User’s Manual www.extron.com Extron Electronics, USA 1230 South Lewis Street Anaheim, CA 92805 800.633.9876 714.491.1500 FAX 714.491.1517 Extron Electronics, Europe Beeldschermweg 6C 3821 AH Amersfoort, The Netherlands +800.3987.6673 +31.33.453.4040 FAX +31.33.453.4050 Extron Electronics, Asia 135 Joo Seng Rd. #04-01 PM Industrial Bldg., Singapore 368363 +800.7339.8766 +65.6383.4400 FAX +65.6383.4664 © 2008 Extron Electronics. All rights reserved.
Precautions Safety Instructions • English This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. Caution Read Instructions • Read and understand all safety and operating instructions before using the equipment.
安全须知 • 中文 警告 这个符号提示用户该设备用户手册中 有重要的操作和维护说明。 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 必须使用有地线的供电系统供电。 第三条线 (地线)是安全设施,不能不用或跳过。 这个符号警告用户该设备机壳内有暴 拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后 或桌面电源的电源线,或任何接到市电系统的电源线。 露的危险电压,有触电危险。 电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。 注意 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 解所有安全和使用说明。 保存说明书 • 用户应保存安全说明书以备将来使 用。 遵守警告 • 用户应遵守产品和用户指南上的所有安 全和操作说明。 维护 • 所有维修必须由认证的维修人员进行。 设备内部没 有用户可以更换的零件。为避免出现触电危险不要自己 试图打开设备盖子维修该设备。 通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止 机内敏感元件过热。 不要用任何东西挡住通风孔。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与 厂家推荐的相同
Table of Contents Chapter One • Introduction ..................................................... 1-1 About this Manual ..................................................................... 1-2 About the DVI DL 101 Cable Equalizer ................................ 1-2 Features ......................................................................................... 1-2 Application Diagrams . .............................................................. 1-3 Chapter Two • Installation and Operation . ......
Table of Contents, cont’d DVI DL 101 1 Chapter One Introduction About this Manual About the DVI DL 101 Cable Equalizer Features Application Diagram ii DVI DL 101 • Table of Contents
Introduction About this Manual This manual contains information about the Extron DVI DL 101 Dual Link Cable Equalizer and describes how to connect and operate it. The terms "DVI DL" and "equalizer" are used interchangeably throughout this manual to refer to the product. About the DVI DL 101 Cable Equalizer The Extron DVI DL 101 is a dual link cable equalizer that extends Digital Visual Interface (DVI) signals beyond the specified cable limits of 15' (5 m).
Introduction, cont’d DVI DL 101 2 Chapter Two Installation and Operation Mounting the DVI DL 101 Front and Back Panel Features and Connections Enabling the DDC Buffer 1-4 DVI DL 101 • Introduction
Installation and Operation Mounting the DVI DL 101 5. The DVI DL can be mounted on a rack shelf, under or through furniture, attached to a projector pole, or placed on a table top. Tabletop use Four self-adhesive rubber feet are included with the DVI DL. For tabletop use, attach one foot at each corner on the bottom surface of the unit. Rack mounting The optional accessories available for rack mounting the DVI DL include the following: • RSF 123 — 3.
Installation and Operation, cont’d VersaTools Rack Shelf 1/4 Rack Width Front False Faceplate Use 2 mounting holes on opposite corners. (2) 4-40 x 3/16" Screws Mounting the DVI DL 101 on a 3.5” deep rack shelf Under-furniture mounting The DVI DL can be mounted under a horizontal surface using an optional MBU 125 under-desk mounting kit (part #70-077-01), as follows: 2-4 1. If rubber feet were previously attached to the bottom of the unit, remove them. 2.
Installation and Operation, cont’d PMK 300 mounting Mount the DVI DL to a PMK 300 bracket as follows: 1. If necessary, remove the feet from the bottom of the unit. 2. Mount the receiver to one of the bracket’s three mounting plates using two of the supplied 4-40 x 3/16" screws in opposite (diagonal) corners to secure the device to the bracket. It can be vertically mounted facing either up or down (see the illustration below).
Installation and Operation, cont’d 6. Contoured Bracket Base PMK 350 mounting Mount the DVI DL to a PMK 350 bracket as follows: Extron DVI DL 101 Equalizer 1. Remove the front and rear plates from the PMK 350, using an Extron Tweeker or a #2 Philips screwdriver. Retain the screws to reattach the plates when you are finished. 2. If necessary, remove the feet from the bottom of the unit. 3.
Installation and Operation, cont’d Assemble the U-bolt and the following parts in the following order (see the illustration below): 7. Front and Back Panel Features and Connections 2 a. Pass the legs of the U-bolt through the slotted holes on the mount plate flange. b. Place the legs around the projector pole. DVI-DUAL LINK INPUT 1 c. Pass the legs through the holes in the contour base. N The pole fits snugly into the depression in the center of the contoured base. DVI DL 101 d.
Installation and Operation, cont’d 9 Pin Signal Pin 1 TMDS data 2– 9 1 8 17 24 The table below shows the maximum cable lengths recommended for each resolution, in dual link mode and single link mode.
Installation and Operation, cont’d • Incorrect color space selection (purple or blue tint) • Corrupted EDID data (The computer or source cannot read the EDID of the connected display correctly due to a long cable run.) Ridges Smooth A A To enable the buffer, SECTION A–A Power Supply Output Cord 1. Using an Extron Tweeker or other small Philips screwdriver, remove the seven screws (three on each side and one on top) that hold the top cover onto the unit. 2.
Installation and Operation, cont’d 5. Lift each jumper off its pins and slide it down onto the inside and middle pins. See the illustration below. DDC Buffer Bypassed (Default) DDC Buffer Enabled Jumper Pin Sets J4 and J5 Inside Unit NK L LI UA T PU IN 01 L1 ID DV -D DVI Remove screws from sides and top (7). Slide forward, then up. Jack Screw Nut 6. Replace the top cover onto the unit, and slide it back until the DVI input connector protrudes through its slot in the front panel. 7.
Specifications, Parts, and Accessories Specifications – DVI DL N *Dual link DVI is backwards compatible with all single link DVI and HDMI signals. Video Maximum data rate ���������������������� Maximum pixel clock ������������������� Impedance �������������������������������������� Resolution range ��������������������������� 10 Gbps total (3.
Specifications, Parts, and Accessories, cont’d Included Parts Cables and Adapters These items are included in each order for the DVI DL 101: Replacement part number Included parts DVI DL 101 Multi-Rate Equalizer 60-962-01 12 VDC, 2 A external power supply kit 70-055-01 IEC power cord Rubber feet, 4, unattached Tweeker (small screwdriver) DVI DL 101 User’s Manual Optional Accessories The following items are optional and can be purchased separately for the DVI DL 101: Accessories Part number MBD 129
Specifications, Parts, and Accessories, cont’d This page was intentionally left blank.