Setup Guide User guide

4
68-2290-50
Rev. B
06 13
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: [phone]
Extron USA - East: +1.919.850.1000 FAX: [phone]
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Command ASCII Command
(Host to Device)
Response
(Device to Host)
Additional Description
Select audio and video input
X!! InX!
•
All] Selects audio and video input X!.
Select video input only
X!& InX!
•
RGB] Selects the video only input X!.
Select audio input only
X!$ InX!
•
Aud] Selects the audio only input X!.
Execute Auto-Image
A
Img0
]
Executes Auto-Image on the current input.
Execute Auto-Image and ll
1*A
Img1
]
Executes Auto-Image and lls the output.
Execute Auto-Image and follow
2*A
Img2
]
Executes Auto-Image and maintains the aspect ratio of
the current input.
Set scaler output rate
EX5$ RATE} RateX5$]
Species an output resolution and refresh rate.
Mute video to black
1B
Vmt1
]
Mutes the video and displays a black output.
Mute video and sync
2B
Vmt2
]
Mutes the video and sync output.
Unmute video and sync
0B
Vmt0
]
Unmutes the video.
NOTE: By default, adjusting variable volume with the following commands only affects variable analog output (see the IN1606 and IN1608
Series User guide to configure the variable volume through group masters).
Set variable volume level
ED8*X4$ GRPM} GrpmD08*X4$]
Set the variable volume to a value of X4$.
Raise variable volume
ED8*X4* +GRPM}
GrpmD08*X4$]
Increase the level of the variable volume by X4* dB.
Lower variable volume
ED8*X4* -GRPM}
GrpmD08*X4$]
Decrease the level of the variable volume by X4* dB.
View variable volume level
ED8GRPM} X4$]
View the current variable volume level.
NOTE: By default, setting the audio mute with the following commands affects all outputs (see the IN1606 and IN1608 Series User guide to
configure the master audio mute through group masters).
Set master audio mute
ED7*X( GRPM} GrpmD07*X(]
Enable or disable master audio mute.
View master audio mute status
ED7GRPM} X(]
View the current master audio mute status.
Enable executive mode 1
1X
Exe1
]
Locks out the entire front panel.
Enable executive mode 2
2X
Exe2
]
Locks the front panel except for input selection and
volume control.
Disable executive modes
0X
Exe0
]
Allows all front panel adjustments and selections.
Set screen saver mode
EMX2& SSAV} SsavM X2&]
Set the screen saver mode.
Set screen saver time-out duration
ETX2# SSAV} SsavTX2#]
Set the screen saver sync time-out duration.
View screen saver status
ESSSAV} X3*]
View the status of the screen saver.
Set scaler IP address
EX4) CI} Ipi
•
X4)]
Species a new scaler IP address.
Set scaler DHCP mode
EX( DH} IdhX(]
Enables or disables DHCP.
Set subnet mask
EX4! CS} Ips
•
X4!]
Species a new subnet mask.
Set gateway IP address
EX4@ CG} Ipg
•
X4@]
Species a new gateway IP address.
Reboot networking
E2BOOT} Boot2]
Restarts the network after IP or DHCP changes.
NOTE: IP settings will not take effect until the E2BOOT} command is executed.
NOTES:
X! = Input selection (1-6)
X( = Enable or disable (0 = off or disabled; 1 = on or enabled)
X2# = Screen saver sync time-out duration (0 = instant time out; 1-500 = in 1 second increments; 501 = never)
X2& = Screen saver mode (1 = black output [default]; 2 = blue output)
X3* = Screen saver status (0 = active input detected; 1 = no active input, timer running; 2 = no active input, timer expired, output disabled)
X4) = IP address (xxx.xxx.xxx.xxx; 192.168.254.254 = default)
X4! = Subnet mask (xxx.xxx.xxx.xxx; 255.255.0.0 = default)
X4@ = Gateway address (xxx.xxx.xxx.xxx; 0.0.0.0 = default)
X4$ = Group volume level (-1000 to 0, where -1000 = -100 dB or 0% volume and 0 = 0 dB or 100% volume)
X4* = Increment value (dB value multiplied by ten, in 0.1 dB increments, to raise or lower a group fader [for example, 100 = 10 dB])
X5$ = Output rate (see the table on page 3 or the IN1606 and IN1608 Series User Guide)