Installation Owner manual

ManualsBrandsExtron Electronics ManualsHardwareTeamWork 601i Kits

TeamWork

601 and 601i Kits • Installation Guide

TeamWork 601 and 601i Kits

The TeamWork 601 and TeamWork 601i kits consist of an analog and digital video switcher, system controller, Cable Cubby

, and

cables packaged together as a complete system that, in most cases, requires no conguration.

0.5A M

POWER

12V

INPUTS

MPS 601

CONTACT IN / TALLY OUT

HDMI

RGBHV

HDMI

RS-232

1 3 5

2 4 6

T T

C G TC G

C T TC

G T

C G

Tx Rx G

OUTPUT

REMOTE

Extron

100-120V 50/60Hz

12A MAX POWER OU

TPUT 12A MAX

LAN

COM

IN S G

+5VRX

INPU

LIS

TED

7TT

DIO/

RATUS

Extron

Cable Cubby 1400

Cable Access Enclosure

Regional Sa

les

120

150

SOUTH

NORTH

EAST

WEST

Extron

MPS 601

Switcher

Extron

IPL T PC1

System Controller

RS-232

Control Cable

HDMI

VGA

Extron

HDMI Pro Cable

HDMI Video

Flat Panel

Display w/ Integrated

Speakers

Extron “Show Me” Cables

Flat Panel

AC Cord

CUBBY

Contact Closure

& Tally

Regional Sales

120

150

SOUTH

NORTH

EAST

WEST

The diagram above shows a typical TeamWork 601 application. Digital or Analog input devices (laptops and a tablet) connect to

the switcher, using “Show Me” cables. Analog video is digitized to HDMI output. The “Show Me” cables allow the user to select

the active input on the switcher.

A control cable connects the RS-232 ports on the switcher and the system controller.

The system controller powers the display on and off. The system controller has been congured so that when a video signal is

detected on any of the switcher inputs, the display is powered on. A 30 second timer is started when no signal is detected on any

of the switcher inputs. If an active source is detected before the timer expires, the display remains on and the timer is reset. If 30

seconds pass without an active signal, the system controller powers off the display.

The TeamWork kits work, as described, without further software conguration. If you need to change the behavior or operation of

the system, you must congure the system controller (see the IPL T PC1/IPL T PC1i User Guide at www.extron.com).

Summary of content (10 pages)

PAGE 1
TeamWork® 601 and 601i Kits • Installation Guide TeamWork 601 and 601i Kits The TeamWork 601 and TeamWork 601i kits consist of an analog and digital video switcher, system controller, Cable Cubby®, and cables packaged together as a complete system that, in most cases, requires no configuration.
PAGE 2
TeamWork Kits • Installation Guide (Continued) TeamWork 601 and TeamWork 601i Kits Included Parts TeamWork 601 TeamWork 601i Video switcher 1 (MPS 601) 2 VGA and 4 HDMI inputs 1 (MPS 601) 2 VGA and 4 HDMI inputs System controller 1 (IPL T PC1) 1 (IPL T PC1i) Cable Cubby 1400 1 1 Power modules 2 US modules included (4 AC outlets total) Sold separately HDMI “Show Me” cables 4 4 VGA “Show Me” cables 2 2 HDMI cable 1 1 Switcher control cable 1 1 IEC C14 male power cord plug (see instru
PAGE 3
Display Requirements The TeamWork system is designed to work with most brands and models of flat panel displays available worldwide. For optimum performance, consider the following when selecting the displays for your TeamWork installation. The display should be tested thoroughly prior to installation or mass deployment of TeamWork systems. Power attributes — The system works by controlling AC power to the display.
PAGE 4
TeamWork Kits • Installation Guide (Continued) Installation Detailed instructions are in the Cable Cubby Installation Guide. Cable Pass-through Modules (2) Power Modules (2) 240V ~ 50-60Hz 10A MAX TOTAL Cable Pass-through Modules (2) Power Modules (2) Install the AC Power Modules in the Cable Cubby 125V ~ 50-60Hz 12A MAX TOTAL Extron recommends the layout shown to the right with the two power modules diagonally opposite each other and the cable pass-through modules diagonally opposite each other.
PAGE 5
Mounting and Placement of System Components Decide where you will install your TeamWork system and where the individual components will be placed. zz The Cable Cubby should provide easy access for as many users as possible. Ensure that there is ample space for cables under the table. Ensure that the edge on which the lid opens is correctly oriented. zz The system controller should be placed close to the display. zz The MPS 601 switcher should be placed close to the Cable Cubby.
PAGE 6
TeamWork Kits • Installation Guide (Continued) Cabling US ® 17TT ED LIST IDEO IO/V AUD ATUS APAR M CO +5V N LA RX TX IR UT INP Hz 5 Contact Closure & Tally T U TP OU TS PU IN MI HD +V T TE G MO C 5 RE 32 T -2 T G RS C 3 Y OU LL T 6 G / TA G C 1 T IN Rx AC 4 Tx NT CO T G 2 C T G C T G C MI 6 3 1 S 60 Extron MPS 601 Switcher G IN A MA UT X 12 TP R OU WE PO Extron IPL T PC1 X 12 A MA 6 System Controller Flat Panel AC Cord RS-232 Control Cable 4 s gio HDMI Video HD
PAGE 7
“Show Me” Cables The Extron “Show Me” cables are for use with Extron TeamWork systems. They feature a Share button for remote input source selection and a control pigtail, which may be wired directly into Extron switchers with contact closure and tally outputs.
PAGE 8
TeamWork Kits • Installation Guide (Continued) Connect the Switcher to the Display Device Connect the switcher HDMI output to the HDMI input of the display device, using the provided cable. Do not use HDMI to DVI adapters. If necessary, see the user guide for the display device. Connect the Display to the System Controller Connect the power cord from the display device to the power output receptacle of the system controller. TeamWork systems work by controlling the AC power to the display.
PAGE 9
Testing the System The TeamWork system has been pre-configured so that, once all the connections have been made and the devices are all powered on, there should be no need of further configuration for the system to work. To ensure that the system has been set up correctly, follow these steps: 1. 2. 3. Power on the equipment zz Source devices zz Switcher zz System controller (IPL T PC1) Press the power button (1) on the front panel of the system controller.
PAGE 10
TeamWork Kits • Installation Guide (Continued) “Show Me” Button LEDs Stay Off When Pressed: Cause 1 — The cable is not plugged into a source device that is producing an active video output signal: Solution — Verify that the source device is on and producing an active signal. Cause 2 — Contact or Tally wiring is incorrect: Solution — See “Show Me” Cables (page 7) to ensure the contact and tally pins are correctly wired.