Owner's manual
DA RGB/YUV Distribution Amplifiers • Installation and Operation
DA RGB/YUV Distribution Amplifiers • Installation and Operation
Installation and Operation, cont’d
2-52-4
Rack mounting the DA4 and DA6
1. Attach the rack mount brackets to the DA with the eight
provided #8 machine screws (figure 2-2).
#8 Screw (4 Plcs)
Each Side
Mounting Screws (2 Plcs)
Each Side
Rack-mount
Bracket
Table/
Wall-mount
Bracket
Drill pilot holes
3/32” (2.4 mm) diam
1/4” (6.3 mm) deep
or
I
N
P
U
T
Y
D
IG
ITA
L
A
UD
IO
R
-Y
B
-Y
1
0
0
-
2
4
0
V
1
.
3
A
5
0
-
6
0
H
z
D
A
6
Y
U
V
A
O
U
T
P
U
T
1
O
U
T
P
U
T
2
D
IG
IT
AL
A
U
D
IO
D
IG
ITA
L
A
U
DIO
Y
R-Y
B
-Y
Y
R
-Y
B-Y
D
IG
ITA
L
A
U
D
IO
DIG
ITA
L
A
UD
IO
Y
R
-Y
B
-Y
Y
R
-Y
B-Y
O
U
T
P
U
T
3
O
U
T
P
U
T
4
DIG
ITA
L
A
U
D
IO
D
IG
ITA
L
AU
D
IO
Y
R
-Y
B
-Y
Y
R-Y
B-Y
O
U
T
P
U
T
5
O
U
T
P
U
T
6
A
C
/D
C
S
PA
R
E
O
N
Figure 2-2 — Rack mounting a DA4 or DA6
2. Insert the DA into the rack, aligning the holes in the
mounting bracket with those of the rack.
3. Secure the DA to the rack using the supplied machine
screws.
Under-furniture mounting the DA
The DAs can be mounted under a table or other horizontal
surface. The DA2 RGBHV requires an optional Extron MBU 125
under-desk mounting kit (part #70-077-01). The DA4 and DA6
models require the included table/wall mount bracket. Mount
the DA under a desk or table as follows:
1. Secure the under-desk mounting brackets to the DA with
the four (DA2) or eight (DA 4 and DA6) machine screws
provided in the mounting kit (figure 2-2 for the DA4 and
DA 6 or figure 2-3 for the DA 2).
2. Hold the DA with attached brackets against the underside
of the desk or other furniture. Mark the location of holes
for screws on the desk.
D
A
R
G
B
/
Y
U
V
S
E
R
I
E
S
W
I
D
E
B
A
N
D
D
IS
T
R
IB
U
T
IO
N
A
M
P
L
IF
IE
R
Figure 2-3 — Under-furniture mounting
3. Drill 1/4" (6.4 mm) deep, 3/32" (2 mm) diameter pilot
holes in the table or desk at the marked screw locations
from the underside or inside (the concealed side) of the
furniture, where the DA will be located.
4. Insert the four wood screws into the pilot holes. Fasten
each screw into the installation surface until just less than
1/4" of the screw head protrudes.
5. Align the installed screws with the slots in the mounting
brackets, and place the DA against the surface, with the
screws through the bracket slots.
6. Slide the DA slightly forward or back, then tighten all four
screws to fasten it in place.