User's Manual
Table Of Contents
- Part # BL600-SA, BL600-SC, BL600-ST
- 3.1 SW Block diagram
- 3.3 Electrical Specifications
- 4.2 Measured waveforms
- 4.3 Peripheral block current consumption
- 5.1 Power management (includes brown-out and power on reset)
- 5.2 Clocks
- 5.3 Memory for smartBASIC application code
- 5.4 RF
- 5.5 UART Interface
- 5.6 SPI Bus
- 5.7 I2C Interface
- 5.8 General Purpose I/O and ADC
- 6.1 Circuit Components Required on Host PCB
- 6.2 BL600-Sx General PCB Layout on Host PCB
- 6.3 BL600-SA Layout on Host PCB
- 6.4 BL600-ST Layout on Host PCB
- 8.1 Introduction
- 8.2 Shipping
- 8.3 Reflow Parameters
- 9.2 OEM Responsibilities
- 10 Japan (MIC) Regulatory
- 11 CE Regulatory
- 12 EU DECLARATIONS OF CONFORMITY
- 14 ORDERING INFORMATION
BL600-Sx
Single Mode BLE Module
Pin No
Pin
Designation
Default
Function
Alternate
Function
Default
Direction
Notes
Comment
scaling
7
SIO_5
DIO
AIN
IN
1,2,3,4,5
8,9,10 bit resolution, Voltage
scaling
8 SIO_6
DIO
AIN IN 1,2,3,4,5
8,9,10 bit resolution, Voltage
scaling
9
SIO_7
DIO
IN
1,2
10
VCC
11
GND
12
SIO_8
DIO
I2C SDA
IN
1,2,4,5,6
I2COPEN() in smartBASIC
selects I2C function
13
SIO_9
DIO
I2C SCL
IN
1,2,4,5,6
14
15
SIO_10
SIO_11
DIO
DIO
SPI MOSI
SPI MISO
IN
IN
1,2,4,5,6
1,2,4,5,6
SPIOPEN() in smartBASIC
selects SPI function, MOSI
and CLK will be outputs
16 SIO_12
DIO
SPI CLK
IN 1,2,4,5,6
when in SPI master mode
17
GND
18 SIO_13
DIO
IN 1,2
19
SIO_14
DIO
IN
1,2
20 SIO_15
DIO
IN 1,2 Laird Devkit : Buzzer output
21
SIO_16
DIO
IN
1,2
Laird Devkit : Button 0 input
22 nRESET
IN
System Reset (Active low)
23
NC
DO NOT CONNECT
24 SIO_17
DIO
IN 1,2 Laird Devkit : Button 1 input
25
SIO_18
DIO
IN
1,2
Laird Devkit : LED 0
26 SIO_19
DIO
IN 1,2 Laird Devkit : LED 1
27
SIO_20
NC
Reserved for future use
28 GND
29
GND
30 RF_ANT
31
GND
32
33
SIO_21
SIO_22
UART TX
UART RX
DIO
DIO
OUT
IN
1,2,4,6,7
1,2,4,6,7
UARTCLOSE() selects DIO
functionality and
UARTOPEN() selects uart
34
SIO_23
UART RTS
DIO
OUT
1,2,4,6,7
comms behaviour
35
SIO_24
UART CTS
DIO
IN
1,2,4,6,7
36
SIO_25
DIO
IN
1,2
Laird Devkit : UART_DTR via
CON12
37 GND
38
SIO_26
NC
Reserved for future use. Do
NOT connect
39
SIO_27
NC
40
SIO_28
nAutoRUN
IN
In ONLY
Laird Devkit: UART_DSR via
CON12
8
www.lairdtech.com/wireless Laird