ezBattery Camera
About the Documents The documents include instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the documents is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the website (http://www.ezvizlife.com). Any and all information, including, among others, wordings, pictures, graphs are the properties of EZVIZ Inc.
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Camera SYNC Button Microphone Lens PIR Photoresistor LED Indicator Louderseaker Power Interface SD Card Slot Name Description SYNC Button Use to synchronize the base station. PIR With the PIR (Passive Infrared), the device can detect a human body to determine when there is a possible break in and begins to record footage. • Steady Red: The camera is starting. • Slow-Flashing Blue: The camera is starting to synchronize or the device is updating.
Base Station Power Button Main Button/LED indicator Reset Power Interface Network Interface/Network Indicator Name Description LED Indicator • Steady Green: The system works properly. • Steady Blue: Device is not connected to internet. • Flashing Blue: Memory card is formatting or device starting synchronization with the camera. Main Button Press to start synchronization with the camera (The synchronization lasts 2 mins). Press to connect or cut off power. (Opened by default.
Setup The camera should be used with the EZVIZ base station. Base station is sold separately (unless in bundle). Step 1 Insert Battery into Camera - Press the button as shown below to open battery cover. - Insert the battery. - Close the battery cover. Use the execlusive charger to charge the battery. Step 2 Power on the Base Station - Wait until the LED indicator turns to solid blue.
Make sure network indicator is on or flashing, Step 4 Synchronize Base Station with Camera(s) • Make sure the camera is within 2' to 3' (0.6 m to 1 m) of the base station. • The synchronization process takes about 2 minutes. 1. Press the Main Button on the Base Station. The circular LED indicator flashes Blue. 2. Press and hold the Sync button on the camera for 6 seconds. The LED indicator will slowly flash blue. When flashing blue becomes more rapid and then stops, sync is confirmed.
Step 5 Add the Base Station to Your EZVIZ Account 1. Create an user account. - Connect your mobile device to Wi-Fi. - Search “EZVIZ” in App Store or Google PlayTM to download. - Launch the App and register an EZVIZ user account. 2. Add Base Station to EZVIZ. - Log in the EZVIZ App. - At the Home screen, tap “+” on the upper-right corner to go to the scanning QR code interface. - Scan the QR Code on base station or manually enter the Serial Number to add base station.
Camera Installation Step 1 Pick a clean and flat surface, indoors or outdoors. • Camera and base station should be within the distance of up to 300 feet (100 m). Stay away from wireless device or barriers to aviod decreasing the communication distance. • Your camera provides a 111-degree viewing angel. Position your cameras to make sure the scene you want to video is in the cameras’ field of view. • Your camera motion sensor is far more sensitive to side-to-side movement across their field of view.
Charge the Battery The battery is fully charged when it leaves the factory. 1. Install the battery into the camera. 2. Connect the camera with power outlet via power adaptor (5V 1A).