User's Manual
Table Of Contents
- Part # BL600-SA, BL600-SC, BL600-ST
- 3.1 SW Block diagram
- 3.3 Electrical Specifications
- 4.2 Measured waveforms
- 4.3 Peripheral block current consumption
- 5.1 Power management (includes brown-out and power on reset)
- 5.2 Clocks
- 5.3 Memory for smartBASIC application code
- 5.4 RF
- 5.5 UART Interface
- 5.6 SPI Bus
- 5.7 I2C Interface
- 5.8 General Purpose I/O and ADC
- 6.1 Circuit Components Required on Host PCB
- 6.2 BL600-Sx General PCB Layout on Host PCB
- 6.3 BL600-SA Layout on Host PCB
- 6.4 BL600-ST Layout on Host PCB
- 8.1 Introduction
- 8.2 Shipping
- 8.3 Reflow Parameters
- 9.2 OEM Responsibilities
- 10 Japan (MIC) Regulatory
- 11 CE Regulatory
- 12 EU DECLARATIONS OF CONFORMITY
- 14 ORDERING INFORMATION
BL600-Sx
Single Mode BLE Module
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
For BL600-ST:
FCC Radiation Exposure Statement:
This equipment complies with FCC /IC radiation exposure limits set forth for an uncontrolled
environment and is safe for intended operation as described in this manual.
LMA approval for BL600-ST:
This device (BL-600ST) meets the requirement of a limited module approval. It must attached to
below host and antenna.
Host information
Brand name : Laird , Model name :
DVK-BL600-ST, with a RSMA
Antenna information
Brand name: MAG. LAYERS, Model name: EDA-8709-2G4R2-A40-CY
Antenna connector
RSMA
Integration is typically strictly restricted to Grantee himself or dedicated OEM integrators under
control of the Grantee.
IMPORTANT NOTE:
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module.
Under such configuration, the FCC radiation exposure limits set forth for an
population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that the FCC radio-frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then
additional FCC part 15.19 statement is required to be available in the users’ manual: This device
complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " BL600-SA & BL600-SC
Contains FCC ID: PI4BL600; BL600-ST Contains TX FCC ID: PI4BL600T ". If the size of the end product
is
larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on
the
label: This device complies with Part 15 of FCC rules. Operation is subject to the following
two
conditions: (1) this device may not cause harmful interference and (2) this device must
27
www.lairdtech.com/wireless Laird