Instructions / Assembly

ManualsBrandsEZ Screen Room ManualsKitchenScreen Roller Tool

WORKINGWITHSCREENANDSPLINE:



FIRSTPRACTICEHOWTHEFLATSPLINEFITS



INTOTHESCREEN

CHANNEL.CUTA6”PIECEOFSPLINE. USINGYOURFINGERS,

PUSHTHEFLATSIDEOFTHESPLINEINTOTHE



DEEPEREDGEOF

SPLINECHANNEL(WITHOUTANYSCREEN).NOWPRACTICE

ROLLINGTHESPLINEROLLERTOOLTO“LOCK”

THESPLINEINTOTHE SPLINECHANNEL. (Seeillustrations).



NOTE:“Flatedge”ofsplineseatsinflatedgeofchannel.



PROPERWHEELSELECTIONFORSPLINEROLLINGTOOL

U‐shapedwheelRoundwheel



Eitherwheelisacceptable

Summary of content (6 pages)

PAGE 1
WORKING WITH SCREEN AND SPLINE: 1. FIRST PRACTICE HOW THE FLAT SPLINE FITS INTO THE SCREEN CHANNEL. CUT A 6” PIECE OF SPLINE. USING YOUR FINGERS, PUSH THE FLAT SIDE OF THE SPLINE INTO THE DEEPER EDGE OF SPLINE CHANNEL (WITHOUT ANY SCREEN). NOW PRACTICE ROLLING THE SPLINE ROLLER TOOL TO “LOCK” THE SPLINE INTO THE SPLINE CHANNEL. (See illustrations). NOTE: “Flat edge” of spline seats in flat edge of channel.
PAGE 2
WORKING WITH SCREEN AND SPLINE: WHEN SCREENING YOUR OPENING, FOLLOW THE DIAGRAM BELOW AS TO THE ORDER IN WHICH TO SCREEN THE CHANNELS, START AT BOTTOM PANEL #1 AND FINISH AT #4. THEN MOVE TO 1‐4 OF THE LARGER TOP PANEL. BE SURE TO READ AND UNDERSTAND THIS ENTIRE SECTION BEFORE YOU BEGIN THE SCREENING PROCESS. 1 Top Panel 1. Screen channel (F) Top Panel 2. Screen channel (E) 3 2 3. Screen channel (D) 4. Screen top channel (C) 4 Bottom Panel 1. Screen bottom channel (C) 1 3 2 Bottom Panel 2.
PAGE 3
INSTALLING SCREEN‐ LOWER PANEL: 12. TAPE OR TACK THE SMALLER BOTTOM PANEL SCREEN (S1) LOOSELY OVER LOWER OPENING (BELOW MIDRAIL). OVERLAP ALL EDGES AT LEAST 3”. Note: Extra screen is supplied. Masking tape (not included) Masking tape (not included) 13. USE A PIECE OF 10’ SPLINE (S3) TO BEGIN INSTALLING THE LOWER SCREEN PANEL. REFER TO PAGE 12.
PAGE 4
INSTALLING SCREEN continued‐ LOWER PANEL: 14. ALIGN MIDDLE OF SPLINE WITH THE MIDDLE OF THE MIDRAIL (C). ROLL THE SPLINE AND SCREEN INTO THE CHANNEL TOWARDS EITHER CORNER. Allow extra screen 15. MEASURE SIDE (A) AND CUT OFF PIECE OF SPLINE 6” LONGER. 16. STARTING ABOUT 1” BELOW THE UPPER RIGHT CORNER, ROLL THE SPLINE AND SCREEN INTO THE CHANNEL. ENSURE SPLINE COVERS ENTIRE SCREEN CHANNEL. 17.REPEAT STEP 15 FOR SIDE B. APPLY A SLIGHT SIDEWAYS PRESSURE WITH YOUR FINGERS AS YOU ROLL SIDE B.
PAGE 5
INSTALLING SCREEN continued ‐ LOWER AND UPPER PANELS 18. STARTING IN THE MIDDLE OF (F), ROLL THE SPLINE AND SCREEN INTO THE CHANNEL TO‐ WARDS EITHER CORNER. NOW THAT THE TOP (F) IS DONE, COMPLETE BOTH SIDES AS YOU DID WITH THE LOWER PANEL. NOTE: AS THE SPLINE LOCKS INTO PLACE YOUR SCREEN SHOULD BECOME TIGHT. IF NECESSARY REMOVE SPLINE AND RESTART PROCESS UNTIL YOU ACHIEVE DESIRED LOOK AND SCREEN TAUTNESS. 19. REPEAT STEPS 12‐18 FOR UPPER PANEL (ABOVE MIDRAIL).
PAGE 6
TRIMMING THE SCREEN: 20. CAREFULLY TRIM OFF EXCESS SCREEN THAT IS OUT‐ SIDE THE SPLINE USING A SHARP UTILITY KNIFE. 21. TUCK SPLINE INTO CORNERS USING THE TIP OF A SCREWDRIVER.