User’s Manual CD 800 Quad-Standard Decoder EXTRON ELECTRONICS/RGB SYSTEMS, INC. 1230 South Lewis Street, Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 USA EXTRON ELECTRONICS, EUROPE Beeldschermweg 6C, 3821 AH Amersfoort +31.33.453.4040 FAX +31.33.453.4050 The Netherlands EXTRON ELECTRONICS, ASIA 41B Kreta Ayer Road, Singapore 089003 +65.226.0015 FAX +65.226.0019 Singapore EXTRON ELECTRONIC INFORMATION EXTRONWEB™: www.extron.com EXTRONFAX™: 714.491.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About This Manual ................................................................ 1-2 About the CD 800 .................................................................. 1-2 Features ...................................................................................... 1-2 Chapter 2 • Controls and Installation ............................ 2-1 Front and Rear Panels .....................................
Table of Contents, cont’d CD 800 1 Chapter One Introduction About This Manual About the CD 800 Features ii CD 800 Table of Contents
Introduction, cont’d Introduction About This Manual This manual contains information about the CD 800 quadstandard decoder and on how to operate and configure it. About the CD 800 The CD 800 is a high-resolution, quad-standard video decoder with a three-line adaptive comb filter. It converts NTSC, PAL, or SECAM standard interlaced S-video or composite video signals to non-interlaced RGBHV or RGBS video output.
Introduction, cont’d CD 800 2 Chapter Two Controls and Installation Front and Rear Panels Installation 1-4 CD 800 Introduction
Controls and cont’d Controls andInstallation, Installation Front and Rear Panels simultaneously and continuously as the control knob is rotated. Front panel features Rear panel features SECAM PAL 2 1 NTSC INPUT SELECTION NTSC 4.
Controls and Installation, cont’d 6 — H+ (positive H sync output polarity) On — Horizontal sync polarity is positive. See page 3-2 for information about the RS-232 port, and 3-6 for information about the remote contact closure control. Off — Horizontal sync polarity is negative. 7 — V+ (positive V sync output polarity) On — Sync polarity is positive. Off — Sync polarity is negative.
Controls and Installation, cont’d 3. Attach the CD 800 to the rack shelf with two 4-40 x 1/8” screws. Insert the screws from the underside of the shelf, and fasten them securely through opposite corners as shown in the illustration below. Cabling The CD accepts S-video and composite video input. You can connect one device of each type to the appropriate input, and you can connect one RGB display device to the output. You can also connect an RS-232 control device.
Controls and Installation, cont’d Cabling for video loopback CD 800 The CD 800 can be used with a system switcher in video loopback (VLB) mode. Details of this operation are included in Extron’s System 8/10 Plus switcher manual. The composite video, and/or the S-video outputs from the system switcher become the inputs for the CD 800. The RGB output from the CD 800 then connects to a special input on the system switcher. See the typical video loopback setup below.
3-2 CD 800 Remote Operation see “Error Responses” – next page Horiz. Phase Value + 1 Horiz. Phase Value – 1 Hph40 Hph39 Error response Exx {H }H Increment Hph value Decrement Hph value Hph Hph {H }H {^ }^ ^ H 7Bh48h 7Dh48h Contrast value to 99 Contrast value + 1 Contrast value – 1 Set H.
Remote Operation, cont’d Error responses If the CD 800 detects an error in a command, it returns one of the following error responses to the host.
Remote Operation, cont’d • From within the Signal Enhancement Products Control Program, press the F1 key. • From the Extron Electronics program folder or group, double-click on the Signal Enhancement Products Help icon. CD 800 Remote Contact Closure The RS-232/Remote connector provides a way to switch inputs on the CD 800 from a remote contact closure device. This is made possible through pins that are not used by the RS-232 interface. The contact closure pin assignments are shown below.
Specifications, cont’d Specifications Video input Control/Remote — decoder Number/type ............................... 1 S-video (Y/C), 1 composite video (switch-selectable) Connectors .................................... 1 4-pin mini-DIN female (S-video) 1 BNC female (composite video) Nominal level(s) .......................... Analog — 0.7V to 1V p-p Impedance .................................... 75 ohms Horizontal frequency ................. 15.6 kHz to 17.75 kHz Vertical frequency ....................
Specifications, cont’d A-4 CD 800 Specifications