Quick Start Guide www.ezvizlife.
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries. ALL RIGHTS RESERVED. About this Manual The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the ™ website (http://www.ezvizlife.com).
correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
Quick Setup Power Kit Installation Doorbell Installation Doorbell Setup
What's in the Box Mounting Plate (x3) Pick the one for best surveillance angle. Doorbell (x1) Faceplate (x3) Pick the one that best matched your home from three faceplates. Screwdriver (x1) Plate Foam (x1) Stabilize the mounting plate when installing it in the rough surface.
• If you have mechanical chime installed in your home, install the power kit and doorbell. • If you have electronic chime installed in your home, refer to its own manual to install the power kit, and install the doorbell. • If no chime is installed, skip power kit installation, install the doorbell and follow the Option B in page 5. Power Kit Installation 1 Shut off the electricity at the breaker that controls doorbell's circuit. 3 Remove the cover from your mechanical chime.
5 Connect the wire harness to the chime's terminals named TRANS and FRONT. 6 Insert the existing chime wire and the other end of the wire harness into the wire connector and twist it tightly. Repeat this step with the other chime wire. Wire Connector Chime Wire Wiring Overview REAR TRANS FRONT REAR TRANS FRONT DO NOT OIL Chime Wire Chime Wire 7 8 Mount the power kit to the side of the chime. 3 Put back the chime cover.
Doorbell Installation 1 Shut off the electricity at the breaker that controls 2 Optional) When the wall is uneven, paste the plate foam to the mounting plate. doorbell's circuit. 3 Insert the mini-level into the mounting plate and mark 4 the drill points when its bubble stays in the middle. Drill holes according to drill points and insert anchors. Anchor Mini-Level Remove the mini-level when drill points are marked.
5 6 Fix the mounting plate to the wall. Remove faceplate on your doorbell from buttom to top. Mounting Screw 7 If you have a chime installed, follow Option A; If not, follow Option B. Option A Connect doorbell with your existing doorbell wires. Fixing Screw U-Shaped Wire Option B Connect the fuse wire with your existing doorbell wire.
8 Fix the doorbell to the mounting plate by inserting the 9 doorbell screws. Restore the electricity at the breaker. Doorbell Screw Doorbell is powered on when its indicator flashes blue quickly. If not, make sure your electricity is off and check the wiring. If yes, proceed to doorbell setup. Doorbell Setup 10 Add to EZVIZ app. - Connect your mobile phone to Wi-Fi. - Download and install the EZVIZ app by searching “EZVIZ” in App Store or Google PlayTM.
Put the faceplate back and insert two security screws into the bottom of the doorbell to secure the faceplate. Security Screw Appendix Basics micro SD Card Slot Mounting Holes Terminals Reset Button Hold for 5s to reset and enter to AP mode. LED Indicator Blue Light Red Light Flashing Steady on Flashing Fast Steady on Doorbell is ready for Wi-Fi configuration. Doorbell is working. Device Exception Doorbell is powering on.
Use AP Mode for Wi-Fi Configuration -For - AP hotspot configuration, press the Reset button for 5 seconds and then you will hear voice prompt. -Wait - for a few seconds until you see the LED indicator flashes blue. -Follow the voice prompt to connect Wi-Fi. Wi-Fi Name: EZVIZ_XXXXX (9-digit Serial No.) Default Password: EZVIZ_XXXXXX (Verification Code) eg. Default Password: EZVIZ_ABCDEF Serial No. and verification code are listed on the cover of this manual. -Go back to EZVIZ app after successful connection.