are furniture-mounted enclosures for cable access,

connections, and AC power. Cables that are not in use can be stored out of the

way while remaining connected to the presentation system.

Cable Cubby 500 Cable Cubby 700

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Scr

ews

ii Bk

2 4

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

(3) 3/8", (1) 1/4" (6) 3/8", (2) 1/4"

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 trim, 2 screws 2 trims, 4 screws

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

1 2

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

4 8

Planning

Check with local and state regulations before starting

the installation:

 Ensure that the planned installation complies with building and electrical codes.

 Ensure that the planned installation complies with the Americans with Disabilities Act or

other accessibility requirements.

Check all parts and equipment before installation:

 Ensure that all parts are present in each kit.

 Ensure that necessary tools and equipment are available for the installation.

Kit Contents

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

Hole Plugs

Connectivity Bracket

Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500

Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX

TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

Summary of content (6 pages)

PAGE 1
e NT: RTA.com for thtion O P IM tron talla w.ex uide, ins ations. o ww Go t te user g specific nd ple com ctions, a u instr Cable Cubby 500 and 700 • Installation Guide This guide provides instructions for an experienced installer to install and connect the Extron Cable Cubby 500 and 700 Cable Access Enclosures. The Cable Cubby units are furniture-mounted enclosures for cable access, connections, and AC power.
PAGE 2
x.x" (x.x cm) x.x" (x.x cm) x.x" Cable Cubby 500 (Continued) x.x" and 700 • Installation Guide (x.x cm) (x.x cm) Preparing the Table Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut. Determine the bestx.x" location for the enclosure 30 (x.x cm) XL Models Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible. Ensure that the edge on which the lid opens is oriented correctly.
PAGE 3
Preparing the Cable Cubby Step 1 — Assemble the connectivity modules of your choice. Connectivity modules allow you to populate the Cable Cubby with a combination of AAPs, cable pass-through, or retractors. AAP Module 3 3 Secure the AAP plate on the connectivity brackets, using two of the provided module screws. Secure the AAP plate on the connectivity brackets, using two of the provided module screws. 1 1 Secure up to two single-space AAPs in the AAP plate.
PAGE 4
Step 2 — Install the modules. Determine where the connectivity modules and power module will be installed in the Cable Cubby. The modules may be installed on the left or right side of the enclosure and at various heights. NOTE: • Ensure that there is enough room above the modules for the Cable Cubby lid to close completely. • Use a screwdriver to secure the modules with the screws. L TA X TO A ~ 12 WARNING: Risk of Electric Shock.
PAGE 5
1 For cable pass-through applications, allow at least 36 inch of cable loop for each cable. Cable Cubby 500 and 700 • Installation Guide (Continued) Step 2 — Under the table, adjust the side clamps on the enclosure. 3 NOTE: To lower the side Ensure the Cable Cubby is firmly seated in the table. Raise the lever to secure the Cable Cubby. clamp, turn the lever down, then press and hold the locking plate while sliding down the clamp.
PAGE 6
Routing and Connecting Cables CAUTION: Risk of Electric Shock. This equipment must be grounded. 3 ATTENTION: Risque de choc électrique. Cet équipement doit être fixé au sol. Connect cables to the AV system and connect the AC power cord. NOTE: Ensure that there is no tension on the power cable. 2 Secure cables with zip ties to the rectangular holes in the rear of the Cable Cubby. e fit. 1 For cable pass-through applications, allow at least 36 inches (0.9 m) of cable loop for each cable.