User’s Manual CVEQ1, CVEQ1 WM, CVEQ1 AAP www.extron.com Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan 1230 South Lewis Street Anaheim, CA 92805 USA 714.491.1500 Fax 714.491.1517 Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050 135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.4664 Kyodo Building 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan +81.3.3511.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 这个符号警告用户该设备机壳内有暴 露的危险电压,有触电危险。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 避免追加 • 不要使用该产品厂商没有推荐的工具或 追加设备,以避免危险。 警告 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 (地线)是安全设施,不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后 或桌面电源的电源线,或任何接到市电系统的电源线。 电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。 维护 • 所有维修必须由认证的维修人员进行。 设备内部没 有用户可以更换的零件。为避免出现触电危险不要自己 试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 •
Precautions, continued Quick Start Guide — CVEQ1 Series CAUTION Installation and service must be performed by authorized personnel only. The CVEQ1 AAP and CVEQ1 WM must be used with UL approved electrical boxes. See “UL Requirements”, page 2-3. To install and set up a CVEQ1, follow these steps: Step 1 Turn the input and output devices off and unplug their power cords. Step 2 For the CVEQ1, go to step 3. For the CVEQ1 AAP, A. Determine the installation location. B.
Quick Start Guide — CVEQ1 Series, cont’d Step 7 While watching the display, adjust the video gain and equalization by using the rotary Gain and Equalize controls. An oscilloscope can be used to achieve a more precise adjustment. See “Top/Side Panel Features and Adjustments” in chapter 2. Step 8 For the CVEQ1 AAP or CVEQ1 WM, A. Disconnect the line driver’s power supply at the source end (not at the line driver). B. Disconnect the input and output devices’ power. C.
Table of Contents, cont’d CVEQ1, CVEQ1 WM, CVEQ1 AAP 1 Chapter One Introduction About the CVEQ1, CVEQ1 WM, and CVEQ1 AAP Features vi CVEQ1 Series • Table of Contents
Introduction About the CVEQ1, CVEQ1 WM, and CVEQ1 AAP The Extron CVEQ1 is a one-input, one-output, composite video line driver. It features a 185 MHz (-3 dB) video bandwidth. It accepts one composite video input on a female BNC connector and one stereo audio input on a pair of female RCA connectors. One female BNC connector provides equalized video output, and a five-pole captive screw connector provides for stereo audio output.
Installation, Setup, Operation Connecting Shields.eps UL Requirements The Underwriters Laboratories (UL) requirements listed below pertain to the installation of the CVEQ1 WM and CVEQ1 AAP. 1. 5. Feed cables through the wall box punch-out holes, and secure them with cable clamps to provide strain relief. 6. Exposed cable shields (braids or foil) are potential sources of short circuits. Trim back and/or insulate shields with heat shrink.
Installation, Setup, Operation, cont’d If attaching the wall box to wood, use four #8 or #10 screws or 10-penny nails. A minimum of ½ inch (1.3 cm) of screw threads must penetrate the wood. If attaching the wall box to metal studs or furniture, use four #8 or #10 self-tapping sheet metal screws or machine bolts with matching nuts. 8.
Installation, Setup, Operation, cont’d Rear/Bottom/Side Panel Features and Cabling 2 Video output connector — Using a coaxial cable, connect a display device to this female BNC connector. For the CVEQ1 WM and CVEQ1 AAP, the BNC is at the end of a short pigtail on the circuit board. 3 Power supply connection — On the CVEQ1 the power input connector is a 2-pole jack that can be used to connect a 9 VDC Power Connector wiring_compact.eps to 24 VDC, 1 A (maximum), external power supply.
Installation, Setup, Operation, cont’d adjustment changes the level and peaking of the output signal to compensate for capacitance caused by up to 1000 feet (300 meters) of Extron RG6 cable. Top/Side Panel Features and Adjustments 1 GAIN 2 1 2 Use a small, flat-blade screwdriver to rotate this control. View the display and select the setting that gives the sharpest picture.
Installation, Setup, Operation, cont’d CVEQ1 WM Install.eps Mounting the CVEQ1 AAP Mounting the CVEQ1 WM The CVEQ1 AAP and any other adapter plates must be attached to a device’s faceplate or an AAP wallplate and cabled before the device or wallplate is installed in a wall or furniture. The screws needed for installing the CVEQ1 AAP are built into its front panel, so no additional screws are needed. 1. CVEQ1AAP’s AAP screws w RGB 568 installation.
Installation, Setup, Operation, cont’d CVEQ1, CVEQ1 WM, CVEQ1 AAP A Appendix A Specifications, Part Numbers, and Accessories Specifications Included Parts Accessories Cables 2-12 CVEQ1 Series • Installation, Setup, Operation
Specifications, Part Numbers, Accessories Specifications Audio output Video Gain ................................................... -6 dB to +6 dB, adjustable: 0.5 V to 2.0 V ±10% with input at 1 volt Equalization/peaking gain ........... 4.5 dB max. @ 8 MHz Bandwidth ....................................... 185 MHz (-3 dB) Differential phase error .................. 1º at 3.58 MHz Differential gain error ..................... 0.07% at 3.58 MHz Video input Number/signal type .......................
Specifications, Parts, and Accessories, cont’d Warranty ........................................... 3 years parts and labor CVEQ1, CVEQ1 WM, CVEQ1 AAP All nominal levels are at ±10%. Specifications are subject to change without notice. Included Parts These items are included in each order for a CVEQ1, CVEQ1 AAP, or CVEQ1 WM: Included parts Part number CVEQ1 60-360-02 or CVEQ1 AAP (gray, black, white) 70-146-02, -12, -22 or CVEQ1 WM (gray, black, white) 60-435-02, -12, -22 12 VDC, 1 A max.
Dimensions and Templates Dimensions Template The dimensions drawing is not 100% of the actual size. CVEQ1 WM template Cut-Out Template for the Extron ø 0.156 THRU WITH ø 0.290 X 82° C'SINK (2 PLACES) CVEQ1 WM 2.790 1.465 1.395 0.000 ø 0.120 THRU 2.79" (8.0 cm) 0.100 4.500 3.890 3.700 R 0.060 (TYP) 3.410 3.160 ø 0.530 THRU VIDEO IN 2.720 L AUDIO IN 2.024 R AUDIO IN 1.433 ø 0.440 THRU (2 PLACES) C'BORE 2.900 x 1.400 x 0.050 DEEP (FAR SIDE) 2.24" (105 cm) 4.50" (16.5 cm) 4.
Dimensions, Templates, cont’d B-4 CVEQ1 Series • Dimensions, Templates