Installation Guide

10258 REV 05-09-16
Patented
LIFETIME WARRANTY. Please register at www.ezaccess.com/warranty-satisfaction.
CE Technical Files kept at: Enable Access, Marshmoor Works Great North Road, North Horth Mymms Hatfield, AL9 5SD, UK
© EZ-ACCESS
®
, a division of Homecare Products, Inc. All rights reserved.
All text and images contained in this document are proprietary and may not be shared, modified,
distributed, reproduced, or reused without the express written permission of EZ-ACCESS.
Patent No. 8,191,193
CE Technical Files kept at: Enable Access, Marshmoor Works Great North Road, North Horth Mymms Hatfield, AL9 5SD, UK
© EZ-ACCESS
®
, a division of Homecare Products, Inc. All rights reserved.
All text and images contained in this document are proprietary and may not be shared, modified,
distributed, reproduced, or reused without the express written permission of EZ-ACCESS
Instructions
SUITCASE
®
TRIFOLD
®
AS Ramp
Optional Top Lip Extension is available. Contact your local EZ-ACCESS retailer for details.
RATED LOAD
Maximum weight limit is 800 pounds.
INSTALLATION
1. Read and follow all instructions before use.
2. Do not use if ramp is damaged or unstable.
3. For wheelchairs and scooters only (not intended for
commercial use).
4. Ramp is shipped fully assembled. To separate ramp into two
halves for easy stowage and transportation, remove bolts and
install hinge pins as follows:
a. Position as shown in (FIGURE 1). Align hinges, then insert
hinge pin into each hinge assembly and connect ramp
sections together before use. Spring section of pin should
be on the underside (non-treaded side) of ramp.
Ramp may be separated for use when loading or
unloading unoccupied mobility equipment only.
When used with occupied mobility equipment, use
ramp as one unit (ensure both halves are joined with
hinge pins or bolts firmly installed before use).
5. Place ramp on landing in the folded position, making sure that
the top lip transition plate (labeled TOP) is resting securely on
the landing, see FIGURE 2.
6. Position ramp approximately its full length out from vehicle or
step. Facing vehicle or step, begin working from the left side.
Stand ramp upright on end with the hinged edge facing to the
right. Lift up first top half of ramp toward step or vehicle and
place ramp so that the top lip transition plate is securely
supporting the ramp as shown in FIGURE 2.
7. Unfold second top half of ramp so that both halves are fully
extended lengthwise with one half lying face down on top of
the other. NOTE: Applied slip-resistant tread should NOT be
exposed at this time. Open complete ramp, exposing entire
applied slip-resistant tread surface, then center on landing as
shown in FIGURE 3.
8. For ease in carrying and stowage, ramp can be disconnected
and carried in two sections. (When hinge pins are not in use,
store in one side of hinge or on the underside of ramp by
inserting into the gap behind the top I-beam.)
9. To prevent ramp halves from swinging open, ensure that the
Dual Lock™ tab (interlocking fastener) is pressed together and
firmly locked in place. Prior to use, locate both of the 1” x ¾”
Dual Lock tabs (found opposite the applied slip-resistant tread
side of the ramp, near the top and bottom edges), and then
remove the top piece (it’s used only as a protective covering).
WARNING!
Ensure top lip transition plate is secure before using ramp.
We recommend attaching ramp temporarily to the landing
using provided clevis pins (drill ¼” hole in landing) or semi-
permanently using screws through pre-drilled holes at the top
of each section. To prevent ramp from becoming dislodged
during use, make sure that the top lip transition plate overlaps
the resting surface as far as possible.
The surface holding the top lip transition plate needs to be
substantial and of sound construction.
Ramp may be slippery when wet or icy.
Use ramp only with a qualified helper and always use lap belt.
An incline chart is provided on the reverse side of this
document. However, it is intended only as a guideline. It is
important that you refer to your equipment's (wheelchair or
scooter) Owner Guide for the proper degree of incline/decline
and chair direction before using ramp. Never exceed its
recommendations.
SAFETY & MAINTENANCE
Regularly check ramp for damage, and check and tighten any loose
fasteners. Keep ramp surface clear of ice, snow, dirt, leaves, and
other debris. For snow/ice, remove accumulation and sweep the
surface clean. To remove dirt, leaves, and other debris, sweeping
the surface or using a garden hose will usually suffice, but, if
needed, use a damp cloth or soft brush with non-alkaloid detergent
and water. Rinse well and use extra caution if ramp surface is wet.
OPTIONAL ACCESSORY
Increase the usefulness of the SUITCASE
®
Trifold AS ramp with the
Top Lip Extension (TLE). This optional extension increases the
standard 3” top lip
transition plate to
become 9”,
allowing the ramp
to clear the rear
bumper of SUVs
and vans by
simply attaching to
the top lip of the
ramp. TLE is for
use with
unoccupied
mobility
equipment only and, when used, reduces the overall ramp weight
capacity to 500 pounds. Contact your local retailer or visit
www.ezaccess.com.
FIGURE 1
FIGURE 2
FIGURE 3