Operating Manual iTAG X30
Document Number X124749(1) (See DDM for the latest Version) For warranty information, refer to Terms and Conditions at http://www.extronics.com ©2020 Extronics Limited. This document is Copyright Extronics limited. Extronics reserve the right to change this manual and its contents without notice, the latest version applies.
Contents 1 2 3 4 5 Introduction.......................................................................................................... 5 1.1 What is inside the box? ................................................................................. 5 1.2 Pre-requisites ................................................................................................ 5 1.3 Reference documentation ............................................................................. 5 Safety Information ..........
6 7 5.1 EU Declaration of Conformity ...................................................................... 21 Manufacturer ..................................................................................................... 24 Radio Equipment – FCC Warning Statement ....................................................
1 Introduction The iTAG X30 worker location tag with hybrid technology, allows for accurately locating workers in Hazardous and Non-Hazardous areas, anytime anywhere. The iTAG X30 tag provides, audible, visual and tactile alerts and works with Stanley healthcare MobileView software to provide real-time alerting and reporting, for worker location solutions. 1.1 What is inside the box? • • • iTAG X30 iTAG X30 charging cable Quick start guide 1.
2 Safety Information 2.1 Storage of this Manual Keep this user manual safe and in the vicinity of the product. All persons required work on or with the product should be advised on where the manual is stored. 2.
2.3 Marking Information Where: • YYYY is the Notified Body for production • XXXXXX: is the serial number • ZZZZ is a code to identify model variants Exact layout of markings may differ from that shown.
3 Tag Features Emergency Call Button The iTAG X30 features a call button which can be activated in the case of an emergency, which triggers an event in MobileView to show the location of the worker in need of assistance. Visual, Audible and tactile indication The iTAG X30 features multiple LED's to indicate to the worker the tag is running, the call button has been activated and when the tag has a low battery.
Mounting The iTAG X30 comes complete with a stainless-steel clip which can be used to clip to PPE or used with a lanyard. Simple configuration The iTAG X30 Firmware contains 7 pre-defined configurations, which can be activated quickly and easily using the TED and Tag Manager BD. Motion sensor The iTAG X30 contains on-board motion sensors.
Click detect: 10
4.2.2 Activating the iTAG X30 On delivery from the factory, tags must be activated before configuring and use. A single tag or multiple tags can be activated simultaneously. To Activate a tag: Confirm the tag is detected.
• From the Detected Tags list, right click on the tag and select Activate. The tag colour indicator changes to green (Activated Tag). The tag LED will flash to indicate communication. • To activate multiple tags: Confirm the tags are detected. See Detected Tags 1. From the Detected Tags list, select the tags by checking their selection boxes (or check the box in the column header to select them all) 2. Under the selection Tag Configuration, select Activate and check the Tag state box. 3. Click Apply.
The tag colour indicator changes to green (Activated Tag) 4. Click Finish. 4.2.3 How to Configure The iTAG X30 must be initially configured using the TMBD application (Tag manager BD application, which is part of the Hardware manager application) The TMBD application allows you to activate and configure the following tag parameters according to sites infrastructure and use case. More information can be found in the Tag manager BD Guide.
WPA-PSK: 14
4.2.4 Available configurations The tag firmware contains 7 pre-defined configurations. These configurations define the tag type and beacon rate behaviour. Each configuration has a unique ID number called a “Static Configuration” which cannot be edited. Only 1 configuration can be selected and used per tag.
The following table shows the available configurations.
Battery Status Low battery - Red flashing Critical low battery – Red Static Battery Charging – Red Static Battery Charged – Green Static 4.4 Mounting the tag Ensure the tag is worn in an upright position. For best results wear the tag as high up your body as possible. • Tag clipped to pocket • Tag clipped to epilate • Tag clipped to chest pocket 4.5 Battery The iTAG X30 has a non-replaceable rechargeable Lithium Ion Battery and is charged using the Charging cable included.
• • • • • 4.5.3 Changes in transmission interval Temperature Motion Indoor/Outdoor applications Time to receive firm GPS co-ordinates Battery Capacity The tag’s battery capacity degrades over a period, depending on the number of charge cycles. 4.5.4 Charging the Battery The iTAG X30 is charged using the USB Charging Cable provided. It its attached and detached from the rear of the tag as shown: The charger input conditions listed in the Special Conditions of Safe Use must be observed.
4.7 Authorized Persons Only persons trained for the purpose are authorized to handle the iTAG X30; they must be familiar with the unit and must be aware of the regulation and provisions required for explosion protection as well as the relevant accident prevention regulations. 4.8 Cleaning and Maintenance The iTAG X30 and all its components require no maintenance and are self-monitoring. All work on the iTAG X30 must be carried be performed by Extronics approved personnel. 4.8.
5 Variants Tag Variants iTAGX30AI iTAGX30AI-HID iTAGX30USC iTAGX30USC-HID iTAGX30AI-PK50 iTAGX30AI-HID-PK50 iTAGX30USC-PK50 iTAGX30USC-HID-PK50 iTAG X30 Hazardous Area Hybrid technology tag with Wi-Fi and GPS, accommodates photo ID/access control. Certified to ATEX, IECEx Complete with USB charging cable iTAG X30 Hazardous Area Hybrid technology tag with Wi-Fi and GPS, accommodates HID iClass tag and photo ID.
5.
6 Manufacturer The iTAG X30 is manufactured by: Extronics Ltd, 1 Dalton Way, Midpoint 18, Middlewich Cheshire CW10 0HU UK Tel. +44(0)845 2775000 Fax. +44(0)845 2774000 E-mail: info@extronics.com Web: www.extronics.com OR Under licence by: Omni-ID Inc. 333 West Commercial Street Suite 333 – 1500 East Rochester N.Y. 14445 U.S.A Tel. +1-585-299-5990 Fax. +1-585-672-4152 E-mail: sales@omni-id.com Web: www.omni-id.com/ Or one of its affiliates.
7 Radio Equipment – FCC and ISED Warning Statement FCC & ISED Warning statement: This device complies with Industry Canada’s licence-exempt RSSs and Part 15 of the FCC Rules. • Operation is subject to the following two conditions: o This device may not cause interference; and o This device must accept any interference, including interference that may cause undesired operation of the device. Please see Section 8.4 of RSS-Gen Issue 4 for further information.