Installation Owner's manual

ManualsBrandsExtron Electronics ManualsHardwareTeamWork

TeamWork

• Installation Guide

TeamWork

Extron TeamWork is a fully customizable collaboration system comprised of an Extron switcher, “Show Me” cables, a control

processor, and a Cable Cubby

enclosure. This installation guide provides the information needed for an experienced installer to

set up these systems.

ATTENTION:

• The information in this guide refers to a typical TeamWork system. The devices provided in your kit may differ from those

shown in the illustrations.

• If your system uses a different IPLcontroller, switcher, or Cable Cubby from the ones shown in this guide consult the user

guide for your model before connecting or conguring that device. The user guides are available on line at

www.extron.com.

In a typical TeamWork application, shown below, digital or analog input devices (laptops and a tablet) connect to the switcher,

using “Show Me” cables. The “Show Me” cables allow the user to select the input on the switcher.

0.5A M

POWER

12V

INPUTS

MPS 601

CONTACT IN / TALLY OUT

HDMI

RGBHV

HDMI

RS-232

1 3 5

2 4 6

T T

C G TC G

C T TC

G T

C G

Tx Rx G

OUTPUT

REMOTE

Extron

100-120V 50/60Hz

12A MAX POWER OUTPUT 12A MAX

LAN

COM

IN S G

+5VRX

INPU

LIS

TED

7TT

DIO/

RATUS

Extron

Cable Cubby 800

Cable Access Enclosure

00-240

00-240V

240V/

5A MA

Regional Sa

les

120

150

SOUTH

NORTH

EAST

WEST

Extron

MPS 601

Switcher

Extron

IPL T PC1

System Controller

RS-232

Control Cable

HDMI

VGA

Extron

HDMI Pro Cable

HDMI Video

Flat Panel

Display w/ Integrated

Speakers

Extron “Show Me” Cables

Flat Panel

AC Cord

Contact Closure

& Tally

Regional Sales

120

150

SOUTH

NORTH

EAST

WEST

HDMI

VGA

Summary of content (8 pages)

PAGE 1
TeamWork® • Installation Guide TeamWork Extron TeamWork is a fully customizable collaboration system comprised of an Extron switcher, “Show Me” cables, a control processor, and a Cable Cubby® enclosure. This installation guide provides the information needed for an experienced installer to set up these systems. ATTENTION: • The information in this guide refers to a typical TeamWork system. The devices provided in your kit may differ from those shown in the illustrations.
PAGE 2
TeamWork • Installation Guide (Continued) Mounting and Installation Assembling the Cable Cubby 1. Install the power modules in the Cable Cubby. The power modules that you use depend on the country you are in and the Cable Cubby model that you are using. For complete installation instructions for your Cable Cubby, see the installation guide for that Cable Cubby, which is available at www.extron.com.
PAGE 3
Mounting and Placement of System Components Decide where you will install your TeamWork system and where the individual components will be placed. zz The Cable Cubby should provide easy access for as many users as possible. Ensure that there is ample space for cables under the table. Ensure that the edge on which the lid opens is correctly oriented. zz The system controller should be placed close to the display. zz The switcher should be placed close to the Cable Cubby.
PAGE 4
TeamWork • Installation Guide (Continued) Cabling US ® 17TT ED LIST IDEO IO/V AUD ATUS APAR M CO +5V N LA RX TX IR UT 5 INP Hz /60 V 0-1 50 S 20 G IN 10 A MA UT X 12 TP R OU WE PO Extron IPL T PC1 Contact Closure & Tally 12 A MA X 6 Flat Panel AC Cord System Controller RS-232 Control Cable 4 +V G C 5 UT TP OU TS PU MI HD IN T T T G C 3 Y OU LL T 6 G / TA C 1 T IN AC 4 NT CO T G 2 C T G C T G C TE MO RE 32 -2 RS Tx Rx G Extron HDMI Pro Cable 5 MI 6 3 A 4
PAGE 5
“Show Me” Cables The Extron “Show Me” cables are for use with Extron TeamWork systems. They feature a Share button for remote input source selection and a control pigtail, which may be wired directly into Extron switchers with contact closure and tally outputs.
PAGE 6
TeamWork • Installation Guide (Continued) System Controller The display and switcher in your system may be controlled by RS-232, Ethernet, or IR, depending on the models. The IPLink control processor must be configured to communicate correctly with the display and switcher. See the user guide for the controller for complete instructions about configuration. The guide is available at www.extron.com.
PAGE 7
Addendum This section provides additional information about the specific requirements of the IPL T PC1 and IPL T PC1i controllers. When using the IPL T PC1i system controller (International TeamWork kits) you must replace the power plug on the display with the provided IEC C14 male power cord plug (see page 8). Extron IPL T PC1 or IPL T PC1i TeamWork systems require a display that returns to the previous state when the power cord is disconnected and then plugged back in.
PAGE 8
TeamWork • Installation Guide (Continued) NOTES: • Always check and test compatibility before installation. Some systems may require advanced configuration of the system controller and require the display to be controlled by RS-232, Ethernet, or infrared. • Some displays support a lockout of local buttons. Extron recommends that, after setup, user accessible controls are locked whenever possible. This ensures the display remains optimized for the TeamWork system.