User Guide User Manual

ManualsBrandsExtron Electronics ManualsAccessories communicationDVI 104 TX_RX

IMPORTANT:

Go to www.extron.com for the

complete user guide, installation

instructions, and specifications.

DVI 104 TX/RX • User Guide

The Extron DVI 104 Tx and DVI 104 Rx are ﬁber optic transmitter and receiver units that extend DVI signals up to 500 meters

(1,640 feet) using four multimode ﬁber optic cables. Optional four-ﬁber multimode cables are available in varying lengths.

• The transmitter plugs directly into the source device and the receiver plugs directly into the display device.

• The transmitter and receiver pair can handle DVI video signals with resolutions up to 1920 x 1200 or 1080p at 60 Hz.

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC

rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

NOTE: This unit was tested with shielded I/O cables on the peripheral devices. Shielded cables must be used to ensure

compliance with FCC emissions limits.

For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see

the “Extron Safety and Regulatory Compliance Guide” on the Extron website.

FDA/IEC 60825-1 Requirements

CLASS 1 LASER PRODUCT

Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 5, dated June 24,

2007.

The product is intended to be used with the ﬁber optic cables fully installed.

This product meets the applicable requirements of IEC 60825-1, Edition 1 (2007).

Any service to this product must be carried out by Extron Electronics and its qualiﬁed service personnel.

Application Diagram

PC with DVI Output

DVI 104

Transmitter

DVI 104

Receiver

Hi-resolution

Flat Panel Display

with DVI-D Input

4 Multi Mode

Fiber

Up to 500 meters (1640 feet)

Summary of content (5 pages)

PAGE 1
DVI 104 TX/RX • User Guide The Extron DVI 104 Tx and DVI 104 Rx are fiber optic transmitter and receiver units that extend DVI signals up to 500 meters (1,640 feet) using four multimode fiber optic cables. Optional four-fiber multimode cables are available in varying lengths. • The transmitter plugs directly into the source device and the receiver plugs directly into the display device. • The transmitter and receiver pair can handle DVI video signals with resolutions up to 1920 x 1200 or 1080p at 60 Hz.
PAGE 2
DVI 104 TX/RX • User Guide Features Power supply — Separate power supplies are provided for both the transmitter and receiver. Power LEDs — The LEDs are on the top and bottom panels of both the receiver and transmitter. They illuminate green when the unit is receiving power. No mounting hardware required — The units plug directly into the source device (transmitter) or output device (receiver) and take up very little space.
PAGE 3
DVI 104 TX/RX • User Guide Rear Panel Features 1 3 6 c 8 3 Male Connector 9 17 19 A single-link DVI-D male connector is used to connect the transmitter to the source and the receiver to the output device.
PAGE 4
DVI 104 TX/RX • User Guide 3. Press and release the EDID Minder programming button by gently inserting a pointed device, such as a paper clip, into the recess on the side of the transmitter. The green LED should blink twice and turn off, although power is still connected. The transmitter is ready to capture EDID information from the display device. 4. Power on the display device. 5. Connect the transmitter directly to the DVI input of the display device.
PAGE 5
DVI 104 TX/RX • User Guide Troubleshooting Display does not show an image • Ensure that all plugs and jacks used by the external power supplies are firmly connected. Locking catch If the cable is loose or slips out of the slot easily, move the release catch from its normal position above the locking catch, to the adjusted position under the locking catch (see the figure at right). This provides the extra leverage required to keep the locking catch in place and hold the cable securely.