DAT104 1–INPUT, 4–OUTPUT DFP / DVI DISTRIBUTION AMPLIFIER DAT104 OPERATION MANUAL
Installation and Safety Instructions For Models without a Power Switch: The socket outlet shall be installed near the equipment and shall be accessible. For all Models: No serviceable parts inside the unit. Refer service to a qualified technician. For Models with Internal or External Fuses: For continued protection against fire hazard, replace only with same type and rating of fuse.
1 Product Overview The DAT104 is a high-resolution video distribution amplifier designed to split and buffer the digital signals from a single computer graphics card to four flat panel displays, plasma monitors, LCD projectors or other display devices that feature DFP or DVI digital video inputs. The DAT104 features DFP (Digital Flat Panel) connectors for input and outputs, allowing for direct connection to digital video sources and displays.
2 Compatibility INPUT The DAT104 will accept a single link TMDS signals with at resolutions up to 1280 x 1024 (SXGA). The unit accepts the signal on a 20-pin DFP connector. The DAT104 will also accept single link TMDS based signals from DVI ports when used with the appropriate video adapter cable (see the list on page 6). OUTPUT Featuring four (4) independently buffered DFP (MDR20) video output ports, the DAT104 can drive up to four display devices simultaneously.
3 Installation This section offers step-by-step instructions for installing the DAT104 distribution amplifier. An Application Diagram is provided on the following page. Note: Read the instructions carefully before initiating the installation procedure. Make sure there is no power connected to the DAT104 and all power switches are in the OFF position. 1. Place / Install the DAT104 - at the desired location.
DAT104 Operation Manual - V1.0 12/1/00 4 © 2000 - INLINE, Inc.
5 Specifications DAT 104 Distribution Amplifier Input Connector Type Signals Compatible Signals Input Impedance Output Buffered Local Display Main Output Output Format EDID Data Bandwidth General Power Supply Dimensions Product Weight Shipping Weight Regulatory Approvals (1) MDR20 female connector Single link TMDS digital video signals Resolution up to 1280 x 1040 100 ohms differential (1) MDR20 female connector (3) MDR20 female connectors Single link T.M.D.S.
6 INLINE Digital Video Cables and Adapters Accessories for DAT104 IN9700 High Performance Digital Video Cables - Use for Cable Runs from 25’ to 75’ IN9725-1: IN9735-1: IN9750-1: IN9775-1: DFP Male to DFP Male, 25’ DFP Male to DFP Male, 35’ DFP Male to DFP Male, 50’ DFP Male to DFP Male, 75’ IN9725-2: IN9735-2: IN9750-2: IN9775-2: DFP Male to DVI Male, 25’ DFP Male to DVI Male, 35’ DFP Male to DVI Male, 50’ DFP Male to DVI Male, 75’ IN9725-3: IN9735-3: IN9750-3: IN9775-3: DVI Male to DVI Male, 25’ DVI
7 Troubleshooting Problem: There is no image on any of the display devices. Solution 1: Make sure that the IN9230 IEC power cable is securely plugged into the DAT104 and the A/C source. Solution 2: Make sure the A/C source is live. Solution 3: Verify that the power switch is turned on for the video source and all display devices. Solution 4: Verify the connections to all the output display devices. Solution 5: Verify that OUTPUT 1 (local display) is connected to a display device.
8 Warranty ♦ INLINE warrants the equipment it manufactures to be free from defects in materials and workmanship. ♦ If equipment fails because of such defects and INLINE is notified within two (2) years from the date of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications.